Specification

Listed by
Underwriters
Laboratories
Specification Revised 2/16
PK7800EK/SK
GE Profile
™
Series 27" Built-In Combination Convection Microwave/Convection Wall Oven
For answers to your Monogram, GE Café
™
Series, GE Profile
™
Series or
GE Appliances product questions, visit our website at geappliances.com
or call GE Answer Center
®
Service, 800.626.2000.
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
MOST 30" WALL CABINETS CAN
BE USED WITH THIS UNIT.
NOTE: These ovens are not approved
for stackable installations. Cabinets
installed adjacent to wall ovens must
have an adhesion spec of at least a 194°F
temperature rating.
Door handle protrudes 3" from door face.
Cabinets and drawers on adjacent 45°
and 90° walls should be placed to avoid
interference with the handle.
Electric wall ovens are not approved for
installation with a plug and receptacle.
They must be hard wired in accordance
with installation instructions.
INSTALLATION INFORMATION:
Before installing, consult installation
instructions packed with product for
current dimensional data.
Side-by-side installations require at
least 2" between cutouts.
KW R ATING
240V 3.6
208V 2.7
BREAKER SIZE
240V 20 Amps†
208V 20 Amps†
20" MIN.
door opening
allowance
CONDUIT
48"
C
L
Suitable
bracing
to support
runners
(must support 275 lbs.)
2 x 4 or
equivalent runners
level with bottom of cutout
and flush with sides of cutout
or solid bottom floor.
B
27''
A
C
CUTOUT WIDTH
25" MIN.
25-1/4" MAX.
Recommended
minimum
cutout location
from the floor
21-5/8"
CUTOUT HEIGHT
41-1/8" MIN.
41-1/4" MAX.
JK3800
PK7800
20"
E
F
D
CABINET 27"
A –Overlap of oven at top of cutout 1"
B – Overlap of oven over side of edges of cutout 3/4"
C –Overlap of oven at bottom of cutout 1"
OVEN
D –Install depth 23-1/2"
E –Overall height with trim 42-3/8"
F –Overall width 26-3/4"
8-3/4" MAX.
RIGHT SIDE ONLY
CUTOUT DEPTH
23-1/2" MIN.
28" MIN. to
bottom of
junction box
Junction box
location
(Junction box
may be located
in adjacent
cabinet)
ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)
into an approved junction box. A plug and receptacle is NOT permitted on these products.
NOTE: If the cabinet does not have a solid bottom,
two braces or runners must be installed to support
the weight of the oven. For single ovens, the runners
and braces must support 200 lbs (91 kg). For double
ovens, the runners and braces must support 375 lbs.
(170 kg).
NOTE: If marks, blemishes or the cutout opening are
visible above the installed oven, it may be necessary
to add wood shims under the runners and front trim
until the marks or opening are covered.
NOTE: If the cabinet does not have a front frame
and the sides are less than 3/4" (1.9 cm) thick, shim
both sides equally to establish the cutout width.
20" MIN.
door opening
allowance
CONDUIT
48"
C
L
Suitable
bracing
to support
runners
(must support 275 lbs.)
2 x 4 or
equivalent runners
level with bottom of cutout
and flush with sides of cutout
or solid bottom floor.
B
27''
A
C
CUTOUT WIDTH
25" MIN.
25-1/4" MAX.
Recommended
minimum
cutout location
from the floor
21-5/8"
CUTOUT HEIGHT
41-1/8" MIN.
41-1/4" MAX.
JK3800
PK7800
20"
E
F
D
CABINET 27"
A –Overlap of oven at top of cutout 1"
B – Overlap of oven over side of edges of cutout 3/4"
C –Overlap of oven at bottom of cutout 1"
OVEN
D –Install depth 23-1/2"
E –Overall height with trim 42-3/8"
F –Overall width 26-3/4"
8-3/4" MAX.
RIGHT SIDE ONLY
CUTOUT DEPTH
23-1/2" MIN.
28" MIN. to
bottom of
junction box
Junction box
location
(Junction box
may be located
in adjacent
cabinet)
ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)
into an approved junction box. A plug and receptacle is NOT permitted on these products.
NOTE: If the cabinet does not have a solid bottom,
two braces or runners must be installed to support
the weight of the oven. For single ovens, the runners
and braces must support 200 lbs (91 kg). For double
ovens, the runners and braces must support 375 lbs.
(170 kg).
NOTE: If marks, blemishes or the cutout opening are
visible above the installed oven, it may be necessary
to add wood shims under the runners and front trim
until the marks or opening are covered.
NOTE: If the cabinet does not have a front frame
and the sides are less than 3/4" (1.9 cm) thick, shim
both sides equally to establish the cutout width.
†
NOTE: Check local codes for required breaker size.