Simple DIY Setup [| Q myo! [Le] Ltt] Lil] your Smart JL CUTE RT your Smart Switch to Ei] the C by GE app
Compatibility Requirements Rating 120V AC 60Hz Works with halogen, incandescent and LED bulbs, Neutral wire is required including C by GE Smart {Wire Is usually white Bulbs. org LED up fo 1.25 amps Ground wire Is required {Wire is usually green, Incandescent/halogen green with a yellow stripe, up te 5 amps or caper) Gator up to 1/4HP WI-Fi 802.11 b/g/n @ 2.
MAGENTA | IMPORTANT NOTE ON 3-WAY WIRING: Some lights have one wall switch, while others are controlled by two or more wall switches (such as stair lights, which have a switch at both the top and bottom of the stairs). If your lights have more than one switch {called a 3-way), we've created instructions for how te install and enable the capability. Visit for 3-way Installation Instructions and how-to-videos.
You Got This! And we're here to help.
BEFORE YOU DO ANYTHING: Step 1 Turn Off The Power! Tum off the power for the switch location at the circuit breaker box. Test existing switch by li switch on/off, ensuring pti not tum on. Now, follow these setup steps for a single gang switch.
STEP 2 Remove Your Old Switch 1. Remove the existing wall plate and switch from the wall. 2. Use voltage tester on the black wires to confirm power to the switch is off (recommended). 3. Before disconnecting the wires from the wall, label each with the provided wire labels. A Ventral and ground wir ore required. If you don't have father wire, the C by GE fishwife is not compatible. 4. Disconnect wires and remove existing switch.
= Line Load Ground® Neutral Wire Labels Far Hal, Gs To: or wall I-S44-300BYE n
STEP 3 Connect The Wires 1. Connect the neutral (white) wire on the switch to the neutral (white label) wire from the wall. 2. Connect the line (black) wire on the switch to the line (black label) wire from the wall. 3. Connect the load (black) wire on the switch with the load (black label) wire from the wall. Ld NOTE: Both black wires on the switch are Interchangeable and can be connected to either the load or line wire from the wall.
B74 Inch 1. Insert wires info wire nut. = 2. Turn wire nut clockwise. = 3. Pull gently on wires fo lest connection.
STEP 4 Fit Wires Into Wall Box Neatly push the wires back into the box, rotating the switch so it's oriented according to the image.
STEP 5 Secure The Switch Using a Phillips screwdriver and the screws provided, secure the switch fo the wall until level and flush. Then snap the face plate cover onto the bracket.
STEP 6 Turn The Power Back On After the switch is secured and face plate mounted, tum the power back on at the circuit breaker box. At the switch, LED indicator light will flash vibe Indicating the device is wired correctly and the device is in setup mode.
LED Indicator light will continuously flash bite until the switch is added to the C by GE app. LED Indicator light will flash red If the circuit Is overloaded. Max load rating 1.25 amps for LED and 5 amps for Incandescent/halogen. LED Indicator light will not illuminate if wired incorrectly. IF LIGHTS DON'T TURN ON: 1. Check that power to the switch Is on at the breaker. 2.
Congratulations! You've completed the Smart Switch installation. Next...
Enable Your Voice Assistant Cl To seh) the Alex Hiding follow the setup instructions. Salsa, lum off the living room. Salsa, umn on the bedroom. Google Assistant [rigid dpp, starch for the C by SE cation, follow the seize Hay Google, I'm slaving.
Additional Information and Warnings ree Hig TES These limits are lll Lig inn] ee pln the equipment off and on, the user is encourage: mp the Interference by one or more of the pipes) Sabine
ad ll AL CAUTION High Voltage Disconnect power supply le lat lie ei dl epee we als Le ET Type | Enclosure Lr lh nl Impulse Voltage 2500v Gyps 1B action edt ed (DR)
ed be lel te Le TT cuivre d'une température ignominie de 75 °C seulement.