- General Electric Computer Accessories User Manual

6
•
••
•
Index Innovation Series Meduim Voltage GP – Type G Drives GEH-6385
Run permissive sel, 3-76, 4-19
Run request select, 3-79, 3-82, 4-19, 5-8
Sim A-N volt scale, 3-19
Sim B-N volt scale, 3-19
Sim C-N volt scale, 3-19
Sim const friction, 3-18, 4-27, 4-38
Sim freq slew rate, 3-19
Sim line frequency, 3-19
Sim visc friction, 3-18
Simulate mode, 2-36, 3-18, 3-20, 3-30, 4-7, 4-10
Simulated inertia, 3-18, 4-27, 4-38
Simulated load, 3-18, 4-27
Simulated stiction, 3-18
SLD1 compare mode, 3-15, 3-16, 3-17
SLD1 drop out delay, 3-15, 3-16, 3-17
SLD1 hysteresis, 3-15, 3-16, 3-17
SLD1 input 1 abs val, 3-15, 3-16
SLD1 input 1 select, 3-15, 3-16
SLD1 input 2 select, 3-15, 3-16
SLD1 pick up delay, 3-15, 3-16, 3-17
SLD1 sensitivity, 3-15, 3-16, 3-17
SLD2 compare mode, 3-15
SLD2 drop out delay, 3-15
SLD2 hysteresis, 3-15
SLD2 input 1 abs val, 3-15
SLD2 input 1 select, 3-15
SLD2 input 2 select, 3-15
SLD2 pick up delay, 3-15
SLD2 sensitivity, 3-15
SLD3 compare mode, 3-15
SLD3 drop out delay, 3-15
SLD3 hysteresis, 3-15
SLD3 input 1 abs val, 3-15
SLD3 input 1 select, 3-15
SLD3 input 2 select, 3-15
SLD3 pick up delay, 3-15
SLD3 sensitivity, 3-15
Spd ctl loss delay, 3-104
Spd ctl loss flt lvl, 3-104
Spd fbk display fil, 3-106
Spd reg init val sel, 3-109, 3-110
Spd reg integral gn, 3-109
Spd reg neg err lim, 3-109, 3-110, 3-111, 4-25
Spd reg net gain, 3-108, 3-109
Spd reg pos err lim, 3-109, 3-110, 3-111, 4-25
Spd reg prop cmd gn, 3-109
Spd reg prop fbk gn, 3-109
Spd reg prop filter, 3-109
Speed feedback fil, 3-106
Speed loop sum sel, 3-106, 5-7
Speed setpoint 0, 3-92, 3-93, 4-19
SS relay driver sel, 3-33
SS relay driver test, 3-32
Start permissive sel, 3-76
Starting react Xst, 3-48, 4-15
Stator cold res R1, 3-48, 4-15
Stator hot res R1, 3-48, 4-15
Stator lkg react X1, 3-48, 4-15
Stop PB select, 3-79, 3-82, 4-19
Stop PB select, lan, 3-79, 3-82
Sys ISBus node #, 3-36
Tach loss fault mode, 3-51
Tach speed filter, 3-106
Torque feed fwd sel, 3-108, 3-109, 3-110, 5-7
Torque lim 2 sel, 3-100, 3-102, 4-26, 4-27, 5-9
Torque limit res, 4-25
Torque mode sel, 3-108, 3-109, 3-110, 3-111, 4-24, 5-
8
Torque overload, 4-25
Torque ref select, 3-108, 3-109, 3-110, 4-24, 5-7
Torque reg stop mode, 3-109, 3-111
Transfer mtr req sel, 3-47, 4-28
Type of Cell Test, 4-4
Under freq alarm clr, 3-70, 4-34
Under freq alm level, 3-70, 4-34
Under freq flt level, 3-70, 4-34
Use phase A-B, 4-32
Use phase B-C, 4-32
User NC fault sel, 2-35, 3-52
User NO fault sel, 2-35, 3-52
Utility feed, 3-71, 3-73
Utility phase offset, 4-30
Utility swgr close, 4-29
Utility swgr open, 4-29
Utility volt scale, 4-30
Variable inertia sel, 3-108, 3-109, 3-111
Volt short time, 3-19
X stop mode, 3-81, 4-18
X stop request sel, 3-81, 4-18, 5-8
Xfrmr OT fault mode, 3-65
Xfrmr OT fault sel, 2-34, 3-65
Zero speed delay, 3-85
Zero speed level, 3-42, 3-77, 3-80, 3-81, 3-85, 3-104,
4-17, 4-18
phase leg, 4-5
Phase Lock Loop, 3-68, 3-69, 3-72, 3-73, 5-4
Power Dip Response, 3-44, 3-49, 3-50, 4-27
Power Supplies, 3-103
Processor
DSPXBoard, 2-2, 2-4, 2-5, 2-9, 2-10, 2-16, 2-17, 2-
18, 2-19, 2-21, 2-22, 2-32, 2-33, 2-34, 2-36, 2-37,
2-38, 5-1
Profibus, 3-34, 3-36, 5-2
S
Signal Mapping
Parameter Configuration, 1-1, 5-1
switchgear, 3-47, 4-5, 4-7, 4-8, 4-10, 4-29