Installation Instructions 27” Built In Wall Oven JKP15, JKP18, JKP27BA, JKP27, JKP45, JKP56 JKS05, JK910AA, JK910, JK950 “If you have questions, call 800-GE-CARES or visit our website at: www.GEAppliances.com” Before you begin • Note to Installer- Be sure to leave these instructions with the consumer. • OWNER- Keep these instructions for future reference. • NOTE- This appliance must be properly grounded.
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical Requirements For Your Safety This appliance must be supplied with the proper voltage and frequency, and connected to an individual properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating Plate is located on oven frame.) We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician.
Installation Instructions Pre- Installation Checklist Open the door to the stop position. ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES ARE TO BE USED FOR SINGLE AND DOUBLE OVEN INSTALLATION! Remove packaging materials. Check behind hinges, and under false bottom. Remove labels on door, plastic on trims and panel, and all tape around oven. DO NOT LIFT THE DOOR BY THE HANDLE! Grasp the door on both sides and lift up and off the hinges.
Installation Instructions Pre- Installation Checklist cont. Place the oven on a table or platform even with the cutout opening. (Platform must support 150 lbs. single, 275 lbs. double.) Cover hinge with paper towel rolls or toweling. Remove the bottom trim from the top of the oven. It will be installed at the end of installation. The trim is wrapped separately and taped to the top of the unit.
Installation Instructions A1 Cutouts for Single Built-In-Oven Cabinet Width 27" 10" Junction Box Location Cutout Width 25" MIN. 25 1/4" MAX. Allow 7/8" for overlap of oven over side edges of cutout 32 1/2” Cutout Depth 23 1/2” Cutout Width 25” Min. 25 1/4” Max. 5" Cutout Height 27 5/8” Min. 28 1/8” Max. 20" Alternate junction box location Recommended cutout location from floor 32 1/2" Allow a minimum of 20" for clearance to adjacent corners, drawers, walls, etc.
Installation Instructions A2 Cutouts for Double Built-In-Oven Junction Box Location Cabinet Width 27" 10" Cutout Width 25" MIN. 25 1/4" MAX. Allow 7/8" for overlap of oven over side edges of cutout 2" x 4" or equivalent runners 56" To bottom of junction box Alternate junction box location Cutout Height 49 11/16" MIN. 50 1/8" MAX. 5" 20" Allow a minimum of 20" for clearance to adjacent corners, drawers, walls, etc.
Installation Instructions A3 Cutouts for Single Oven Under Counter Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. Gas or electric connections for gas cooktop must be located in an adjacent accessible location to the right 240V / 208V Junction Box Location 25" 5" 25" MIN. 25 1/4" MAX. 27 5/8" MIN. 28 1/8" MAX. Allow 1" unit overlap all edges 22" MIN.
Installation Instructions B B1 B2 Electrical Connections Turn off the circuit breaker or remove fuses to the oven branch circuit. NEW CONSTRUCTION AND FOURCONDUCTOR BRANCH CIRCUIT CONNECTION With the oven in front of the cabinet opening, on a table or platform, connect the flexible conduit to the electrical junction box as shown below. You will need to purchase a strain relief clamp to complete the connection of the conduit to the junction box.
Installation Instructions B Electrial Connections cont. OR Do not shorten the flexible conduit.The conduit strain Relief Clamp must be securely attached to the junction box and the flexible conduit must be securely attached to the clamp. If the flexible conduit will not fit within the clamp, do not install the oven until a clamp of the proper size is obtained. Three-Conductor Branch B4 Circuit Connection When connecting to a 3-conductor branch circuit, if local codes permit: a.
Installation Instructions C Placing the Oven in the Opening C1 Sliding the Oven Into the C3 Drilling the Pilot Holes Opening. a. Loop a 36” string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. Note: Before drilling the pilot holes make sure the oven is pushed as far back into the opening as it will go and centered. a.
Installation Instructions D Replacing the Oven Door D1 Make sure the hinge is in the door stop position. D2 Remove the toweling or paper towel holder from the hinge. D3 Grasp the door on both sides. D4 Hold the door over the hinges lining up the hinges with the hinge slots on the bottom of the door. D5 Slide the door down onto the hinges as far as it will go. D6 Close the door. The oven door is heavy. You may need help lifting the door high enough to slide it down onto the hinges.
Installation Instructions E PRE-TEST CHECK LIST Remove all protective film if present, and any stickers. Check that the bottom trim is installed properly (see page 7). Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check to be sure the mounting screws are installed and flush with the side trim, (see page 7). Operation Checklist NOTE TO ELECTRICIAN: The power leads supplied with this appliance are UL recognized for connections to larger gauge household wiring.