Manual

ManualsBrandsGE ManualsRange hoodOfficial GE range hood

36" VentedHood

_ Safety Instructions...Front Cover, 2

_ Operating Instructions .........2,3

Automatic Heat Sensor ...........................3

Controls .....................................................2

Cleaning ....................................................3

Filter............................................................3

Light Bulb Replacement ..........................3

Installation .....................................4-6

Damper/Duct Connector .........................5

Electrical Wiring .......................................6

Filter Panel .............................................3, 5

Mounting Brackets ...................................5

Consumer Services .....................7

Important Phone Numbers .....................7

Warranty ..................................Back Cover

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

SAFETYPRECAUTIONS

WARNING- To REDUCETHERISKOFFIRE,

ELECTRICSHOCKORINJURY TOPERSONS,

OBSERVETHEFOLLOWING:

A. Use this unit only in tile manner intended

by the manufacturer, lfyou have questions.

contact the manufactm'e_

B. Before smwidng or cleaning umt. switch

WARNING- To REDUCETHERISKOFA

RANGETOPGREASEFIRE:

A. Never lem e surface units unattended at high

settings. Boilovers cause smoking and gTeasy

spillovers that may ignite. Heat oils slowly on

low or medium settings.

B. Ahva) s turn hood ON when cooking at high

power off at service panel and lock the service heat or when cooking flaming foods.

disconnecting means to prevent power fl'om

being switched on accidentally. When the

selwice disconnecting means cannot be locked.

securely fasten a prominent wm'ning device,

such as a tag, to the smMce panel.

C. Do not use this unit with an) solid-state speed

control device.

C. Clean ventilating fans fl'equenfly. Grease should

not be allowed to accmnulate on fian or filter.

D. Use proper pan size. Mways use cookware

appropriate for the size of the surface

element.

co_ztimted _zextpage

D. [ se with approved cord-connection kit only.

E. This unit must be grounded.

GEAppfiances

I Models: JV694 JV695 JV696 JV960

Summary of content (8 pages)

PAGE 1
36" Vented Hood _ Safety Instructions...Front Installation Cover, 2 ..................................... 4-6 Damper/Duct Connector .........................5 _ Operating Instructions Electrical Wiring .......................................6 Filter Panel .............................................3, 5 Mounting Brackets ...................................5 .........2,3 Automatic Heat Sensor ...........................3 Controls .....................................................
PAGE 2
IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING. SAFETY PRECAUTIONS REDUCE THE RISK OF FIRE, CAUTION- For _e,eralve,tilati, guse o,Iv. oo,or WARNING- TO use to exhaust hazardous or explosive materials and vapors. WARNING- To REDUCETHERISKOFINJURY TO PERSONSIN THEEVENTOFA RANGETOPGREASEFIRE, OBSERVETHEFOLLOWING*: A. SIVIOTHER FIAIVIES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
PAGE 3
Automatic Heat Sensor Your hood is equipped with an automatic thermostat. This thermostat is a device that will turn on or speed up the blower if it senses excessive heat above the cooking surface. If your blower is not on, or if it is running at low speed, the thermostat will sense excessive cooking heat, override the norn-lal blower control and turn the blower on to high speed. _l_e blower will run until the temperature drops to normN operating level.
PAGE 4
TOOLSYOU WILL NEED Flat blade and Phillips screwdrivers This hood can easily be installed by following these basic steps: • Mark and cut out the cabinet bottom. Pencil • Secure the hood to the cabinet. • Mount the cabinet on the wall. • Connect the ductwork and the power cable. Duct tape Saw (saber or keyhole) Electric Drill Metal Snips (in some applications) / 18" MIN, ¢ Pliers Tape measure Wire stripper Flashlight Caulking FLUSH BOTTOM CABINET Level qPLANTHEINSTALLATION _= 18" MIN.
PAGE 5
2. Attach the damper/duct connector. 7. Install the mounting brackets. ELECTRICAL KNOCKOUTS #8-18 x 3/8" FRONT OFHOOD Hold the left hand mounting bracket the side of the housing as shown. Use two (2) screws (provided) to attach the connector to the housing. The damper flap should open in the direction indicated by the arrow. 3. Remove the electrical on #8-18 x 2" OR knockout. Choose either the top or side of the housing for the electrical cable entrance. Remove the appropriate knockout. 4.
PAGE 6
8. Secure the hood to the cabinet. 13. Install P.,sT,oc,P the glass visor assembly. [ CONTROL TRIM VISOR TRIM Align the hood with the sides and front edge of the cabinet. Tighten the screws in each mounting bracket. Place plastic caps (provided) over the ends of these screws from the inside of the cabinet. THUMB SCREWS Install two (2) additional screws into the cabinet bottom, through the front mounting holes along the front edge of the hood. 9. Replace the access cover.
PAGE 7
We'll Be There With the purchase of your new GE appliance, receive the assurance that if you ever need infbrmation or assistance fiom GE, we'll be there. All you have to do is call--toll-fiee! GEAnswer Center 800.626.2000 Whatever your question intormation service be answered i_romptly (_enter =r ® selwice about is available and is open any GE major appliance, to hell). Your call--and And you courteously.
PAGE 8
YOUR 36" HOOD WARRANTY WHAT IS COVERED Staple sales slip or cancelled check here. Proof of original purchase date is needed to obtain service under warranty.