Installation Guide

ManualsBrandsGE ManualsAppliances30 in. 5 cu. ft. Free-Standing Gas Range in Slate

TOOLS YOU WILL NEED MATERIALS YOU MAY NEED

 Gas line shut-off valve

 Pipe joint sealant or UL-approved pipe thread

tape with Teflon* that resists action of natural

and propane gases.

 Flexible metal appliance connector (1/2” I.D.).

A 5-foot length is recommended for ease of

installation but other lengths are acceptable.

Never use an old connector when installing a

new range.

 Flare union adapter for connection to gas

supply line (3/4” or 1/2” NPT x 1/2” I.D.).

 Flare union adapter for connection to pressure

regulator on range (1/2” NPT x 1/2” I.D.)

 Liquid leak detector or soapy water.

*Teflon: Registered trademark of DuPont

Flat-blade

screwdriver

Pipe wrenches (2)

(one for backup)

Phillips

screwdriver

Open-end or

adjustable wrench

Pencil and ruler

Level

Drill, awl or nail

IN THE COMMONWEALTH OF

MASSACHUSETTS

 This product must be installed by a licensed

plumber or gas fitter.

 When using ball type gas shut-off valves, they

shall be the T-handle type.

 A flexible gas connector, when used, must not

exceed 3 feet.

Installation Instructions

Range

Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com

BEFORE YOU BEGIN

,03257$17³

Save these instructions for

local inspector’s use.

,03257$17³ Observe all governing

codes and ordinances.

,03257$17³ Remove all packing

material and literature from oven before

connecting gas and electrical supply to range.

,03257$17³ To avoid damage to your

cabinets, check with your builder or cabinet

supplier to make sure that the materials used will

not discolor, delaminate or sustain other damage.

This oven has been designed in accordance with

the requirements of UL and CSA International

and complies with the maximum allowable wood

cabinet temperatures of 194°F (90°C).

Note to Installer – Be sure to leave these

instructions with consumer.

Note to consumer – Keep these instructions for

future reference.

Servicer – The electrical diagram is in an

envelope attached to the back of the range.

Proper installation is the responsibility of the

installer.

Product failure due to improper installation is not

covered under warranty.

Before installing your range on linoleum or any

other synthetic floor covering, make sure the

floor covering can withstand 180°F without

shrinking, warping or discoloring. Do not install

the range over carpeting unless a sheet of 1/4”

thick plywood or similar insulator is placed

between the range and carpeting.

Mobile Home - Additional Installation

Requirements

The installation of this range must conform to

the Manufactured Home Construction and Safety

Standard, Title 24 CFR, Part 3280 (formerly the

Federal Standard for Mobile Home Construction

and Saftey, Title 24, HUD Part 280). When such

standard is not applicable, use the Standard for

Manufactured Home Installations, ANSI A225.1/

NFPA 501A or with local codes.

In Canada, the installation of this range must

conform with the current standards CAN/CSA-

A240-latest edition, or with local codes.

When this range is installed in a mobile home, it

must be secured to the floor during transit. Any

method of securing the range is adequate as

long as it conforms to the standards listed above.

WARNING

FIRE OR EXPLOSION HAZARD

If the information in this manual is not followed

exactly, a fire or explosion may result causing

property damage, personal injury or death.

Installation must be performed by a qualified

installer.

Read these instructions completely and carefully.

Installation of this range must conform with

local codes, or in the absence of local codes,

with the National Fuel Gas Code, ANSI Z223.1/

NFPA.54, latest edition. In Canada, installation

must conform with the current Natural Gas

Installation Code, CAN/CGA-B149.1 or the current

Propane Installation Code, CAN/CGA-B149.2, and

with local codes where applicable. This range

has been design-certified by CSA International

according to ANSI Z21.1, latest edition and

Canadian Gas Association according to CAN/

CGA-1.1 latest edition.

When installing a gas appliance the use of old

flexible connectors can cause gas leaks and

personal injury. Always use a NEW flexible

connector.

Leak testing of the appliance shall be conducted

according to the manufacturer instructions.

The range must be electrically grounded in

accordance with local codes or, in the absence

of local codes, in accordance with the National

Electrical Code (ANSI/NFPA 70, latest edition).

In Canada, electrical grounding must be in

accordance with the current CSA C22.1 Canadian

Electrical Code Part 1 and/or local codes. See

Electrical Connections in this section.

Do not install this product with an air curtain

hood or other range hood that operates by

blowing air down on the cooktop. This airflow

may interfere with operation of the gas burners

resulting in fire or explosion hazard.

FOR YOUR SAFETY:

• A child or adult can tip the range and be killed.

• Install the anti-tip bracket to the wall or floor.

• Engage the range to the anti-tip bracket by sliding the

range back such that the foot is engaged.

• Re-engage the anti-tip bracket if the range is moved.

• Failure to do so can result in death or serious burns

to children or adults.

Tip-Over Hazard

WARNING

Before beginning

the installation, switch power off at

service panel and lock the service

disconnecting means to prevent power

from being switched on accidentally.

When the service disconnecting means

cannot be locked, securely fasten a

prominent warning device, such as a

tag, to the service panel.

If you did not receive an anti-tip bracket with your

purchase, call 1.800.626.8774 to receive one at no

cost. (In Canada, call 1.800.561.3344.) For installation

instructions of the bracket, visit: www.GEAppliances.com.

(In Canada, www.GEAppliances.ca.)

Anti-Tip Bracket

Kit Included

Summary of content (8 pages)

PAGE 1
Installation Instructions Range TOOLS YOU WILL NEED Phillips screwdriver Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com IN THE COMMONWEALTH OF MASSACHUSETTS This product must be installed by a licensed plumber or gas fitter. When using ball type gas shut-off valves, they shall be the T-handle type. A flexible gas connector, when used, must not exceed 3 feet.
PAGE 2
DIMENSIONS AND CLEARANCES Provide adequate clearances between the range and adjacent combustible surfaces. These dimensions must be met for safe use of your range. Allow 30” (76.2 cm) minimum clearance between burners and bottom of unprotected wood or metal cabinet, or allow a 24” (61 cm) minimum when bottom of wood or metal cabinet is protected by no less than 1/4” (6.4 mm) thick flame-retardant millboard covered with no less than No. 28 MSG sheet metal (.015” [.38 mm] thick), .015” (.
PAGE 3
To prevent gas leaks, put pipe joint compound on, or wrap pipe thread tape with Teflon* around, all male (external) pipe threads. 1 GAS SUPPLY WARNING Fire Hazard: Do not use a flame to check for gas leaks. WARNING Explosion Hazard: Do not exceed 25 ft-lbs of torque when making gas line connections. Overtightening may crack the pressure regulator resulting in fire or explosion hazard. Gas Pressure Regulator You must use the gas pressure regulator supplied with this range.
PAGE 4
CHECK SURFACE BURNERS Push and turn knob to LITE position. You will hear a clicking sound indicating proper operation of the spark module. Once the air has been purged from the supply lines, burners should light within 4 seconds. After burner lights, rotate knob out of the LITE position. Try each burner in succession until all burners have been checked. Quality of Flames The flame quality of the burners needs to be determined visually. If burner flames look like (A), call for service.
PAGE 5
Instrucciones de Instalación Cocina Ante cualquier duda, llame al 1.800-GE-CARES o visite nuestro sitio web en: HERRAMIENTAS NECESARIAS Destornillador Philips GEAppliances.com En el Commonwealth de Massachusetts • Este producto debe ser instalado por un plomero licenciado o un mecánico gasista. ADVERTENCIA RIESGO DE INCENDIO O EXPLOSIÓN Si la información de este manual no se sigue exactamente, se podrá producir un incendio o explosión, ocasionando daños sobre la propiedad, lesiones o la muerte.
PAGE 6
DIMENSIONES Y ESPACIOS de grosor), .015” (.38 mm) de grosor de acero inoxidable, .025” (0.64 mm) de aluminio o .020” (0.5 mm) de cobre. Deje el espacio adecuado entre la cocina y las superficies combustibles adyacentes. Estas dimensiones se deberán cumplir para un uso seguro de su cocina. Deje un espacio mínimo de 30” (76.
PAGE 7
1 SUMINISTRO DE GAS ADVERTENCIA Riesgo de incendio: No use una llama para controlar las pérdidas de gas. ADVERTENCIA Riesgo de Explosión: No supere una torsión máxima de 25 pieslibras al realizar conexiones de tuberías de gas. Cualquier ajuste en exceso podrá romper el regulador de presión, resultando en riesgo de incendio o explosión. Regulador de Presión de Gas Se deberá usar el regulador de presión de gas suministrado con esta cocina.
PAGE 8
4 CONTROLE LAS CABEZAS DE LOS QUEMADORES Presione y gire la perilla a la posición LITE (Luz). Escuchará un sonido de clic, que indica el funcionamiento adecuado del módulo de chispeo. Una vez que el aire se haya purgado de las líneas de suministro, los quemadores se deberán encender dentro de los 4 segundos. Luego de que los quemadores se iluminen, gire la perilla fuera de la posición LITE. Pruebe cada quemador de forma sucesiva hasta que todos los quemadores hayan sido controlados.