Installation instructions

ManualsBrandsGE ManualsDomestic AppliancesJGGR24LPDBB

Questions? Call 866.GE.GRILL (866.434.7455)

or Visit our Website at:

www.GEAppliances.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS

Assembly Outdoor Cooking

Instructions Center

Read these instructions completely and carefully.

•

IMPORTANT

–

Observe all

governing codes and ordinances.

• Note to Assembler

–

Be sure to leave these

instructions with the Consumer.

• Note to Consumer

–

Keep these

instructions for future reference.

• Skill level – Assembly of this grill requires basic

mechanical skills.

BEFORE YOU BEGIN

• Proper assembly is the responsibility of the assembler.

• Product failure due to improper assembly is not

covered under the Warranty.

• If you received a damaged grill, you should contact

your dealer.

• Note

–

Grill must be completely assembled before

any gas connections are made.

TOOLS YOU WILL NEED

Phillips screwdriver

7/16″ open end wrench or deep socket with extension

Rubber mallet (optional)

JGGN24, JGGR24

Block of wood or cardboard

(optional)

Summary of content (16 pages)

PAGE 1
Assembly Instructions Outdoor Cooking Center JGGN24, JGGR24 Questions? Call 866.GE.GRILL (866.434.7455) or Visit our Website at: www.GEAppliances.com BEFORE YOU BEGIN • Proper assembly is the responsibility of the assembler. • Product failure due to improper assembly is not covered under the Warranty. • If you received a damaged grill, you should contact your dealer. • Note – Grill must be completely assembled before any gas connections are made. Read these instructions completely and carefully.
PAGE 2
Assembly Instructions PARTS INCLUDED (Not all models have all parts) Handle with Spacer (2) Grill Body (1) Base Assembly (1) Handle Nut (2) Bin (1) Handle Bolt (2) Upper Rear Brace (1) Shelf Handle (1) Grease Cup Holder (1) Thumb Screw (2) Side Grid (1) Screw (2) Large Bolt (8) Wing Nut (19) Left Side Burner/Shelf (1) or Side Shelf (1 or 2) (Depending on model) Carriage Bolt (2) Rotisserie Burner (1) (On some models) Front Banner (1) Retractable Shelf (1) Wheel (2) Wheel Clip (2) Large Wh
PAGE 3
Assembly Instructions 4. Grasp the pan on both sides and raise it up until the legs are standing squarely on the floor. NOTE TO ASSEMBLER To aid assembly, all parts in bold type in the following assembly steps match the illustrations shown in the PARTS INCLUDED section. 1 UNPACK THE GRILL • Carefully cut open the box, remove the contents and group like parts together. 2 UNFOLD THE BASE ASSEMBLY 1. Make sure the open side of the pan in the base assembly is facing up.
PAGE 4
Assembly Instructions 3. Slide a wheel axle bolt through a wheel, large wheel washer, and through the top hole on the left leg. Secure the wheel in place by sliding a wheel clip through the hole in the wheel axle bolt. Repeat for the other leg. 3 ASSEMBLE THE LOWER BASE Thumb Screw (2) Carriage Bolt (2) Wing Nut (4) Wheel Axle Bolt (2) Wheel Wheel Clip (2) Large Wheel Washer (2) 1. Thread a thumb screw into each of the lower holes on the right side and through the pan.
PAGE 5
Assembly Instructions 4. Thread a large bolt into the front bottom hole on each side. Secure in place with wing nuts. 4 ASSEMBLE BASE TO GRILL BODY Large Bolts Wing Nuts Wing Nut (10) Large Bolt (6) 1. Turn the grill body upside-down and wedge cardboard or a block of wood under the front side to prevent tipping during assembly. 2. Slide the bolt on each of the back legs into the slots on the back ends of the grill. Secure in place with wing nuts. Upper Rear Brace 3.
PAGE 6
Assembly Instructions 6 INSTALL THE HANDLES Handle Bolt (2) 8 INSTALL THE SIDE SHELVES Handle Nut (2) • Slide a handle bolt through a handle and spacer and into the hole in the grill top. Align and tighten in place with a handle nut using a 7/16″ open end wrench or deep socket. Repeat for the other side. Large Bolt (1 or 2) Wing Nut (1 or 2) NOTE: If your model has a burner/shelf, it must be installed on the left side. 1. Peel off the protective shipping film from the side shelves, if present. 2.
PAGE 7
Assembly Instructions 9 INSTALL THE LEFT SIDE BURNER/SHELF (on some models) 4. Remove the side grid and peel off the protective shipping film, if present. Guide the two pins on the grid into the two holes in the side burner/shelf and lower it into position. Side Grid Screw (2) Large Bolt (1) Wing Nut (1) 1. Peel off the protective shipping film from the side shelves, if present. 5.
PAGE 8
Assembly Instructions 3. Hand connect the side burner electrode wire to the connector under the control panel. (The connector is under the control panel, on the stem of the red igniter button). 10 CONNECT THE LEFT SIDE BURNER/SHELF (on some models) 1. Connect the side burner hose by pressing the fitting onto the side burner gas tube. Side Burner Gas Tube Side Burner Hose Fitting Make a firm connection Make side burner gas connection 2.
PAGE 9
Assembly Instructions 11 ASSEMBLE THE GRILL COMPARTMENT 3. With the deflector on top (holes facing front), press the round end of the rotisserie burner (on some models) into the hole on the right. Press down and snap the left side into the two holes in the left side of the grill. 1. Place the Flav-R-Wave® on the supports in the bottom of the grill. The Flav-R-Wave® should lie flat. Flav-R-Wave® Rotissere burner 2. Place the side-by-side grids on the front and back supports*. 4.
PAGE 10
Assembly Instructions 12 INSTALL THE FRONT BANNER 14 MOUNT THE LP TANK (not included—obtain locally) NEW OPD HANDWHEEL QCC1¤ N E OS CL • Your grill is designed to be used with an LP gas tank equipped with the new QCC-1 Quick Closing Coupling system and the new OPD handwheel. OPE 1. Insert the pointed support of the front banner into the slot behind the front leg at the base. L P- G A S OP D LP tank valve • The QCC-1 system is recognizable by the external threads on the inlet port of the valve.
PAGE 11
Assembly Instructions 15 CONNECT THE LP TANK TEST FOR LEAKS (CONTINUED) 1. Remove the plastic cover from the LP tank connector. 5. Wet each connection with the soap solution. 2. Screw the regulator coupling (on the gas hose) onto the LP tank connector in a clockwise direction. Hand tighten only. LP Tank Connection LP Tank Connector 6. A leak is identified by a flow of bubbles from the area of the leak. Regulator Coupling 7.
PAGE 12
PARTS LIST 12
PAGE 13
GENERAL ELECTRIC PARTS CATALOG REF. NO. 1. 2. 3. 5. 6. 7. 9. 11. 14. 15. 17. 18. 21. 21A. 21B. 22. 23. 30. 31. 32. 33. 35. 36. 37. 38. 39. 40. 46. 49. 50. 53 54. 55. 56. 57. 65. 68. PART NO.
PAGE 14
GENERAL ELECTRIC PARTS CATALOG (cont.) REF. NO. 74. 75. 76. 77. 78. 79. 80. 81. 82. 83. 84. 85. 86. 87. 88. 89. 93. 96. 97. 98. 99. 101. 104. 105. 108. 109. 110. 111. 113. 114. 115. 117. 118. 123. PART NO.
PAGE 15
NOTES 15
PAGE 16
Part No. 164D4290P034 Pub. No.