Installation guide

ManualsBrandsGE Manualswall ovenOfficial GE wall oven

Installation

Instructions

27" Built-In Wall Oven

JKP20, JKP28, JKP48, JK915, JK955, JKS06,

ZEK938, ZEK958

If you have questions, call 1.800.GE.CARES or visit our website at:

www.GEAppliances.com

Before You Begin

Read these instructions carefully and completely.

• IMPORTANT-save these

instructions for local inspector's use.

• IMPORTANT-observe all

governing codes and ordinances.

• Note to InstallermBe sure to leave these

instructions with the consumer.

• Note to ConsumermKeep these

instructions for future reference.

• Proper installation is the responsibility

of the installer and product failure due

to improper installation is NOT covered

under warranty.

• NOTE_This appliance must be properly

grounded.

• ATTENTION INSTALLER

All electric wall ovens must be hard wired

(direct wired) into an approved junction

box. A plug and receptacle is NOT permitted

on these products.

Parts Included

Single Ovens

8 Screws

Double Ovens

12 Screws

Metal

Bottom Trim

Plastic

Bottom Trim

Metal Bottom Trim

Optional

Metal Bottom Trim

Assembly

Materials Needed

Strain Relief Clamp

for 1/2" conduit

_ WireNu_s

Junction

Box ,_

36" of String

Tools You Will Need

1/8" Drill Bit and

Electric or Hand Drill

Phillips

Screwdriver

229c4053P504

31-10523 (06-02 JR)

Summary of content (16 pages)

PAGE 1
Installation Instructions 27" Built-In Wall Oven JKP20, JKP28, JKP48, JK915, JK955, JKS06, ZEK938, ZEK958 If you have questions, call 1.800.GE.CARES www.GEAppliances.com Before You Begin Read these instructions carefully and completely. • IMPORTANT-save instructions these for local inspector's • IMPORTANT-observe use. all governing codes and ordinances. • Note to InstallermBe sure to leave these instructions with the consumer.
PAGE 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical Requirements For Your Safety • Be sure your oven is installed properly by a qualified installer or service technician. This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating Plate is located on oven side trim.
PAGE 3
Installation Instructions Pre-lnstallation Checklist Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: Open the oven door as far as it will go. Remove packaging materials. Check behind hinges and under false bottom. Remove labels on the outside of the door, plastic on trims and panel and all tape around oven. Push both hinge locks down toward _,,,,_ the door frame, Hinge" _"'_ to the unlocked S_ot position.
PAGE 4
Installation Instructions I_ Pre-lnstallation [_ lace the oven on a table or platform even with the cutout opening. (Platform must support 150 Ibs. single, 275 Ibs. double.) Checklist cont. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top of the unit.
PAGE 5
Installation Instructions Cutout for Single Built-In Oven Width Cabinet 27" Allow 7/8" for overlap of oven over side edges of Cutout Width 25" iin. _L / or runners Width 27" Recommended Minimum Cutout Location from Floor 32 1/2" Cutout Depth 23 1/2" Min. Cutout Width 25" Min. } 22" Min. above base rail utout 2"x4" Cabinet Junction Box Location i Height I 27 5/8" Min. I 28 1/8" Max. I 25 1/4" Max. 27 5/8" Min. Cutout Height I 28 1/8" Max.
PAGE 6
Installation Instructions Cutout for Double Built-In Oven Cabinet Junction Box Location -- Allow 7/8" for Width Cabinet 27" ___ Cutout it" Width 25" Min. 25 1/4" Max. overlap of oven over side edges of cutout ----...._ Width Recommended Minimum Cutout Location from Floor 13 1/4" Cutout Depth 23 5/8" Min. Cutout Width 25" Min. 25 1/4" Max. Above base rail Cutout Height Cutout Height 49 11116" Min. 50 118" Max. 49 11/16" Min. 50 1/8" Max.
PAGE 7
Installation Instructions I_ Cutout for Single Built-In Oven Under Counter Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. \ 240V / 208V Junction Box Location / 25" Top and/or side fillers may be necessary if unit is positioned between existing cabinets. Be sure they are attached securely, since they will anchor the oven in the cabinet.
PAGE 8
Installation Instructions Electrical Connections ATTENTION Turn off the circuit breaker or remove fuses to the oven branch circuit. INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below.
PAGE 9
Installation Instructions Electrical Connections cont. New Construction and Four-Conductor Branch Circuit Connection • When installing in new construction, ° When installing in a mobile home, or ° When installing in a recreational Three-Conductor Branch Circuit Connection When connecting to a three-conductor circuit, if local codes permit: or vehicle, branch a.
PAGE 10
Installation Instructions [c-]Securing the Oven in the Opening [_ Sliding the Oven Into the Opening Drilling the Pilot Holes and Mounting the Oven a. Loop (do not tie) a 36" string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered. a.
PAGE 11
Installation Instructions To install a single metal bottom trim assembly (on some models), use sections C3 and C4. To install a metal bottom trim with a plastic bottom trim (on some models), use sections C3-C5. Preparing for the Bottom Trim Installation a. b. c. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. Using the trim as a template, mark the center of each slot (two total) where the mounting holes will be drilled.
PAGE 12
Installation Instructions Replacing the Oven Door NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. -_ -_ pen the oven door as far as it will open. -_ Push the hinge locks up against the front frame of the oven cavity, to the locked position. Hinge in Locked Position ift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle.
PAGE 13
Installation Instructions Pre-Test Checklist Remove all protective and any stickers. film, if present, Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see page 11). [_ Check to be sure the mounting screws are installed and flush with the side trim (see page 10). Operation Checklist Remove all items from the inside of the oven.
PAGE 14
NOTES 14
PAGE 15
NOTES 15
PAGE 16
NOTES 16