Specification Sheet

ManualsBrandsGE ManualsOutdoor FixturesGE Criterion

AREA LIGHTING

Guide Form Specifications – 2011

Lighting Solutions

GUIDE FORM SPECIFICATIONS

CRITERION ™ WALLPACK LUMINAIRE

The totally enclosed, weather-resistant luminaire desig-

nated___ (identify) shall be a GE CRITERION

_________(specify

Cuto or Forward Throw) WALLPACK luminaire, ordering num-

ber_______________ (specify CCDX, CCSX, CCMX, CTDX, CTSX, or

CTMX, plus ordering number logic from catalog) or approved equal,

to operate one ____(specify 250, 400) watt high pressure sodium

or ______ (specify 175, 250, 400) watt metal halide mogul base or

one ______ (specify 50, 70, 100, 150) watt high pressure sodium or

_______ (specify 50, 70, 100, 150, 175) watt metal halide medium

base lamp from a nominal _____(specify 120, 208,240, 277, or 480)

volt, 60 hertz power source. The luminaire shall include an integral

prewired SnapDrive

ballast assembly or prewired DirectMount

ballast assembly (for the smallest size wall pack) and optical

assembly that shall produce a ___________ (specify adjustable

forward throw or cut-o) distribution. The luminaire shall have UL/

cUL listing SUITABLE FOR WET LOCATIONS. The standard housing

construction shall be IP65. Ballast, housing, optical, and luminaire

assembly shall all be built to GE Lighting Systems specications.

The luminaire shall include a die-cast aluminum housing with a

polyester powder paint nish, glass lens, and continuous silicone

gasket with no gaps to insure sealing. The luminaire shall have

tool-less entry or optional tamper-resistant entry to prevent unau-

thorized entry. Tamper resistant entry is standard on the 70W Di-

rectMount luminaire (required because of its low mounting height).

The housing shall be equipped with standard pre-punched keyhole

slots for ease of mounting. Door removal shall be accomplished

by a sliding notch hinge for quick and simple removal except for

the 70 and lower wattage DirectMount luminaires. All hardware

shall be corrosion-resistant. ½” NPT plugged conduit entrances

for through feed shall be optional except for the 70 and lower

wattage DirectMount luminaire. The luminaire shall have provision

for optional factory installed photoelectric control. The luminaire

design shall be tested and certied to withstand 2 G 300,000 cycle

rst harmonic 3 axis (100K cycles in each major axis) shake test fol-

lowed by a 4G 10,000 cycle shake test without any major failures.

Ballast, ignitor, capacitor, and printed circuit board wiring shall

be installed onto a modular SnapDrive

Electrical System that

snaps in and out of the luminaire without tools except for the 70

and lower wattage DirectMount which has ballast components

mounted to the luminaire housing. Voltage changes, wattage

changes (250 and 400 watt only), and the addition of optional

EZAdd

quartz switching device (400 watt only) shall be ac-

complished with the use of quick-change jumpers that shall be

located on the ballast printed circuit board except for the 70W

Direct Mount luminaire. SnapDrive

Electrical Systems shall be

interchangeable into other luminaires in the Criterion

family of

the same wattage size. The luminaire shall contain a standard

Auto-regulator (CWA) or Lag ballast for use with metal halide, or

high-pressure sodium lamps. Optional factory installed fusing shall

be available for all discrete voltages and wattages. The ballast

shall be compliant with NEMA specications and lamp manufactur-

ers specications at the time of manufacture. The ballast shall reli-

ably start and operate the lamp in ambient temperatures down to

–20 degrees F for metal halide and –40 degrees F for high-pressure

sodium. Pulse start metal halide ballasts shall be available from

35-400-watts. Each SnapDrive

Electrical System shall have a

receptacle that is compatible with the GE Diagnostic Tester that will

enable electrical testing and trouble shooting.

The optical assembly shall have a precision hydroformed

aluminum reector that has a chemically bonded lightweight non-

breakable ALGLAS

nish on all surfaces for precise light control in

combination with heat and impact resistant tempered at lens.

The forward throw reector shall be adjustable for accurately

tune the light placement and the lamp will be shielded to minimize

glare. The cuto reector shall be designed and constructed to

conform to stringent dark-sky standards and to please the neigh-

bors. The luminaire shall be supported by a dedicated web site

that will contain down-loadable IES photometric les.

Forward

Throw

Cutoff

OPTICAL ASSEMBLY

MECHANICAL CONSTRUCTION

GENERAL DESCRIPTION

BALLAST OPERATION

Summary of content (2 pages)

PAGE 1
g AREA LIGHTING GE Lighting Solutions GUIDE FORM SPECIFICATIONS CRITERION ™ WALLPACK luminaire GENERAL DESCRIPTION The totally enclosed, weather-resistant luminaire designated___ (identify) shall be a GE CRITERION TM _________(specify Cutoff or Forward Throw) WALLPACK luminaire, ordering number_______________ (specify CCDX, CCSX, CCMX, CTDX, CTSX, or CTMX, plus ordering number logic from catalog) or approved equal, to operate one ____(specify 250, 400) watt high pressure sodium or ______ (specify 175, 2
PAGE 2
g GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com 1-88 8 - 6 9 - 4 3-5 3 3 GE Lighting Solutions is a subsidiary of the General Electric Company. Evolve and other trademarks belong to GE Lighting Solutions. The GE brand and logo are trademarks of the General Electric Company. © 2011 GE Lighting Solutions. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.