Installation guide

Installation
Instructions
Unitized Electric
Washer/Dryer
Questions on installation? Call: 2-800-GECARES {US} or Visit our Web site at: www.GEAppliunces.com (US).
In Canada, call 800.561.3344 or visit www.GEAppliunces.ca
i
BEFORE YOU BEGIN
Readthese instructions completely and
carefully.
• iMPORTANT- save these instructions for
local inspector's use.
• IMPORTANT- Observeall governing codes
and ordinances.
Note to Installer - Be sure to leave these
instructions with the customer.
Note to Customer- Keepthese instructions with
your Owner's Hanual for future reference.
Beforethe appliance is removed from service or
discarded,remove the washer and dryer doors.
Inspect the dryer exhaust outlet and straighten
the outlet walls if they are bent.
Service information and the wiring diagram are
located at the accesspanel.
Do not allow children on or in the appliance.
Closesupervision of children is necessarywhen
the appliance is used near children.
Install the appliance where the temperature is
above 50°F (10°C)for satisfactory operation of
the control system.
Productfailure due to improper installation is not
coveredunder the Warranty.
A,, ,,, ,.,,,,.,,..
_HLW_KI_I|I_I_" RISK OF FIRE
. To reduce the risk of severe injury or death, follow all installation
instructions.
Appliance installation must be performed by a qualified installer.
Install the appliance according to these instructions and in accordance
with local codes.
This appliance must be exhausted to the outdoors.
Use only 4" rigid metal ducting for exhausting the clothes dryer to the
outdoors.
DO NOT install a clothes dryer with flexible plastic ducting materials.
If flexible metal (semi-rigid or foil-type) duct is installed, it must be
UL listed and installed in accordance with the instructions found
in "Connecting The Dryer To House Vent" on page 8 of this manual.
Flexible venting materials are known to collapse, be easily crushed,
and trap lint. These conditions will obstruct dryer airflow and increase
the risk of fire.
Do not install or store this appliance in any location where it could be
exposed to water and or weather.
Save these instructions. (Installers: Be sure to leave these instructions
with the customer).
NOTE: installation and service of this appliance requires basic
mechanical and electrical skills. It is your responsibility to
contact a qualified installer to make the electrical connections.
4"DIA.METALDUCT
(RECOMMENDED}
MATER
)
4"DUCT
4"DIA.FLEXIBLEMETAL(SEMFRIGID/ CLAMPS(2}
ULLISTEDTRANSITIONDUCT
(iFNEEDED} OR
p
KiTWXOSX10077(IN_LUDES2 ELBOWS} 4"SPRING
CLAMPS(2}
4"DIA.FLEXIBLEMETAL(FOILTYPE}
ULLISTEDTRANSITIONDUCT
kg
(iFNEEDED,}
4"COVERPLATE(iFNEEDED
(KiTWE1M454}
IALS YOU WILL NEED
%
4"DIA.METAL
ELBOW
%
EXHAUST SAFETY
HOOD GLASSES
DUCTTAPE GLOVES
3/4"STRAIN
RELIEF
ULRECOGNIZED
APPLIANCEPOWER
CORDKIT
(NOTPROVIDED}
ULRATED
120/240V,30A
WITH3OR4 PRONGS.
IDENTIFYTHEPLUG
TYPEASPERTHE
HOUSERECEPTACLE
BEFOREPURCHASING
LINECORD,
PARTS SUPPLIED
2 Rubber 2 Stainer Screens/
1 Cable Tie Washers Rubber Washers
(washers may be in water hoses)
2 Washer Hoses
TOOLS YOU WILL NEED
Slip Pliers
Phillips Screwdriver
Flot-blode Screwd river
1/4" Nutdriver
Level
233D1835PO04
31-16728 12-14 GE PrintedinMexico