Manual

Optional Control Settings
The controller display has sexeral options and teatm'es.
LOW SALT ALARM I?__&_
The LOW SALTALARM, when enabled, _ nwill somM the beeper when the DAYS _ 4_)1 LIm
TO EMPTYxalue is 15 da_s or less, To
chanoe,_ this setting,, press and hold the MODEbutton for
3 seconds. ON (e_ctorv default) or OFF will flash in the
display., Press the UP _ or DOX4N • buttons to togole,
this feature ON or OFF. Press the MODE button to accept,
aim the displa)will n/oxe to SALT EFFICIENCY.
SALTEFFICIENCY SALT
.EVEL
_4hen the SALTEFFICIENCYfeamre n
is ON, the refit will operate at a salt __ LII-I_ _
efficiency of at least 4000 grains of
hardness remoxed per p(mnd of salt. This mode of
operation is the most efficient setting for salt usa ,e
because the sxsteln will tend to recharge, more often,
with less salt usa. _,e Turning, the feature OFF will tend
to lengthen the time between recharge cycles which will
proxide the most etticient usage of water, but max use
more salt. The degree of difference between these
two c_cles is highly dependent on the water usage and
hardness at a particular installation.
If you haxe xer_ hard water and you find your sxstem
is reoenerating exerv 1-2 days turn the SALT EFFICIENCY
to OFF to lengthen the time between regenerations.
NOTE: California Regulations require this feature to be
ON for installations in Califl)rnia.
To chan,,e_ the setting,, press the UP • or DO_N •
buttons to toggle the feature ON or OFF. Press the
MODE button to accept. The displa)will moxe to
SYSTEM/ELECTRONICDIAGNOSTICS.
SYSTEM/ELECTRONICDIAGNOSTICS
This display contains s):stem
diagnostics inflmnation to assist in
troul)leshooting problems with the
system. See pages 15-18 tot details.
Press the MODEbutton to return to
the normal mn display.
SALT
.EVaL
n n
u u
nnn
UUU
GEAppliances.com
LOST TIME SIGNAL
If time is lost on the displa) due to power interruption, the
blue indicator light will flash 4 times exerx second, tmtil the
present time of day is entered.
LOW SALT SIGNAL
When the DAYS TO EMPTY drops to 15, the blue indicator
light and DAYS TO EMPTYin the display will flash every
second and the alarm will beep every 30 seconds (fl'om
8:00 AM to 8:00 PM), to notitV the user that the unit is
_tmning low on salt. As soon as any button is pressed,
the alam/will stop beeping. The bhm indicator light and
DAYS TOEMPTYwill continue to flash. Once salt is added
to the brine tank and the SALTLEVEL is reset, the DAYS TO
EMPTYwill be reset.
ERRORSIGNALS
If there is an error code detected, the I
blue indicator light will flash 4 times I
every second, the display will flash Err
and the alarm will beep every 30 seconds (fl'om 8:00 AM
to 8:00 PM), to signal that the softener requires service.
The alarm can be turned off by pressing any button, but
the blue indicator light and display will continue to flash.
See page 16 for inflmnation to assist in tr(mbleshooting
error codes. Once the problem is corrected, disconnect the
transfl)rmer fl'om the wall outlet momentarily, and I)lug it
back in. The normal display will appear. The motor may
um tOT several minutes, as the trait resets. If the problem is
not corrected, the error code will real)pear in 6 minutes.
BLUE INDICATOR LIGHT
Steady blue light indicates that the trait is working
correctly. The light flashes when the trait needs attention
from the user.
• i,ight flashes and DAYS TO EMPTYflashes--check salt lexel
and add salt as required.
• I,ight flashes and Err is in the displa)--electrical problem
with system--see page 16.
• I,ight will also flash when power to the trait has been
interrupted. Check the PRESENT TlME setting.
11