Installation Guide

ManualsBrandsGE ManualsIndoor FixturesGE ABH2

Lighting

Installation Guide

imagination at work

Modular High & Low Bay Lighting

(ABH2-series)

Features

• 5 year warranty

• Damp location rated

Albeo

LED Luminaire

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING/AVERTISSEMENT

RISK OF ELECTRIC SHOCK

• Turn power off before inspection, installation or removal.

• Properly ground electrical enclosure.

RISK OF FIRE

• Follow all NEC and local codes.

• Use only UL or IEC approved wire for input/output connections.

Minimum size 18 AWG.

RISQUES DE DÉCHARGES ÉLECTRIQUES

• Coupez l’alimentation avant d’’inspecter, installer ou déplacer le luminaire.

• Assurez-vous de correctement mettre à la terre le boîtier d’alimentation électrique.

RISQUES D’INCENDIE

• Respectez tous les codes NEC et codes locaux.

• N’utilisez que des ls approuvés par UL ou IEC pour les entrées/sorties de

connexion. Taille minimum 18 AWG.

Save These Instructions

Use only in the manner intended by the manufacturer. If you have any questions, contact the manufacturer.

Prepare Electrical Wiring

Electrical Requirements

• The LED driver must be supplied with 120-480 VAC, 50/60 Hz per product label and connected to an individual

properly grounded branch circuit, protected by a 15 or 20 ampere circuit breaker.

Grounding Instructions

• The grounding and bonding of the overall system shall be done in accordance with National Electric Code

(NEC) Article 600 and local codes.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-3 (A)/NMB-3(A)

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

Summary of content (4 pages)

PAGE 1
GE Lighting Installation Guide Albeo LED Luminaire TM Modular High & Low Bay Lighting (ABH2-series) Features • 5 year warranty • Damp location rated BEFORE YOU BEGIN Read these instructions completely and carefully. WARNING/AVERTISSEMENT RISK OF ELECTRIC SHOCK • Turn power off before inspection, installation or removal. • Properly ground electrical enclosure. RISK OF FIRE • Follow all NEC and local codes. • Use only UL or IEC approved wire for input/output connections. Minimum size 18 AWG.
PAGE 2
Unit Installation 1 Carefully unpack unit and properly inspect for defects before installing. Wear work gloves to prevent dirt and oil from being transferred to the luminaire. 2 Choose a mounting method: chain or cable, rod mount, or pendant mount. (Chain or cable is covered here. Other options are covered in the section Optional Mounting Methods). Fixture Weight ABH2-series LED Modules 1 2 3 4 6 3 Attach to structural member Max. Weight (lbs.
PAGE 3
Electrical Connections (347/480V) A) Conduit B) Power cord 1 Loosen screws to remove endcap. 2 A) Install 1/2” conduit, or B) install AC power cord with strain relief. 3 Connect AC line to fixture’s power supply using UL listed wire connectors. Green to green (ground), red to black (line) and black to white (neutral). 4 Re-attach endcap.
PAGE 4
OPTION B Pendant Mount Kit NOTE: Pendant Mount Kit cannot be used with the 6-module fixture. AC line 1 Attach pendant mount bracket assembly to four mounting inserts on the fixture with (8) 10‐32 x 3/8” Philips pan head screws. 2 Attach top plate to 3/4” conduit and pass AC input wires through conduit, top plate, and locking nut (if used). Connect the AC input wires to the fixture wires coming from the strain relief in the main bracket assembly bottom plate.