- General Electric Computer Accessories User Manual

GEH-6385 Reference and Troubleshooting, 2300 V Drives Index
•
••
•
9
Pos down edge smp, 3-13
Pos up edge sample, 3-13
Position counter, 3-13
Quick stop active, 3-77, 3-85, 4-19
Ramp rate 2 sel, lan, 3-40
Ramp ref enabled, 3-85, 3-94, 3-96
Ready to run, 3-42, 3-75, 3-76, 3-77, 3-78, 3-81, 3-83,
3-84, 3-85, 4-19
Ref enable request, 3-86
Regen torque limit, 3-101
Relay 1 state, 3-33
Relay 2 state, 3-33
Relay 3 state, 3-33
Rev mode req, lan, 3-40, 5-8
Reverse mode active, 3-42, 3-97, 3-98, 5-8
Rotor temp, 3-49
Run active, 3-42, 3-83, 5-8
Run command, 3-83
Run permissive, 3-76, 3-78, 3-79, 4-19
Run ready and fluxed, 3-77, 3-85
Run request, 2-4, 2-5, 2-6, 2-11, 3-40, 3-79, 3-82, 3-
83, 4-18, 4-19, 5-8
Run request, lan, 3-40, 3-79, 3-82, 5-8
Running, 3-33, 3-42, 3-85, 3-86, 4-5, 4-8, 5-8
Sequencer state, 2-3, 3-86
Sim A-B line voltage, 3-20
Sim A-N line voltage, 3-20
Sim B-C line voltage, 3-20
Sim B-N line voltage, 3-20
Sim C-N line voltage, 3-20
Simulate mode act, 2-36, 3-20, 4-7, 4-10
Simulated speed, 3-18, 3-105
SLD1 status, 3-15, 3-16, 3-17
SLD2 status, 3-15
SLD3 status, 3-15
Solid state relay, 3-33
Spd avd func output, 3-89, 3-94
Spd ref offset, lan, 3-39, 5-7
Spd reg integral ref, 3-108
Speed avd func input, 3-89, 3-91
Speed feedback, 3-41, 3-42, 3-94, 3-105, 3-106, 5-7
Speed feedback, lan, 3-41, 5-7
Speed mode active, 3-42, 5-9
Speed ref enabled, 3-75, 3-86, 3-96
Speed ref, pre ramp, 3-89, 3-94, 3-95, 3-96
Speed ref, ramped, 3-85, 3-94, 3-96, 3-106
Speed reference, 3-39, 3-42, 3-85, 3-89, 3-91, 3-94, 3-
97, 3-98, 3-99, 3-110
Speed reg antiwindup, 3-108, 3-111
Speed reg error, 3-104, 3-108, 3-110, 3-111
Speed reg fbk, 3-41, 3-42, 3-50, 3-80, 3-81, 3-85, 3-
94, 3-96, 3-103, 3-104, 3-105, 3-106, 3-107, 3-
108, 3-110, 4-17, 4-18
Speed reg int term, 3-108
Speed reg mode, 3-108, 3-110
Speed reg net gain, 3-108
Speed reg output, 3-108, 3-109, 3-110
Speed reg prop term, 3-108
Speed reg reference, 3-107, 3-108, 3-110
Sqr wave osc output, 3-12
Sreg enable request, 3-86, 3-107
Sreg enable status, 3-75, 3-86
Standby command, 3-83, 3-84
Standby enable req, 3-86
Standby enable stat, 3-86
Start permissive, 3-76, 3-78
Stator temp, 3-49
Stop PB request, 3-79
Stopped, 3-6, 3-8, 3-85, 3-86
Sys ISBus error cnt, 2-37, 3-37, 3-38
Sys ISBus error reg, 2-37, 3-37, 3-38
System fault string, 3-42, 3-55, 3-77, 4-27, 5-8
System fault test, 3-31
Tach speed, 3-51, 3-105, 3-106
Tach speed, instr., 3-51, 3-105
Torque calced, unfil, 3-41
Torque cmd neg limit, 3-101
Torque cmd pos limit, 3-101
Torque ctl neg frz, 3-107, 3-111
Torque ctl pos frz, 3-107, 3-111
Torque current limit, 3-101
Torque current ref, 3-100, 3-101
Torque enable req, 3-86, 3-100, 3-101
Torque fdfwd, lan, 3-39, 5-7
Torque feed forward, 3-39
Torque mode active, 3-42, 5-8
Torque mode req, lan, 3-40, 5-8
Torque ref input, 3-108, 3-109, 3-110, 3-111
Torque ref post lim, 3-99, 3-101
Torque ref pre limit, 3-100, 3-102, 3-108, 3-109, 3-
110
Torque ref, lan, 3-39, 5-7
Torque reg enabled, 3-75, 3-86
Total capture time, 3-5
Transfer MA request, 3-46, 3-47
Transfer motor cmd, 3-47
Transfer motor req, 3-47
Trip fault active, 3-7, 3-42, 3-75, 3-85, 5-8
Trip request, lan, 2-36, 3-40, 5-8
Trq cur ref pre lim, 3-101
Trq lim 2 sel, lan, 3-40
Unused boolean, 3-14
Unused float, 3-14
Unused integer, 3-14
Utility close cmd, 3-47
Utility close status, 3-47
Utility open command, 3-47
Utility open status, 3-47
VCO 1 unfiltered, 3-31
VCO 2 unfiltered, 3-31
VCO 3 unfiltered, 3-31
Voltage offset valid, 3-59