Installation guide

ManualsBrandsGE ManualsWall oven/microwave comboOfficial GE oven/microwave combo

Installation

Instructions

27" Built-In Wall Oven

with Microwave

JKP86

If you have questions, call 1.800.GE.CARES or visit our website at:

www.GEAppliances.com

Before You Begin

Read these instructions carefully and completely.

• IMPORTANT-save these

instructions for local inspector's use.

• IMPORTANT-observe a,

governing codes and ordinances.

• Note to Installer--Be sure to leave these

instructions with the consumer.

• Note to ConsumermKeep these

instructions for future reference,

• Proper installation is the responsibility

of the installer and product failure due

to improper installation is NOT covered

under warranty.

• NOTE--This appliance must be properly

grounded.

• ATTENTION INSTALLER

All electric wall ovens must be hard wired

(direct wired) into an approved junction

box. A plug and receptacle is NOT permitted

on these products.

Parts Included

Screws For Installation Metal Bottom Trim

Tools Needed

1/8" Drill Bit and

Electric or Hand Drill

Phillips

Screwdriver

Materials Needed

__ @ Wireaunts

Strain Relief Clamp Junction

for 1/2" conduit Box €%-_'_-,,

36" of String

229c4053P507-3

31-10526-3 o6-o3JR

Summary of content (12 pages)

PAGE 1
Installation Instructions 27" Built-In Wall Oven with Microwave JKP86 If you have questions, call 1.800.GE.CARES or visit our website at: www.GEAppliances.com Before You Begin Read these instructions carefully and completely. • IMPORTANT-save instructions these for local inspector's use. • IMPORTANT-observe a, governing codes and ordinances. • Note to Installer--Be sure to leave these instructions with the consumer.
PAGE 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical Requirements For Your Safety • Be sure your oven is installed properly by a qualified installer or service technician. This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating plate is located on the inside wall of the microwave oven.
PAGE 3
Installation Instructions Pre-lnstallation Checklist Remove packaging materials. Check inside microwave, behind hinges and under false bottom. Remove labels on the outside of the door, plastic on trims and panel and all tape around oven. Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: Open the oven door as far as it will go.
PAGE 4
Installation Instructions I_ Pre-lnstallation Checklist cont. [_ Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top of the unit. lace the oven on a table or platform even with the cutout opening. (Platform must support 255 Ibs.
PAGE 5
Installation Instructions Cutout for Built-In Oven with Microwave Junction Box Location Cabinet 27" Allow 7/8" for overlap of oven over side edges Cutout Width 25" Min. 25 1/4" Max. I 2" x 4" or equivalent runners level with bottom of cutout Cabinet Width Recommended Minimum Cutout Location from Floor 21 5/8" Cutout Depth 23 112" Cutout Width 25" Min. I Cutout Height Min. 41 1/4" Max. 25 1/4" Max.
PAGE 6
Installation Instructions Electrical Connections ATTENTION Turn off the circuit breaker or remove fuses to the oven branch circuit. INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below.
PAGE 7
Installation Instructions IBI Electrical Connections New Construction and Four-Conductor Branch Circuit Connection • When installing in new construction, • When installing in a mobile home, or • When installing in a recreational Three-Conductor Branch Circuit Connection When connecting to a three-conductor circuit, if local codes permit: or vehicle, cont branch a.
PAGE 8
Installation Instructions Securing the Oven in the Opening Sliding the Oven Into the Opening Drilling the Pilot Holes and Mounting the Oven a. Loop (do not tie) a 36" string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered. Drill through the mounting holes (top and bottom) of the side trim, for the #8 screws provided.
PAGE 9
Installation Instructions Preparing for the Bottom Trim Installation I_] a. Place the bottom metal trim centered over the pre-drilled mounting holes. Tape the edges of the trim down to maintain the alignment. a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. = b. Using the trim as a template, mark the center of each slot (three total) where the mounting holes will be drilled.
PAGE 10
Installation Instructions 151Replacing the Oven Door NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. = _'-_ Open the oven door as far as it will open. _"_ Push the hinge locks up against the front frame of the oven cavity, to the locked position. / Hinge in Locked Position Lift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle.
PAGE 11
Installation Instructions Pre-Test Checklist [_ emove all protective and any stickers. [_ Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see page 9). film, if present, [_ Check to be sure the mounting screws are installed and flush with the side trim (see page 8). Operation Checklist Remove all items from the inside of the oven.
PAGE 12
NOTES 12