Built-In Wall Oven 27" (68.6 cm) models JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958 Ilnstallat!on nstruct=ons 30" (76.2 cm) models JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 If you have questions, call 1.800.GE.CARES ge.com Before You Begin Read these instructions carefully and completely. • IMPORTANT-save instructions these for local inspector's • IMPORTANT-observe use. all governing codes and ordinances.
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety Electrical • Be sure your oven is installed properly by a qualified installer or service technician. Requirements • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door.
Installation Instructions Pre-lnstallation Checklist Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES IS TO BE USED FOR SINGLEAND DOUBLE OVEN INSTALLATION! Open the oven door as far as it will go. i Remove packaging materials. Check behind hinges and under false bottom.
Installation Instructions Cutout for 27"(68.6cm)Single Ovens only Built-In For JKS10, JKP30, JKP70, PK916, ZEK938 models only. Cabinet 5" (12.7 cm) Max. from the left or right Cabinet --Width _ side l Cutout Allow 1" (2.5 cm) for overlap of oven over side edges of cutout Cutout Width 25" (63.5 cm) Min. Cutout Width _" Max. 20" (50.8 cm) _joJ-" j-- 7- of 20" (50.8 cm) for clearance to adjacent corners, drawers, walls, etc. when door is open Cutout Height 22" (55.9 cm) 27 5/8" Min. above (70.
Installation Instructions Cutoutfor 27"(68.6 Ovensonly DoubleBuilt-In For JKP35, JKP55, JKP75, PK956, ZEK958 models only. 6" (12.7 cm) Max. from the left or Cabinet right (68.6 cm) Cutout Allow 1" (2.6 cm) for overlap of over over side i Junction Box _F._ (63.5 cm) Men. 25 1/4" i (64.1 cm) Ma_. Cabinet Width 27" (68.6 cm) Recommended Cutout Location from Floor 13 1/4" (33.7 cm) Cutout Depth 23 5/8" (60 cm) Men. Cutout Width 25" (63.5 cm) Men. Location iii zzI 25 1/4" (64.1 cm) Max.
Installation Instructions IAICutout for 27" (68.6cm)Single Built-In Ovens only Under Counter For JKS10, JKP30, JKP70, PK916, ZEK938 models only. Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size, See label on top of oven for approved cooktop models. 240V / 208V Junction Box Location 25" (63.5 cm) \. \\ 5" (12.7 cm) Max.
Cabinetry Cutout for 27" (68.6cm)Single or Double Built-In Ovens only- Over a Warming Drawer For JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958 models only. Single 27" (68.6 cm) Double 27" (68.6 cm) Oven Over a Warming Drawer Oven Over a Warming Drawer Anti-Tip Block Against Rear •Wall Per Warming Drawer Requirement Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement 3" (7.6 cm) Min, 3" (7.6 cm) Min.
Cabinetry Cutout for 27" (68.6cm)Single Ovens only- Below an Advantium or Between an Advantium and a Warming Drawer For JKS10, JKP30, JKP70, PK916, ZEK938 models only. Single 27" (68.6 cm) Oven Below an Advantium Per Advantium Requirement Single 27" (68.6 cm) Oven Between an Advantium and a Warming Drawer Per AdvantiL Requirement 3" (7.6 cm) Min. Note: Install the oven only with specific models listed on the label located on top of the oven.
Installation Instructions Cutout for 30"(76.2 Ovens only Built-In cm)Single For JTP30, JTP70, PT916, PT920, ZET938 models only. Cutout Width 28 1/2" (72.4 cm) Min. _ 28 5/8" (72.7 cm). Max. Allow 11/16" (1.75 cm) for overlap of oven over side edges of cutout ---- Between 7 3/4" (19.7 cm) Max. Junction Box Location (junction box may be located in / ___ IN cutout I Recommended Cutout Location from Floor 32 1/2" (82.6 cm) Cutout Depth 23 1/2" (69.7 cm) Min. Cutout Width 28 1/2" (72.4 cm) Min.
Installation Instructions IAICutoutfor30' 6.2cm)Double Built-InOvensonly For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models only. Cutout Width 28 112" (72.4 cm) Min, 28 518" (72.7 cm) ==: Max. 7 3/4" (19.7 cm Junction Box ) Location (junction box may be located in adjacent cabinet) I / Allow 11/16" (1.75 cm) for overlap of oven over side edges of cutout Allow a minimum of 21" (53.
Installation Instructions IAICutout for 30" (76.2cm) Single Built-InOvens only Under Counter For JTP30, JTP70, PT916, PT920, ZET938 Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. models only. 240V / 208V Junction Box ,\ Location (junction box may be in adjacent cabinet) 7 3/4" 25" (63.5 cm) (19.7 cm) \_ Top and/or side fillers may be necessary if unit is positioned between existin
Cabinetry Cutout for 30"(76.2cm) Single or Double Built-In Ovens only- Over a Warming Drawer For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 models only. Double 30" (76.2 cm) Oven Over a Warming Drawer Single 30" (76.2 cm) Oven Over a Warming Drawer Block Against Rear Wall Per Warming Drawer Requirement Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement 2" (5.1 cm) Min. NOTE: install the 2" (5.1 cm) Min.
Cabinetry IAICutoutfor 30"(76.2 cm) Single Ovens only Below an Advantium or Betweenan Advantium and a Warming Drawer For JTP30, JTP70, PT916, PT920, ZET938 Single 30" (76.2 cm) Oven Below an Advantium models only. Single 30" (76.2 cm) Oven Between an Advantium and a Warming Drawer Requirement Per Advantiu Requirement 3" (7.6 cm) Min. 3" (7.6 cm) Min. 2" (5.1 cm) Min. Note: Install the oven only with specific models listed on the label located on top of the oven.
Installation Instructions Electrical Connections ATTENTION Turn off the circuit breaker or remove fuses to the oven branch circuit. INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below.
Installation Instructions New Construction and Four-Conductor Branch Circuit Connection • When installing in new construction, • When installing in a mobile home, or • When installing in a recreational Three-Conductor Branch Circuit Connection When connecting to a three-conductor circuit, if local codes permit: or vehicle, branch a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
Installation Instructions lcl Securing the Oven in the Opening I_ Sliding the Oven Into the Drilling the Pilot Holes and Mounting the Oven Opening a. Loop (do not tie) a 36" (91 cm) string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered.
Installation Instructions Installing the Metal Bottom Trim Preparing for the Bottom Trim Installation a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. b. Using the trim as a template, mark the center of each slot (two total) where the mounting holes will be drilled. c. Remove the trim. d. Drill pilot holes into the center of each template mark. a. For 27" (68.6 cm) Place the bottom metal trim centered over the pre-drilled mounting holes.
Installation Instructions 151Replacing the Oven Door NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. I-_ Open the oven door as far as it will open. r-_ Push the hinge locks up against the front frame of the oven cavity, to the locked position. i Hinge in Locked Position Lift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle.
Installation Instructions Pre-Test Checklist I_ emove all protective and any stickers. I_ heck to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see page 17). film, if present, Check to be sure the mounting screws are installed and flush with the side trim (see page 16). t Operation Checklist Remove all items from the inside of the oven. I&_ Check that conduit is securely connected to the junction box.
Notes 20
