Installation guide

ManualsBrandsGE ManualsDishwasherOfficial GE cafe dishwasher

Appliances

Installation Instructions

Built-In Dishwasher

If you have questions, call 800.GE.CARES{800.432.2737} or visit our website at: www.ge.com

In Canada call 1-800-561-3344 or www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

IM PO RTANT-The dishwasherMUST

beinstalledtoallowforfutureremovalfromtheenclosure

if service is required.

IM PORTANT-Observe allgoverningcodes and

ordinances.

• Note to Installer- Be sure to leavethese instructionsforthe

consumer's and localinspector'suse.

• Note to Consumer - Keep these instructionswith your

Owner's Manual for future reference.

• Skill Level - Installation of this dishwasher requires

basic mechanical, electrical and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the GE Appliance Warranty. See warranty information.

• Completion Time - 1 to 3 Hours. New installations require

more time than replacement installations.

If you received a damaged dishwasher, you should

immediately contact your dealer or builder.

Optional Accessories - See the Owner's Manual for available

custom panel kits.

FOR YOUR SAFETY

Read and observe all CAUTIONS and WARNINGS

shown throughout these instructions. While performing

installations described in this booklet, gloves and either

safety glasses or goggles should be worn.

READ CAREFULLY.

KEEP THESE INSTRUCTIONS.

PDW8200 Series

PDW8400 Series

PDW8700 Series

PDW8800 Series

PDW8900 Series

PDW9200 Series

PDW9700 Series*

PDW9800 Series

PDW9900 Series

CDW9000 Series

*For PDW9700 Series also refer to the Instructions

provided on the template packed with that model.

(WD35XlOO5)

(__) imag

ination at work

Summary of content (13 pages)

PAGE 1
Appliances Installation Instructions Built-In Dishwasher If you have questions, call 800.GE.CARES{800.432.2737} or visit our website at: www.ge.com In Canada call 1-800-561-3344 or www.geappliances.ca BEFORE YOU BEGIN Read these instructions completely IM PO RTANT- The dishwasherMUST be installed toallowforfutureremovalfromtheenclosure and if service is required. carefully.
PAGE 2
Installation Preparation PARTS SUPPLIED: [] Two #8-18 x 5/8" Phillips special head screws, to secure dishwasher to underside of countertop or sides of cabinets. (Screws located in user bag.) #8 Phillips Hex-Head SpecialHeadScrews Screw [] Side and top trim pieces 5/8" long 1/2" long [] Trim Panel Accessory Kit (not shown).
PAGE 3
Installation Preparation PREPARE DISHWASHER • The dishwasher must be installed so that drain hose is no ENCLOSURE more than 10' in length for proper drainage. WARNING )es or wires To reduce the risk of electric shock, fire, or injurg to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation.
PAGE 4
Installation Preparation PREPARE ELECTRICAL WIRING FOR PERSONALSAFETY: Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter plug with this appliance. Electrical Requirements • This appliance must be supplied with 120V, 60Hz., and connected to an individual properl9 grounded branch circuit protected by a 15 or 20 ampere circuit breaker or time delag fuse. • Wiring must be 2 wire with ground and rated for 75°C(176°F).
PAGE 5
Installation Instructions PREPARE HOT WATER LINE STEP i INSTALL TRIM PIECES • The line may enter from either side, rear or floor within the shaded area shown in Figure F. • The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" diameter hole to accommodate the water line. If power cord with plug is used, water line must not pass through power cord hole. • Locate trim strips inside dishwasher. • Press trim onto the tub flange on each side.
PAGE 6
Installation Instructions PDW9200-PDW9900, CDW9000 Series STEP 4 REMOVE TOEKICK • Remove the 2 toekick screws and toekick. Set aside for use in Step 19. Remove 2 Toekick Screws Figure K STEP 5 REMOVE TOEKICK BRACE PulleL Decrease Tension Shouldel Correct Spring Cable Routing Increase Tension Figure I Tip: If door does not open easily or falls too quickly, check the spring cable routing. Check that the cable is properly aligned on the pulley.
PAGE 7
Installation Instructions STEP 7 INSTALL 90 ° ELBOW • Push hose over the drain outlet on the back side of the • Wrap 90° elbow with thread seal tape. • Install a 90° elbow onto the water valve. dishwasher. See Figure R Push the hose over the outlet and against the shoulder stop.
PAGE 8
Installation Instructions STEP 21 POSITION DISHWASHER UNDER CO UNTE RTO P • Push the dishwasher into the cabinet. • Push the sides with gour hands. Do not use gour knee against the door since door damage will occur. • Check that the tub insulation blanket does not get "bunched-up" or interfere with the springs as gou slide it into the cabinet. • Center the dishwasher in the opening. • Front of door panel should be flush with face of cabinet.
PAGE 9
Installation Instructions STEP 22 LEVEL DISHWASHER IM PORTANT- Dishwasher must be levelforproper dishrack operationand wash performance. • For PDW9200-PDW9900, CDW9000 Series:Make sure 1/2"minimum gap ismaintained (seeFigureX). • Place levelon door to check thatthe dishwasher islevelsideto-side. Place levelon racktrackinsidetub to check thatthe dishwasher islevelfront-to-back. / \, STEP 13 SECURE DISHWASHER TO COUNTERTOP OR CABINET In this step you will need the 2 Phillips special head Side-Mountin_ -
PAGE 10
Installation Instructions Compression Nut STEP 14 CONNECT WATER SUPPLY Ferrule Connect water supply line to the 90 ° elbow. • Slide compression nut, then ferrule over end of water line. • Insert water line into 90° elbow. • Slide ferrule against elbow and secure with compression nut. Hot Water _0 ° Elbow Supply Line IN PO RTANT- Check to be sure that door spring does not rub or contact the fill hose or water supply line. Test by opening and closing the door.
PAGE 11
Installation Instructions STEP 16 CONNECT POWER SUPPLY STEP 17 PRETEST CHECK LIST Skip this step if dishwasher is equipped with power cord. Verifg that power is turned off at the source. If a power cord with plug is used, proceed to Step 16. • Locate the junction box cover within the user bog. • Secure house wiring to the back of the junction box with a strain relief. Review this list after installing gour dishwasher to avoid charges for a service call that is not covered bg gour warrantg.
PAGE 12
Installation Instructions STEP 18 DISHWASHER WET TEST [] Turn on power supply (or plug power cord into outlet, if equipped). [] Start the unit to check for leaks.
PAGE 13
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE GE Consumer General Louisville, ge.com & Industrial Electric Company Kentucky 40225 © 2007 General Electric Company Pub. No. 31-30233 Dwg. No.