- General Electric Computer Accessories User Manual

GEH-6385 Reference and Troubleshooting, 2300 V Drives Index
•
••
•
3
Motor Temperature Estimation, 3-49
Oscillator, 3-4, 3-12
Phase Current Protection, 3-60
Phase Imbalance Monitor, 3-68, 3-69, 3-71, 3-73
Phase Lock Loop, 3-68, 3-69, 3-71, 3-72, 3-73
Position Feedback, 3-4, 3-13
Power Dip Protection, 3-44, 3-49, 3-50, 4-27
Predefined Constants, 3-4, 3-14
Primary Motor & Application Data, 3-21, 4-12, 4-13,
4-15
Remote Speed Reference, 3-83, 3-92, 3-93, 3-98
Sequencer Commands, 3-74, 3-77, 3-79, 3-82, 3-86,
3-91, 3-93, 3-113
Sequencer Overview, 3-74
Sequencer Permissives, 2-5, 2-6, 2-11, 2-15, 2-25, 3-
74, 3-75, 3-76, 3-79, 3-82, 3-85, 3-96
Sequencer Status, 3-74, 3-85, 3-96
Signal Level Detector (SLD), 3-4, 3-15
Simulator, 3-4, 3-18, 3-19, 3-20, 3-30, 4-27, 4-38
Speed Control Fault Check, 3-103
Speed Feedback Calculation, 3-105, 3-106, 3-107, 3-
113, 4-16
Speed Reference Generation, 3-39, 3-40, 3-89, 3-90,
3-91, 3-92, 3-93, 3-94, 3-96, 3-97, 3-98, 3-106, A-
1
Speed Reference Ramp, 3-40, 3-80, 3-81, 3-85, 3-89,
3-94, 3-96, 3-97, 4-17, 4-18, 4-20, 4-21, 4-22, 4-
23, A-1
Speed Reference Reverse, 3-92, 3-94, 3-97, 3-98
Speed/Torque Overview, 3-94, 3-96, 3-106, 3-107
Speed/Torque Regulator, 3-39, 3-40, 3-42, 3-86, 3-94,
3-96, 3-102, 3-107, 3-108, 3-109, 3-110, 4-23, 4-
24, 4-25
Stopping Commands, 2-11
Stopping Commands and Modes, 3-74, 3-76, 3-77, 3-
78, 3-82, 3-85, 3-94, 3-97, 4-19
Tach Loss Detection, 3-50, 3-51, 3-113, 4-16
Timed Overcurrent Detection, 3-61, 3-62, 4-13
Transformer Overtemperature Detection, 3-65
H
Heartbeat, 3-36, 3-37, 3-40, 3-42, 5-4, 5-5, 5-8
I
Inputs
Analog, 3-30, 3-32, 3-48, 3-66, 3-92, 3-93, 4-30, 5-1
Digital, 3-31, 3-33, 3-52, 3-60, 3-65
ISBus, 3-34, 3-35, 3-36, 3-37, 3-38, 5-2, 5-3, 5-4, 5-6
J
Jog, 3-40, 3-42, 3-78, 3-79, 3-82, 3-83, 3-90, 3-91, 3-
92, 3-93, 4-18, 4-19, 4-20, 5-8
K
keypad, 3-1, 3-23, 3-24, 3-25, 3-26, 3-27, 3-28, 3-29, 3-
30, 3-74, 3-78, 3-79, 3-82, 3-85, 3-90, 3-91, 3-93,
3-97, 3-98, 3-111, 4-23, 4-32, 5-1, 5-3
Keypad, 2-2, 3-24, 3-25, 3-26, 3-27
L
LSW1, 4-5, 4-8
M
menu, 3-8, 3-25, 3-29, 4-27
Menu, 3-25, 3-26, 3-28, 3-30
Meter, 3-23, 3-24, 3-25, 3-26, 3-31, 3-32
N
Navigation, 3-24
O
Outputs
Analog, 3-31, 4-10, 4-35
Digital, 3-32, 3-33
P
Parameter Configuration for Signal Mapping, 1-1, 5-3
Parameters
A-B volt fault scale, 3-19
AC grid frequency, 3-73
Accel break point 1, 3-95, 3-96, 4-22, 4-23
Accel break point 2, 3-95, 3-96, 4-22, 4-23
Acceleration rate 1, 3-95, 3-96, 4-21, 4-22
Acceleration rate 2, 3-95, 3-96, 4-21, 4-22
Acceleration rate 3, 3-95, 3-96, 4-22
Adj cur lim ref sel, 3-100, 3-102
Adj gen trq lim sel, 3-100, 3-102
Adj mtr trq lim sel, 3-100, 3-102
Analog in 1 filter, 3-32
Analog in 1 flt lev, 2-23, 3-32
Analog in 1 flt mode, 2-23, 3-32
Analog in 1 gain, 2-23, 3-32
Analog in 1 offset, 2-23, 3-32
Analog in 2 filter, 3-32
Analog in 2 flt lev, 2-24, 3-32
Analog in 2 flt mode, 2-24, 3-32
Analog in 2 gain, 2-24, 3-32
Analog in 2 offset, 2-24, 3-32
Analog meter 1 scale, 3-32
Analog meter 1 sel, 3-32
Analog meter 3 test, 3-31
Analog meter 4 test, 3-31
Analog out 1 offset, 3-32
Analog out 1 scale, 3-32