Mini Wireless Optical Mouse with Color-Choice www.jascoproducts.
Package Contents • Mini Wireless Optical Mouse with Color-Choice • 2 AA batteries • Instruction Manual • Nano Receiver System Requirements • Windows® XP, Vista, Windows 7 • Mac 10.1 or higher • Available USB Port Left button Right button Optical sensor Scroll wheel On/Off switch Functional Introduction Installing the batteries 1. Turn off the power switch 2. Press the tab (as shown) to remove the top of the mouse. 3.
Press to remove top of mouse – + + – Press to remove battery restraint How to Remove the Nano Receiver 1. Press the tab (as shown) to remove the top of the mouse. 2. Remove the Nano Receiver from its location in the center of the mouse. Press to remove top of mouse Remove the Nano receiver stored in the Center between the batteries.
Setup the Connection between the Receiver and the Mouse 1. Plug the Nano receiver into the USB port of your computer. 2. Insert the batteries into the mouse. 3. Turn the On/Off Switch to On.
Changing the color clips 1. Locate the button at the rear of the mouse where the color clip meets the base. 2. Take the new color clip of your choice and position the front of it over the mouse, matching the plastic posts on the underside of the clip to the holes on either side of the scroll wheel. 3. Press the color clip down gently until you hear click into place. It is securely on the mouse now. Enjoy your new mouse color! Press your finger tip into the button to release the clip.
Trouble Shooting *Note: After periods of inactivity, the mouse goes into sleep mode to conserve battery life. To wake the mouse simply move it in any direction and it should respond on the screen If the mouse is not working, please follow the next steps: 1. Unplug the Nano from the USB Port wait 30 seconds and plug the Nano back in. 2. Check the batteries, they may need to be replaced. You will need 2 AA batteries. 3.
FCC Statement Notice: Federal Communications Commission (FCC) requirements, Part 15. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Mini ratón óptico inalámbrico con opción de color www.jascoproducts.
Contenido del paquete • Minimouse óptico inalámbrico de 2.4 GHz con nanorreceptor • 2 pilas AA (se incluyen) • Manual de instrucciones • Receptor de Nano Requisitos del sistema • Windows® XP, Vista, Windows 7 • Mac 10.1 o superior • Puerto USB disponible Botón izquierdo Botón derecho Sensor óptico Rueda de desplazamiento Interruptor de encendido y apagado Introducción a las funciones Instalación de las pilas 1. Apague el interruptor de encendido. 2.
Presione para retirar la tapa del mouse – + + – Presione para retirar el seguro de las pilas Cómo retirar el nanorreceptor 1. Para retirar la tapa del mouse, presione la lengüeta (como se muestra). 2. Retire el nanorreceptor de su alojamiento en el centro del mouse. Presione para retirar la tapa del mouse Retire el nanorreceptor que se aloja en el centro entre las pilas.
Establezca la conexión entre el receptor y el mouse 1. Conecte el nanorreceptor en el puerto USB de su computador. 2. Inserte las pilas en el mouse. 3. Encienda en interruptor de encendido y apagado. ! PRECAUCIÓN ! ADVERTENCIA Las pilas pueden soltar líquidos perjudiciales o sustancias inflamables o pueden explotar y causar lesiones y daños a los productos. Las pilas pueden soltar líquidos perjudiciales o sustancias inflamables o puedeexplotar y causar lesiones y daños a los productos.
Cambio de los clips de colores 1. Localice la ranura en la parte posterior del mouse donde el clip de color se une con la base. 2. Escoja un clip de otro color y coloque la parte frontal de éste sobre el mouse, de manera que las puntas de plástico en la parte inferior del clip encajen en los agujeros a cada lado de la rueda de desplazamiento. 3. Presione el clip de color hacia abajo suavemente hasta que oiga que los pasadores magnéticos encajan en su lugar. El clip ya está de forma segura en el mouse.
Solución de problemas *Nota: Tras periodos de inactividad, el mouse entra en modo sleep para preservar la vida de las pilas. Para activar el mouse, simplemente muévalo en cualquier dirección; éste debe responder en pantalla. Si el mouse no funciona, siga estos pasos: 1. Desconecte el nanorreceptor del puerto USB y espere 30 segundos. Conecte el nanorreceptor nuevamente. 2. Compruebe las pilas; puede que necesite remplazarlas. Necesitará 2 pilas tamaño AA. 3.
Declaración de FCC Aviso: Requisitos de FCC (Comisión Federal de Comunicaciones), sección 15. Este equipo ha sido probado y cumple con los límites para dispositivos digitales de clase B, de conformidad con la sección 15 de las normas de FCC. Dichos límites se diseñaron para ofrecer protección razonable contra interferencias perjudiciales en instalaciones residenciales.