Installation Guide

ManualsBrandsGE ManualsAppliance partsProfile Microwave Trim Kit

PART QUANTITY

Trim Frame 1

Bottom Duct 1

Top Bracket 1

Phillips Round-Head 24

Screws (22 required

for installation)

Phillips Flat-Head 5

Screws (4 required for

installation)

Anti-Tip Bracket 1

Bottom Bracket 1

Template 1

PARTS INCLUDED

Questions? Call GE Answer Center at 800.626.2000 or

Visit our Website at:

www.GEAppliances.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS

Installation Built-In Trim Kits

Instructions

JX2127 and JX2130

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• For easier installation and personal safety, we

recommend that two people install this microwave oven.

• Unplug the microwave oven before attempting

installation of this kit.

BEFORE YOU BEGIN

• Skill level – Installation of this appliance requires basic

mechanical and electrical skills.

• Completion time – 1-3 hours

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• This kit is UL listed for installation alone or over

any General Electric/Hotpoint/RCA single electric

wall oven.

TOOLS YOU WILL NEED

#2 Phillips screwdriver

Pencil

Tape measure

Awl or punch

Drill with

⁄64″ bit or #35

FOR YOUR SAFETY:

WARNING – Before beginning the

installation, switch power off at service panel and lock

the service disconnecting means to prevent power

from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten

a prominent warning device, such as a tag, to the

service panel.

Scissors (optional)

Summary of content (4 pages)

PAGE 1
Installation Instructions Built-In Trim Kits JX2127 and JX2130 Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at: www.GEAppliances.com BEFORE YOU BEGIN Read these instructions completely and carefully. IMPORTANT – • Save these instructions for local inspector’s use. • Observe all governing codes and ordinances. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these instructions for future reference.
PAGE 2
Installation Instructions 2 INSTALL BOTTOM BRACKET AND BOTTOM DUCT 1 CUTOUT DIMENSIONS Models 27″ 30″ Height 16 ⁄ ″ 16 ⁄ ″ Width 251⁄2″ 251⁄2″ 191⁄2″ or 22″ 191⁄2″ or 22″ 34 Depth (min.)* A Fit the tab on the bottom bracket into the slot on the back of the bottom duct, and push down until the bracket is flush with the bottom of the duct. Fasten the bottom bracket to the bottom duct by using two bronze round-head screws.
PAGE 3
Installation Instructions 3 INSTALL THE ANTI-TIP BRACKET 4 INSTALL MICROWAVE OVEN INTO CABINET A Draw a line on the cutout floor at the center of the cutout, and extend the line 1⁄2″ down the face of the cabinet. A Slide the microwave oven part way into the cabinet opening. B Plug in the microwave oven. B Fold or cut the front edge of the template, along the front guide line.
PAGE 4
Installation Instructions 5 INSTALL THE TOP BRACKET 6 INSTALL THE TRIM FRAME A Place the top bracket on the top of the microwave oven, with the tabs on the top and sides of the bracket fitting squarely against the microwave oven. A Place the trim frame over the microwave oven. B Snap the two spring clips on the trim frame into the slots on the top bracket. Tabs Slots Screws Tabs Spring Clips C Open the microwave oven door.