Built-In Wall Oven 27" (68.6 cm) models JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958 Ilnstallat!on nstruct=ons 30" (76.2 cm) models JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 If you have questions, call 1.800.GE.CARES ge.com Before You Begin Read these instructions carefully and completely. • IMPORTANT-save instructions these for local inspector's • IMPORTANT-observe use. all governing codes and ordinances.
Installation instructions PORTANT SAFETY I ST CTIONS lectrical For Your Safety • Be sure your oven is installed properly by a qualified installer or service technician. Requirements • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door. Rating plate is located on oven side trim, side front frame or lower front frame.
Insta ion instructions Pre-lnstallation Chec Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES IS TO BF USED FOR SINGLE AND DOUBLE OVEN INSTALLATION! [_ Remove packaging materials. Check behind hinges and under false bottom. Remove labels on the outside of the door, plastic on trims and panel, all tape around the oven, and any shipping screws securing the oven to the base pad.
Installation instructions uilt-ln Cutout for 27" (68.6c )Single Ovens on y For JKS10, JKP30, JKP70, PK916, ZEK938 models only. Cabinet 5" (12.7 cm) Max. from the left or right Cabinet_ _sk I 27" (68.6 cm) Cutout for overlap of oven over side edges of cutout Width tOcm) 0¥ runners Box ,, : ,, "!-' level adjacent 1" (2.5 cm) ciearance°f 20" (50.8teCta),41 for _ a_jacen, corners, drawers, wails, etc.
Installation instructions Cutoutfor 27"(68.6 Ovensonly For JKP35, JKP55, JKP75, PK956, ZEK958 models only. 5" (12.7 cm) Max. from the left or Cabinet right (68.6 cm) _ Cutout i __ Junction Box oven over 27" (68.6 cm) Recommended Cutout Location from Floor 13 1/4" (33.7 cm) Cutout Depth 23 5/8" (60 cm) Min. Cutout Width 25" (63.5 cm) Min. Location 5" (63.5 cm) Min. 25 1/4" i Allow 1" (2.5 cm) for overlap of Cabinet Width (s4.1cm) M_, side 25 114" (64.1 cm) Max.
Installation instructions Cutout for 27" (68.6c_)Single Built-in Ovens only Under Counter For JKS10, JKP30, JKPT0, PK916, ZEK938 models only. Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. \ 240V / 208V Junction Box Location 25" (63.5 cm) 5" (12.7 cm) Max.
Cabinetry for 27" (68.6 c_)Single or uilt-ln Ovens only- Over a Drawer For JKS10, JKP30, JKP35, JKP55, JKPT0, JKP75, PK916, PK956, ZEK938, ZEK958 models only. Double 27" (68.6 cm) Single 27" (68.6 cm) Oven Over Oven Over a Warming Drawer a Warming Drawer Anti-Tip Block Against Rear • Wall Per Warming Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement Drawer Requirement 2" (5.1 cm) Min. 2" (5.
Cabinetry Cutoutfor 27"(68.6 o_)SingleOvensonlyBelowan Advantiumor ;rowave Oven or Betweenan Advantiumor crowave Ovenand a WarmingDrawer For JKS10, JKP30, JKP70, PK91& ZEK938 models only. Single 27" (68.6 cm) Oven Between an Advantium or Microwave Oven and a Warming Drawer Single 27" (68.6 cm) Oven Below an Advantium or Microwave Oven Per Advantium or Microwave Oven Requirement Per Advautium or Microwave Oven Requirement 2" (5.1 cm) Min.
Installation instructions Cutout for 30"(76.2c )Sing Ovensonly Built-in For JTP30, JTP70, PT916, PT920, ZET938 models only. Cutout Width 28 1/2" (72.4 cm) 9 1/2" (24.1 cm) Junction Box Location (junction box may be located in 5/8"(72.7 ore) Max. I Allow 11/16" I (1.75 cm) for overlap of oven over side edges of cutout 21 Opening Between inside Walls Must Be At Least 28 1/2" (72.4 cm) Wide / (69.2 cm) Min, 27 5/16" (69.4 cm) Ma 30" (76.2 cm) Recommended Cutout Location from Floor 32 1/2" (82.
Installation instructions Cutoutfor 30"(76.2 cm) Ovensonly For JTP35, JTP55, JTP75, PT956, PT960, ZET958 models Cutout Width 28 1/2" (72.4 cm) Min. -,_ 28 5/8" (72.7 cm) Max. 9 1/2" (24.1 cm) Junction Box n (junction box may be located Location in adjacent cabinet) _t /" Allow 11116" (1.75 cm) for overlap of oven over side edges of cutout Allow a minimum of 21" (53.3 cm) for clearance to adjacent \ 21" (53.3 cm)_ Cutout Depth 23 1/2" (59.7 cm) Min. Cutout Width 28 1/2" (72.4 cm) Min.
Installation instructions Cutout for 30"(76.2 Single only Under Coun :r lit-in Ovens For JTP30, JTPT0, PT916, PT920, ZET938 models only. Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. 240V / 208V Junction Box \ 25" (63.5 Location (junction box may be in adjacent cabinet) 9 1/2" (24.1 cm) cm) Top and/or side fillers may be necessary if unit is positioned between existing cabinets.
Cabinetry Cutout for 30"(76.2c_) Single or Double L_i -in Ovens only- Over a _rrning Drawer For JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 models only. Single 30" (76.2 cm) Oven Over a Warming Drawer Double 30" (76.2 cm) Oven Over a Warming Drawer Block Against Rear Wall Per Warming Drawer Requirement Anti-Tip Block Against Rear Wall Per Warming 2" (5J cm) IVlin. Drawer Requirement NOTE: Install the 2" (5.
Cabinetry Cutoutfor 30"<76.2 o_)SingleOvensonlyBelowan Advantium or _-rowaveOven or Betweenan Advantiumor crowave Ovenand a WarmingDrawer For JTP30, JTP70, PT916, PT920, ZET938 Single 30" (76.2 cm) Oven Below an Advantium or Microwave Oven models only. Single 30" (76.2 cm) Oven Between an Advantium or Microwave Oven and a Warming Drawer Per Advantium Microwave Oven Requirement __" 2" (5.1 cm) Min. (5.
Installation instructions Electrical Connections ATTENTION Turn off the circuit breaker or remove fuses to the oven branch circuit. iNSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below.
Installation instructions New Construction and Four=Conductor Branch Circuit Connection • When installing in new construction, Three=Conductor Branch Circuit Connection When connecting to a three-conductor circuit, if local codes permit: or a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
Installation instructions Securing the Oven Sliding the Oven into the Opening m In e Openin Drilling the Pilot Holes and Mounting the Oven a. Loop (do not tie) a 36" (91 cm) string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered. a.
Installation instructions [_ Preparing for the Bottom Trim Installation a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. b. Using the trim as a template, mark the center of each slot (two total) where the mounting holes will be drilled. c. Remove the trim. d. Drill pilot holes into the center of each template mark. a= For 27" (68.
Installation instructions Replacing the Oven Door NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. [=_ Open the oven door as far as it will open. [=_ Push the hinge locks up against the front frame of the oven cavity, to the locked position, Hinge in Locked Position Lift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle.
Installation instructions Pre-Test C ec Remove all protective and any stickers. ist Check that the bottom trim is installed properly (see page 17). film, if present, Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check to be sure the mounting screws are installed and flush with the side trim (see page 16). Operation Checklist Remove all items from the inside of the oven.
Notes 20
Instrucciones de instalacibn I &Preguntas? Modelos de 27" (68,6 cm) JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958 Modelos de 30" (76,2 cm) JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 I Visite nuestro sitio en la Web: ge.com Antes de empezar Lea estas instrucciones cuidadosa y completamente. • IMPORTANTE-Guarde estas instrucciones y tengalas para el inspector local.
Instrucciones INSTRUCCIONES IMPORTANTES de instalacibn DE SEGURIDAD Para su seguridad Requisitos el ctricos * Cerciorese de que su horno sea instalado adecuadamente por un instalador calificado o por un tecnico de servicio. cont. o Cerci6rese de que su homo este firmemente instalado en un gabinete que este firmemente adherido a la estructura de la casa. El peso sobre la puerta del horno podria causar que el horno se voltee resultando en lesiones.
Instrucciones de instalacibn p Lista de control antes de la instalacibn No es necesario retirar la puerta para la instalaci6n del producto, pero hacerlo facilita la instalaci6n. Para retirar la puerta: iTODA LA INFORMACION PARA LA INSTALACION EN LAS PAGINAS SIGUIENTES ES PARA SER USADA EN LA INSTALACION DE HORNOS DE UNA O DOS UNIDADES! Abra la puerta del horno hasta el m_.ximo. Ernpuje los topes de las bisagras hacia abajo, hacia el marco de la puerta hasta la posici6n abierta.
Instrucciones de instalacibn l-A-] Corte para los hornos de una unidad de 27" (68,6 cm)solamente Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente. 5" (12,7 cm) M_x. espacio para el lado izquierdo oderecho Ancho del_ gabinete _ 27" (68,6 cm) i _ ¢ Ubicaci6n de la caja de conexion Ancho del corte Permita 1" (2,5 cm) de sobrepaso del horno sobre los bordes laterales del 25" (63,5 cm) Min.
Instrucciones de instalacibn I-A-1Cortepara los hornos de dos unidades de 27" (68,6 cm) solamente Para los modelos JKP35, JKP55, JKP75, PK956, ZEK958 solamente. 5" (12,7 cm) M&x. espacio para el lado izquierdo o derecho _ Ancho del _ gabinete _ 27" (68,6 cm). Ancho del gabinete J Ubicaci6n J. i--_Lr t I Permita 1" (2,5 cm) para sobrepaso del horno sobre los bordes laterales -del corte Anchodel corte 25" I -i-.
Instrucciones de instalacibn Corte para los hornos de una unidad-debajo de la superficie del gabinete de 27"(68,6 cm)solamente Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente. Las estufas el_ctricas o de gas se pueden instalar sobre este horno. Consulte las instrucciones de la estufa para el tamaho del corte. Consulte la etiqueta encima del horno para los modelos de estufas aprobados. Ubicaci6n de la caja de conexi6n 240V / 208V 25" (63,5 cm) 5" (12,7 cm) M_x.
Gabinetes Disyuntor para 27"(68,6 cm) solamente para hornos individuales o dobles empotrados- Sobre una gaveta de calentamiento Para los modelos JKS10, JKP30, JKP35, JKP55, JKP70, JKP75, PK916, PK956, ZEK938, ZEK958 solamente.
Gabinetes I_1Disyuntor para27"(68,6cm)Solamente parahornos individuales - Debajo deunAdvantium odeun horno demicroondas oEntreunhorno Advantium o unhornodemicroondas yGaveta decalentamiento Para los modelos JKS10, JKP30, JKP70, PK916, ZEK938 solamente. Hornoindividualde27"(68,6cm) debajode unhornoAdvantiumo un hornode microondas Por Advantium de microondas o horno requisitos 2" (5,1 cm) Min.
Instrucciones de instalacibn Corte para los hornos de una unidad de 30" (76,2 cm) solamente Para los modelos JTP30, JTP70, PT916, PT920, ZET938 solamente. Ancho del corte 28 1/2" (72,4 cm) Min. 28 518" (72,7 cm) "=== M_x. Ubicacion de la caja de conexi6n 9 1/2" (24,1 cm) -_ _ -- . -- Mbx_ (la caja de conexi6n / puede estar ubicada en un gabinete adyacente) _ I I / entre los paredes interiores debeestar I I I I (72,4 cm) de ancho --__+ del corte i 27 1/4" _, (69,2 cm) Min.
Instrucciones de instalacibn Corte para los hornos de dos unidades de 30" (76,2 cm)solamente Para los modelos JTP35, JTP55, JTP75, PT956, PT960, ZET958 solamente. Ancho del corte 28 1/2" (72,4 cm) Min. _r28 5/8" (72,7 cm) M&x. 9 112" (24,1 cm) M&x.
Instrucciones de instalacibn Corte para los hornos de una unidad -debajo de la superficie del gabinete de 30" (76,2 cm)solamente Para los modelos JTP30, JTP70, PT916, PT920, ZET938 solamente. Las estufas el_ctricas o de gas se pueden instalar sobre este horno. Consulte las instrucciones de la estufa para el tamaho del corte. Consulte la etiqueta encima del horno para los modelos de estufas aprobados.
Gabinetes Disyuntor para 30"(76,2 cm)solamente para hornos individuales o dobles empotradosSobre una gaveta de calentamiento Para los modelos JTP30, JTP35, JTP55, JTP70, JTP75, PT916, PT920, PT956, PT960, ZET938, ZET958 solamente. Horno individual de 30" Horno doble de 30" (76,2 cm) sobre una (76,2 cm) sobre una gaveta de calentamiento gaveta de calentamiento Bloque estable contra la pared trasera para la gaveta de calentamiento requisitos 2" (5,1 cm) Min.
Gabinetes Disyuntor para30"(76,2cm)Solamente parahornos individuales - Debajo deunAdvantium o deun hornodemicroondas o EntreunhornoAdvantium o unhornodemicroondas y Gavetadecalentamiento Para los modelos JTP30, JTP70, PT916, PT920, ZET938 solamente. Hornoindividualde30"(76,2cm) debajode unhornoAdvantiumo un hornode microondas Hornoindividualde 30"(76,2cm) EntreunhornoAdvantiumo unhornode microondasy unagavetadecalentamiento Por Advantium Por Advantium o horno de microondas requisitos 2" (5,1 cm) Min.
Instrucciones de instalacibn IBIConexiones el ctricas ATENCION AL INSTALADOR: Desconecte el interruptor del circuito o retire los fusibles que alimentan el circuito ramal del horno. Todos los hornos electricos de pared deben ser cableados directamente en una caja de conexibn. Una "enchufe-recept_iculo" NO ES permitido en estos productos. Con el horno enfrente de la abertura del gabinete, sobre una mesa o plataforma conecte el conducto flexible a la caja de conexi6n como se muestra en la figura.
Instrucciones de instalacibn [B3-] Conexibn para nueva construccibn y de circuito ramal de cuatro conductores i--- -i Conexibn de circuito ramal de tres conductores Cuando conecte un circuito ramal de 3 conductores, si los codigos locales Io permiten: • Cuando se instale en una construccion nueva, o • Cuando se instale en una casa movil, o a. Conecte el alambre descubierto del horno con el alambre neutro (blanco) del circuito ramal (blanco o gris), usando una tuerca para alambres.
Instrucciones de instalacibn Posicibn firme del horno en la abertura Cbmo deslizar el horno en '---' el interior de la abertura '--' a. Coloque (sin atar) una cuerda de 36" (91 cm) alrededor del conductor antes de deslizar el horno en su lugar. Esto evitara que el conducto se caiga detras del horno. Cbmo taladrar los orificios piloto y montar el horno NOTA: Antes de perforar los orificios piloto, cercibrese de que el horno se empujo hasta el fondo y de que est_ centrado.
Instrucciones de instalacibn Preparacion para la instalacion de la moldura de fondo I_] a. Con el horno instalado, tome la moldura de fondo y centrela en el borde frontal del fondo de la abertura del gabinete. b. Usando la moldura como una plantilla, marque el centro de cada ranura (dos en total) donde los orificios de montaje seran taladrados. a.
Instrucciones de instalacibn 151Cbmo instalar la puerta del horno NOTA: La puerta del horno es pesada. Quiz_s necesite ayuda para levantar y deslizar la puerta hacia abajo sobre las bisagras. No levante la puerta por la empu_adura. _'-_ Abra la puerta del horno hasta el maximo. _] Empuje los topes de las bisagras contra el marco frontal de la cavidad del horno, hasta alcanzar la posici6n de cierre. Bisagra en la posicion de cierre Levante la puerta del horno colocando una mano en cada lado.
Instrucciones de instalacibn Lista de control antes de la prueba [_ [_ etire cualquier cinta este de proteccion etiqueta que todavia presente. Inspeccione la moldura de fondo para cerciorarse de que esta instalada apropiadamente (ver pagina 17). y los alambres esten bien conectados y Revise para asegurarse de que todos no aplastados o en contacto con partes moviles.
Notas 20