Spec Sheet

DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
JM250DT
GE 27" Drop-In Electric Range
For answers to your Monogram, GE Café
™
, GE Profile
™
or
GE Appliances product questions, visit our website at
geappliances.com or call GE Answer Center
®
Service, 800.626.2000.
Specification Revised 4/22
ADA
COMPLIANT
Listed by
Underwriters
Laboratories
All GE ranges are equipped with
an Anti-Tip device. The installation
of this device is an important,
required step in the installation
of the range.
Inside back wall of cabinet
or rear wall
Countertop cutout
top view
Important: This range is designed to hang from the
countertop. It does not rest on the oor.
Countertop
If necessary, build up
sides to 1-1/2" thick to
provide screw
anchor surface and
countertop support
These screws are
anti-tip devices
and must be installed
in the front and rear
Locate junction box
anywhere in shaded area
Conduit is 48-1/2" long
Door
clearance
26-1/4" MAX.
Smooth cut
22-7/8"
Cutout
23-3/8" MIN.*
Flat
counter
3/8" MIN. Flat
1-1/2" MIN.
Clearance
*If countertop edge is formed, this
dimension must extend to at area
In replacement installation, use
JX27R optional backguard, if required
30" MIN. to
bottom of
cabinet
over
range
18
Range side
support
Back of range
to front of
closed door
Trim section for
countertop with
post formed
or raised
front edge
21-3/4" cabinet
face to rear
of cutout
27" Drop-In Ranges
Dimensions (in inches)
3
27-1/8
27-3/16
24-3/16
28-7/16
28-1/2"
MIN.
27" Between
cabinets
20
24-3/16
13/32
Inside back wall of cabinet
or rear wall
Countertop cutout
top view
Important: This range is designed to hang from the
countertop. It does not rest on the oor.
Countertop
If necessary, build up
sides to 1-1/2" thick to
provide screw
anchor surface and
countertop support
These screws are
anti-tip devices
and must be installed
in the front and rear
Locate junction box
anywhere in shaded area
Conduit is 48-1/2" long
Door
clearance
26-1/4" MAX.
Smooth cut
22-7/8"
Cutout
23-3/8" MIN.*
Flat
counter
3/8" MIN. Flat
1-1/2" MIN.
Clearance
*If countertop edge is formed, this
dimension must extend to at area
In replacement installation, use
JX27R optional backguard, if required
30" MIN. to
bottom of
cabinet
over
range
18
Range side
support
Back of range
to front of
closed door
Trim section for
countertop with
post formed
or raised
front edge
21-3/4" cabinet
face to rear
of cutout
27" Drop-In Ranges
Dimensions (in inches)
3
27-1/8
27-3/16
24-3/16
28-7/16
28-1/2"
MIN.
27" Between
cabinets
20
24-3/16
13/32
NOTE: This appliance has been approved for 0" spacing to
adjacent surfaces above the cooktop. However, a 6" minimum
spacing to surfaces less than 15" above the cooktop and adjacent
cabinet is recommended to reduce exposure to steam, grease
splatter and heat.
OPTIONAL BACKGUARD
(Available at additional cost)
JX27RBK (Black)
JX27RWH (White)
INSTALLATION INFORMATION: Before installing, consult
installation instructions for current dimensional data and
additional requirements.
KW RATING
240V 10.6
208V 8.0
BREAKER SIZE
240V 40 Amp
†
208V 40 Amp
†
†
NOTE: Check local codes
for required breaker size