Installation Instructions

ManualsBrandsGE ManualsWall-Mounted Range HoodsJVW5301SJSS

Installation

Instructions

“If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: GEAppliances.com”

INSTALLATION INSTRUCTIONS

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

•

IMPORTANT ³Save these instructions

for local inspector’s use.

•

IMPORTANT ³ Observe all governing

codes and ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• Skill level – Installation of this vent hood

requires basic mechanical and electrical skills.

• Completion time – Approximately

1 to 3 hours

• Proper installation is the responsibility of the

installer.

• Product failure due to improper installation is

not covered under the Warranty.

FOR YOUR SAFETY:

WARNING: Before beginning the

installation, switch power off at service panel and

lock the service disconnecting means to prevent

power from being switched on accidentally.

When the service disconnecting means cannot

be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

CAUTION: Due to the weight and size of

these vent hoods and to reduce the risk of

personal injury or damage to the product, TWO

PEOPLE ARE REQUIRED FOR PROPER

INSTALLATION.

Pyramid Wall

Chimney Vent Hoods

JVW5301, JVW5361

WARNING: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring

must be done by qualified person(s) in

accordance with all applicable codes and

standards, including fire-rated construction.

B. Sufficient air is needed for proper

combustion and exhausting of gases

through the flue (chimney) of fuel burning

equipment to prevent back drafting. Follow

the heating equipment manufacturer’s

guidelines and safety standards such

as those published by the National Fire

Protection Association (NFPA), the

American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE)

and the local code authorities.

C. When cutting or drilling into wall or ceiling,

do not damage electrical wiring and other

hidden utilities.

D. Ducted fans must always be vented to the

outdoors.

E. Turn off breaker to adjacent rooms while

working.

WARNING: TO REDUCE THE RISK

OF FIRE, USE ONLY METAL DUCT WORK.

(991.0364.803 rev 2) 31-10983-1 04-15 GE

Summary of content (16 pages)

PAGE 1
Pyramid Wall Chimney Vent Hoods JVW5301, JVW5361 “If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: GEAppliances.com” BEFORE YOU BEGIN Read these instructions completely and carefully. • IMPORTANT ³ Save these instructions for local inspector’s use. • • • • • • • IMPORTANT ³ Observe all governing codes and ordinances. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions for future reference.
PAGE 2
INSTALLATION PREPARATION Installation Preparation PRODUCT DIMENSIONS INSTALLATION CLEARANCES These vent hoods are designed to be installed onto a wall with no above cabinets. • Install these hoods between the required 24” minimum and 36” recommended maximum above the cooking surface. 8-1/4” 7-1/16” 17-3/8” Min. 24-7/16" Max. 13” 10-1/8” 24” Required Min. 36” Recommended Max.
PAGE 3
ADVANCE PLANNING Duct Install Planning • This hood is designed to be vented vertically through the ceiling. Use a 6" round duct. Use locally supplied elbows to vent horizontally through the rear wall. • Use metal ductwork only. • Determine the exact location of the vent hood. • Plan the route for venting exhaust to the outdoors. To maximize the ventilation performance of the vent system: 1. Minimize the duct run length and number of transitions and elbows. 2. Maintain a constant duct size. 3.
PAGE 4
INSTALLATION PREPARATION Installation Preparation TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED) CAUTION: Safety glasses Pencil and tape measure Spirit level Wire cutter/stripper • 1 Hardware Package • 1 Literature Package PARTS NEEDED FOR INSTALLATION Electric drill, #2 Phillips, flat head, and 9/32" drill bit Strain relief for junction box REMOVE THE PACKAGING CAUTION: Wear gloves to protect against sharp edges. • Remove the duct covers.
PAGE 5
RANGE HOOD COMPONENTS A. Canopy Section B. Lower Duct Cover C. Upper Duct Cover D. Mounting Screws E. Duct Cover Mounting Brackets F. Duct Cover Screws G. Damper H. Canopy Mounting Anchors I. Duct Cover Anchors The Pyramid Chimneys are adjustable and designed to meet varying ceiling heights. The duct covers can be adjusted for ceilings between 7’ 3 1/4” and 8’ 10 5/16” depending on the distance between the bottom of the hood and the cooktop (distance X).
PAGE 6
INSTALLATION PREPARATION Installation Preparation PREPARE THE WALL Duct Covers Hood Body and Power Supply 1. Place one of the duct cover brackets against the wall so that its top edge is 1/16” from the ceiling and level. Align the center notches of the bracket and the centerline (C) and mark the centers of the bracket holes. Remove the bracket to drill the 2 holes for installation with a 9/32" drill bit, and insert the duct cover anchors.
PAGE 7
PREPARE HOOD FOR INSTALLATION 1. Remove the grease filters from the unit and set aside. The grease filters are removed by pressing the handle in front of the filter. When replacing, make sure that the filters are properly positioned with the handles in front and visible. 2. Remove and properly discard the protective plastic wrapping from the hood and grease filters. 3. Remove junction box cover. Non-vented (recirculation) Installations (Continued) 2.
PAGE 8
INSTALLATION INSTRUCTIONS Installation Instructions ELECTRICAL CONNECTION FINISH THE INSTALLATION 1. Connect the Power Supply Cable to the range hood. Attach the white lead of the power supply to the white lead of the range hood (A) with a wire nut (C). Attach the black lead of the power supply to the black lead of the range hood (B) with a wire nut (C). Connect the green (D) ground wire under the green grounding screw. 2. Replace the junction box cover. (Continued) 3.
PAGE 9
Campanas de Ventilación de Chimeneas de Pared Pirámide JVW5301, JVW5361 ¿Preguntas? Llame al 800.GE.CARES (800.432.2737) o visite nuestro sitio Web en: GEAppliances.com ANTES DE COMENZAR Lea estas instrucciones por completo y con detenimiento. • IMPORTANTE ³ Guarde estas instrucciones para el uso de inspectores locales. • • • • • • • IMPORTANTE ³ Cumpla con todos los códigos y ordenanzas vigentes. Nota al instalador – Asegúrese de dejar estas instrucciones con el Consumidor.
PAGE 10
PREPARACIÓN PARA LA INSTALACIÓN Preparación para la instalación DIMENSIONES DEL PRODUCTO ESPACIO DE INSTALACIÓN 8-1/4” 7-1/16” 17-3/8” Min. 24-7/16" Max. 13” 10-1/8” 18-1/2” 30” to 36” 13” 5” 3-5/16” 2” 1-3/8” 4-1/4” 2 Estas campanas de ventilación están diseñadas para ser instaladas en una pared sin gabinetes superiores. • Instale estas campanas entre el mínimo requerido de 24” y el máximo recomendado de 36” sobre la superficie de cocción. 24” Required Min. 36” Recommended Max.
PAGE 11
PLANIFICACIÓN PREVIA SUMINISTRO DE ENERGÍA Planificación para la Instalación con Conducto • Esta campana está diseñada para ventilarse en forma vertical a través del cielorraso. Use un conducto circular de 6”. Utilice codos suministrados en forma local para ventilación horizontal a través de la pared trasera. • Determine la ubicación exacta de la campana de ventilación. • Planifique el recorrido de la salida de ventilación hacia el exterior.
PAGE 12
PREPARACIÓN PARA LA INSTALACIÓN Preparación para la instalación HERRAMIENTAS Y MATERIALES REQUERIDOS (NO SUMINISTRADOS) Gafas de seguridad Lápiz y cinta métrica Nivel Alicate pelacables Broca eléctrica con Phillips Nº 2 de cabeza plana y broca de 9/32” Cinta aislante de aluminio Tapones de alambre aprobados por UL Alivio de tensión para la caja de conexiones QUITE EL ENVOLTORIO PRECAUCIÓN: Se guantes para protegerse de los bordes afilados. • Quite las cubiertas de los conductos.
PAGE 13
COMPONENTES DE LA CAMPANA EXTRACTORA A. Sección de la Base B. Cubierta del Conducto Inferior C. Cubierta del Conducto Superior D. Tornillos de Montaje E. Soportes de Montaje de la Cubierta del Conducto F. Tornillos de la Cubierta del Conducto G. Regulador H. Soportes de Montaje de la Base de la Campana I. Soportes de la Cubierta del Conducto DIMENSIONES DE INSTALACIÓN Las Chimeneas de Pirámide son ajustables y están diseñadas para adaptarse a diferentes alturas de cielorraso.
PAGE 14
PREPARACIÓN PARA LA INSTALACIÓN Preparación para la instalación PREPARE LA PARED Cubiertas de Conductos Cuerpo de la Campana y Suministro de Corriente 1. Coloque uno de los soportes de la cubierta del conducto contra la pared, de modo que su extremo superior esté a 1/16” del cielorraso y que quede nivelado. Alinee las ranuras centrales del soporte con la línea central (C) y marque los centros de los agujeros del soporte.
PAGE 15
PREPARE LA CAMPANA PARA SU INSTALACIÓN 1. Retire los filtros de grasa de la unidad y deje los mismos a un lado. Los filtros de grasa son retirados presionando la manija que se encuentra frente al filtro. Al realizar el reemplazo, asegúrese de que los filtros estén correctamente posicionados con las manijas en el frente y visibles. Instalaciones sin ventilación (recirculación) (continúa) 2.
PAGE 16
INSTRUCCIONES DE INSTALACIÓN Instrucciones de instalación CONEXIÓN ELÉCTRICA FINALICE LA INSTALACIÓN (continúa) 1. Conecte el Cable de Suministro de Corriente a la campana extractora. Conecte el conductor blanco del suministro de corriente al conductor blanco de la campana extractora (A) con una tuerca para cable (C). Conecte el conductor negro del suministro de corriente al conductor negro de la campana extractora (B) con una tuerca para cable (C).