KTC-117V3/117V9 KTC-217CV3/217CV9 KTC-247CEV3/247CEV9 Cameras
© 2003 Kalatel, a GE Interlogix company All Rights Reserved. Any GE Interlogix, Kalatel division, software supplied with GE Interlogix, Kalatel division, products is proprietary and furnished under license and can be used or copied only in accordance with the terms of such license. This document contains proprietary information that is protected by copyright.
KTC-117/217/247 User Manual Table of Contents TABLE OF CONTENTS BEFORE YOU BEGIN ............................................................... 4 1 INTRODUCTION ................................................................. 5 2 CAMERA BACK PANEL ...................................................... 6 3 PROGRAMMING THE DIP SWITCH ....................................... 7 3.1 BACKLIGHT COMPENSATION (BLC OFF OR ON) ......... 7 3.2 FLICKER CONTROL (FL OFF OR ON) ......................... 7 3.
Before You Begin KTC-117/217/247 User Manual BEFORE YOU BEGIN Read these instructions before installing or operating this product. Note: This installation should be made by a qualified service person and should conform to local codes. This manual provides installation and operation information.
KTC-117/217/247 User Manual 1 Introduction INTRODUCTION The KTC-117/217/247 cameras come in an all-in-one package that includes the components shown in Figure 1. 24 VAC Camera Mounting hardware and BNC connectors Mounting bracket Power supply unit Figure 1. Package contents See Table 1 for the camera models and their descriptions. Table 1. KTC-117/217/247 camera models Model Camera type Built-in lens KTC-117V3 B/W, high res. 3 – 8 mm KTC-117V9 B/W, high res.
Camera Back Panel 2 KTC-117/217/247 User Manual CAMERA BACK PANEL See Figure 2 when performing the camera setup and adjustment procedures. Direct drive auto iris level adjuster DIP switch Terminal block Power LED Video out Figure 2.
KTC-117/217/247 User Manual 3 Programming the DIP Switch PROGRAMMING THE DIP SWITCH To program the DIP switch (Figure 2), refer to Figure 3 or Figure 4 depending on your camera model. Backlight compensation off/on Flickerless off/on Normal view / mirror view (flips picture left to right) Normal / E Zoom Figure 3.
Programming the DIP Switch 3.3 KTC-117/217/247 User Manual WHITE BALANCE (ATW OR FIX) Note: This switch is not available for the KTC-117 cameras • Auto-tracking white balance (ATW) mode In the ATW mode, the range of colors in the scene being monitored is tracked continuously, and the white balance is set automatically by an internal micro-controller. If the color range changes constantly, then set the switch to ATW.
KTC-117/217/247 User Manual 4 Installing the Bracket and Camera INSTALLING THE BRACKET AND CAMERA You can mount the camera on a vertical surface (Figure 5), and below (Figure 6) or above (Figure 7) a horizontal surface. Figure 5. Mounting on a vertical surface Figure 6. Mounting below a horizontal surface Figure 7. Mounting above a horizontal surface To mount the bracket see section 4.1. To attach the camera to the bracket see section 4.2. To adjust the camera angle see section 4.3.
Installing the Bracket and Camera 4.1 MOUNTING THE BRACKET 1) Unscrew the mounting plate (Figure 8) from the rest of the bracket. 2) Place the mounting plate against the vertical or horizontal mounting surface and mark the location of the three mounting holes. KTC-117/217/247 User Manual Lock ring Ball and socket bolt Wing nut Optional post extensions Note: The camera comes with fasteners and anchors; use only if they are appropriate for the type of mounting surface.
KTC-117/217/247 User Manual 4.2 Installing the Bracket and Camera ATTACHING THE CAMERA TO THE BRACKET 1) Turn the wing nut (Figure 8) on the bracket counterclockwise to free the ball and socket bolt (Figure 8). See Figure 11. 2) Screw the ball and socket bolt into the bracket hole in the top or bottom of the camera. See Figure 12. 3) Tighten the lock ring (Figure 8) to secure the camera to the ball and socket bolt. See Figure 12. Bracket holes (2) Figure 11.
Installing the Bracket and Camera 4.3 KTC-117/217/247 User Manual ADJUSTING THE CAMERA ANGLE 1) If necessary, turn the wing nut (Figure 8) on the bracket counterclockwise to free the ball and socket bolt (Figure 8). See Figure 11. 2) Swivel the camera on the ball and socket bolt to adjust the camera angle. See Figure 13. 3) Turn the wing nut clockwise to tighten it and secure the camera position. See Figure 14. Figure 13.
KTC-117/217/247 User Manual 5 Making Cable Connections MAKING CABLE CONNECTIONS Note: This camera is 24 VAC only. See Figure 15 and perform the following. 24 VAC power source Power LED indicator To monitor Figure 15. Power and video connections 1) Attach the provided BNC connectors to the ends of the video cable. 2) Connect the video cable to the monitor’s video in BNC connector. 3) Connect the other end of the video cable to the camera’s VIDEO OUT connector.
Making Cable Connections KTC Compact Cameras 4) Loosen the ~AC24V terminal connectors on the terminal block and connect the power cable to them. 5) Tighten the terminal connector screws until snug, ensuring that the power leads are secure. 6) Connect the other end of the power cable to the power supply unit and tighten the connector screws until snug. 7) Supply power to the camera. Note: When you supply power to the camera the PWR LED illuminates.
KTC-117/217/247 User Manual 6 Making Camera Adjustments MAKING CAMERA ADJUSTMENTS To open the housing see section 6.1. To adjust the camera focus see section 6.2. To make direct drive auto iris level adjustments see section 6.3. 6.1 OPENING THE HOUSING See Figure 16 and Figure 17 and perform the following. Grip strips Door Figure 16. Pressing and swiveling the housing door to open Figure 17.
Making Camera Adjustments 6.2 KTC-117/217/247 User Manual ADJUSTING THE CAMERA ZOOM AND FOCUS See Figure 18 and perform the following. Zoom ring thumbscrew Focus ring thumbscrew Figure 18. Adjusting the camera focus 1) Loosen the zoom ring thumbscrew. 2) Turn the zoom ring to set the desired zoom. 3) Tighten the zoom ring thumbscrew. 4) Loosen the focus ring thumbscrew. 5) Turn the focus ring to set the desired focus. 6) Tighten the focus ring thumbscrew. 6.