Installation Guide

ManualsBrandsGE ManualsOutdoor FixturesGE EASM & EAMM

Modular Fixtures - Small & Medium (EASM & EAMM)

Evolve

™

LED Area Light

• This luminaire is designed for outdoor lighting service,

and should not be used in areas of limited ventilation,

or in high ambient temperatures.

• Best results will be obtained if installed and maintained

according to the following recommendations.

• Luminaire is designed to operate in ambient

temperatures ranging from -40°C to 50°C and to be

mounted horizontally to a vertical pole with LEDs

facing down, as shown.

Lighting

Installation Guide

GEH-6006A

imagination at work

SPECIFICATIONS

• Weight: Maximum weight <50 lbs (22.68 kg)

• EPA: 1.35 sq ft max (0.13 sq M) (Calculated using

1.30 Cd X Total Area of 1.04 ft

)

• IP Rating: Optical 65, Standard Electrical Enclosure:

UL 1598 Wet Location Rated

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

This Class [A] RFLD complies with the Canadian standard ICES-003.

Ce DEFR de la classe [ A ] est conforme à la NMB-003 du Canada.

Note: This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area

is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

BEFORE YOU BEGIN

Read these instructions completely and carefully.

Save these instructions for future use.

WARNING

Risk of electrical shock. Disconnect power before servicing

or installing product.

CAUTION

Risk of injury. Wear safety glasses and gloves during

installation and servicing.

WARNING

Risk of injury or damage. Unit will fall if not installed

properly. Follow installation instructions.

Summary of content (12 pages)

PAGE 1
GE Installation Guide GEH-6006A Lighting Evolve LED Area Light ™ Modular Fixtures - Small & Medium (EASM & EAMM) BEFORE YOU BEGIN Read these instructions completely and carefully. Save these instructions for future use. WARNING Risk of electrical shock. Disconnect power before servicing or installing product. WARNING Risk of injury or damage. Unit will fall if not installed properly. Follow installation instructions. CAUTION Risk of injury.
PAGE 2
1 UNPACKING • This luminaire has been properly packed so that no parts should have been damaged during transit. • Inspect to confirm. 2 • • HANDLING Damage may occur if luminaire is improperly handled outside of pack. Do not impact or stack luminaire after removal from packaging.
PAGE 3
c Square Pole Architectural Arm Mounting FIXTURE ARM TO ARM ADAPTER This luminaire has been configured the same as 3b and an adapter plate has been included to mount to a square pole. Hole pattern on square pole shall be in accordance with Figure 5. • • • • • • • Orient adapter block so that the end marked top is in the up position. With adapter block end oriented properly, mount adapter block to pole with the nut plate and 3/8-16 bolts and washer supplied as shown.
PAGE 4
PE Dimming Control (If Applicable): • • • No external connections for Dimming are required when the GE Dimming PE Control and GE Dimming PE Receptacle is used. All dimming control connections will be made between the Dimming PE and Luminaire through the included PE Receptacle. Refer to instructions included with GE Dimming PE Control regarding appropriate settings for dimming control.
PAGE 5
GE Guide d’Installation GEH-6006A Lighting Lampadaire à DEL Evolve™ Systèmes d’installation Modulaires – Petit et Moyen (EASM & EAMM) ARRÊT AVANT DE COMMENCER Lisez attentivement toutes ces instructions. Conservez ces instructions pour référence future. AVERTISSEMENT Risque de choc électrique. Déconnectez l’alimentation électrique avant d’installer ou réparer ce produit. AVERTISSEMENT Danger de blessure et de dommage matériel. L’appareil tombera au sol s’il est mal installé.
PAGE 6
1 DÉBALLAGE • Ce lampadaire et été emballé pour qu’aucune pièce ne soit endommagée lors du transport. • Inspecter pour confirmer. 2 MANIPULATION • Des dégâts peuvent se produire si le lampadaire est incorrectement manipulé au dehors de l’emballage. • Ne pas infliger de choc au lampadaire et ne pas superposer les lampadaires après déballage.
PAGE 7
3c Installation par support sur poteau à section carrée GABARIT ET SUPPORT INTERMÉDIAIRE Serrer la vis du haut à 25 - 32 ft-lbs. (34-43 N-m) Ce lampadaire a été configuré de la même manière que 3b et une plaque intermédiaire a été incluse pour installation sur poteau à section carrée. L’arrangement des trous de fixation sur poteau à section carrée doit être conforme à la Figure 5. • Orienter le bloc intermédiaire tel que l’extrémité identifiée par l’inscription ‘haut’ est en position haute.
PAGE 8
GRADATEUR PHOTOÉLECTRIQUE (SI APPLICABLE) : • Aucune connexion externe de gradation n’est nécessaire lorsque la commande de gradateur PE et le réceptacle de gradateur PE de GE sont utilisés. • Toutes les connexions de commande de gradation seront réalisées entre le gradateur PE et le luminaire via le réceptacle PE inclus. • Lire les instructions incluses avec la commande de gradateur PE de GE concernant les réglages appropriés de la commande de gradateur.
PAGE 9
GE Guía de instalación GEH-6006A Lighting Lámpara de LEDs para áreas Evolve ™ Lámparas modulares - pequeñas y medianas (EASM y EAMM) ANTES DE COMENZAR Lea estas instrucciones completamente y cuidadosamente. Guarde estas instrucciones para uso futuro. ADVERTENCIA Riesgo de descarga eléctrica. Desconecte la energía antes de suministrar servicio de mantenimiento o instalar el producto. ADVERTENCIA Riesgo de lesiones o daño. La unidad fallará si no se instala apropiadamente.
PAGE 10
1 DESEMPAQUE • Esta lámpara ha sido empacada apropiadamente de modo que las piezas no deberían sufrir daño durante el transporte. • Inspeccione para confirmar. 2 MANIPULACIÓN • Podría ocurrir daño si la lámpara se manipula inapropiadamente fuera del paquete. • No golpee ni apile la lámpara después de sacarla del embalaje/paquete.
PAGE 11
3c Montaje con brazo arquitectónico en poste cuadrado Esta lámpara tiene la misma configuración del montaje 3b y se incluye una placa adaptadora para montaje en poste cuadrado. El patrón de orificios en el poste cuadrado deberá estar de acuerdo con la Figura 5. • Oriente la placa adaptadora de modo que la parte superior marcada como extremo (“end”) esté en la posición arriba.
PAGE 12
Control fotoeléctrico (PE) de atenuación (si es aplicable): • Cuando se utiliza el Control de atenuación PE de GE y el Receptáculo de atenuación PE de GE, no se necesitan conexiones externas para atenuación. • Todas las conexiones de control de atenuación se harán entre el Control PE de atenuación y la luminaria, a través del Receptáculo de atenuación PE incluido.