User Manual

ManualsBrandsGE ManualsAppliance parts30 in. Optional Built-In Trim Kit in Black Stainless Steel

Part Quantity

Trim Frame 1

Screw Covers 4

Base Pan 1

Upper Bracket 1

Rail 2

Bottom

Bracket

Phillips Round-

Head Screws

(19 required

for installation)

Phillips Round-

Head Flat-

tipped Screws

(4 required for

installation)

PARTS INCLUDED

Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at:

www.GEAppliances.com

READ CAREFULLY.

KEEP THESE INSTRUCTIONS

Installation Built-In Trim Kits

Instructions

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these

instructions for local inspector’s use.

•

IMPORTANT – Observe all

governing codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions

for future reference.

• For easier installation and personal safety, we

recommend that two people install this microwave oven.

• Unplug the microwave oven before attempting

installation of this kit.

• Skill level – Installation of this appliance requires

basic mechanical and electrical skills.

• Completion time – 1-3 hours

• Proper installation is the responsibility of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• This kit and microwave are approved for installation

alone or above any single electric wall oven. Do not

mount adjacent (within 2 feet) to any range, cooktop,

gas oven, or other microwave.

TOOLS YOU WILL NEED

#2 Phillips

screwdriver

Pencil

Tape measure

Level

Small flathead

screwdriver

Drill with

»64” bit or #35

FOR YOUR SAFETY

WARNING

Before beginning the installation,

switch power off at service panel and lock the

service disconnecting means to prevent power from

being switched on accidentally. When the service

disconnecting means cannot be locked, securely

fasten a prominent warning device, such as a tag, to

the service panel.

WARNING

This oven must be plugged into a

properly grounded 3-hole, 120 volt receptacle as

required by the National Electric Code.

MODELS

30” Profile Kit: JX7230DLWW, JX7230DLBB,

JX7230ELES, JX7230SLSS, JX7230BLTS

27” Profile Kit: JX7227DLWW, JX7227DLBB,

JX7227ELES, JX7227SLSS, JX7227BLTS

Monogram Kit: ZX2130SLSS, ZX2127SLSS

Summary of content (8 pages)

PAGE 1
Installation Instructions Built-In Trim Kits Questions? Call GE Answer Center at 800.626.2000 or Visit our Website at: www.GEAppliances.com MODELS TOOLS YOU WILL NEED 30” Profile Kit: JX7230DLWW, JX7230DLBB, JX7230ELES, JX7230SLSS, JX7230BLTS 27” Profile Kit: JX7227DLWW, JX7227DLBB, JX7227ELES, JX7227SLSS, JX7227BLTS Monogram Kit: ZX2130SLSS, ZX2127SLSS #2 Phillips screwdriver Drill with 7»64” bit or #35 BEFORE YOU BEGIN Pencil Read these instructions completely and carefully.
PAGE 2
Installation Instructions CUTOUT DIMENSIONS GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
PAGE 3
Installation Instructions 3 INSTALL UPPER BRACKET 1 LOCATE AND INSTALL BASE PAN Install the Upper Bracket on the top of the cabinet. Center the Upper Bracket in the top of the cabinet cutout making sure the front flanges are against the cabinet front wall. Once centered, secure the Upper Bracket using 4 short screws. Set Base Pan into the front cabinet microwave oven cutout and center it right and left. Push back until the front flange is against the cabinet front wall.
PAGE 4
Installation Instructions 8 INSTALL THE TRIM FRAME 5 INSTALL THE MICROWAVE OVEN Plug the power cord into the wall receptacle. Slide the microwave oven assembly gently into the cabinet, using care not to pinch the power cord. Be sure to keep the assembly centered as it slides back to where the tongue of the rails goes through the slots on Base Pan. The rails should be tight against the cabinet. Using a small flat-head screwdriver, remove the 4 screw covers that are installed in the trim frame.
PAGE 5
Instrucciones de Instalación Kits Ajustables para Empotrar ¿Preguntas? Llame a un Centro de Consultas de GE comunicándose al 800.626.2000 o visite nuestro sitio web en: www.geappliances.com MODELOS Kit Profile de 30”: JX7230DLWW, JX7230DLBB, JX7230ELES, JX7230SLSS, JX7230BLTS Kit Profile de 27”: JX7227DLWW, JX7227DLBB, JX7227ELES, JX7227SLSS, JX7227BLTS Kit Monogram: ZX2130SLSS, ZX2127SLSS ANTES DE COMENZAR HERRAMIENTAS QUE NECESITARÁ Lea estas instrucciones en su totalidad y atentamente.
PAGE 6
Instrucciones de Instalación DIMENSIONES DEL RECORTE INSTRUCCIONES DE CONEXIÓN A TIERRA Modelos Este electrodoméstico deberá estar conectado a tierra. En caso de que se produzca un cortocircuito, la conexión a tierra reduce el riesgo de descarga eléctrica, brindando un cable de escape de la corriente eléctrica. Este electrodoméstico está equipado con un cable de corriente que posee un cable de conexión a tierra con un enchufe a tierra.
PAGE 7
Instrucciones de Instalación 3 INSTALACIÓN DEL SOPORTE SUPERIOR 1 UBIQUE E INSTALE UNA OLLA DE LA BASE Instale el Soporte Superior sobre la parte superior del gabinete. Centre el Soporte Superior en la parte superior del espacio libre del gabinete, asegurándose de que las lengüetas frontales se encuentren contra la pared frontal del gabinete.
PAGE 8
Instrucciones de Instalación 8 5 INSTALE EL HORNO MICROONDAS Enchufe el cable de corriente en el tomacorriente. Deslice el ensamble del horno microondas al gabinete de forma cuidadosa, teniendo cuidado de que no haya pellizcos sobre el cable de corriente. Asegúrese de mantener el ensamble centrado a medida que se vuelve a deslizar hacia las lengüetas de los rieles a través de las ranuras de la Olla de la Base. La Base debería estar ajustada contra el gabinete.