Built-In Wall Oven with Microwave Ilnstallat!on nstruct=ons 27" (68.6 cm) model JKP90 30" (76.2 cm) models JTP90, PT970 If you have questions, call 1.800.GE.CARES ge.com Before You Begin Read these instructions carefully and completely. • IMPORTANT-save instructions these for local inspector's use. • IMPORTANT-observe all governing codes and ordinances. • Note to Installer--Be sure to leave these instructions with the consumer.
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety • Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door. • Make sure the cabinets and wall coverings around the oven can withstand the temperatures (up to 200°F [93.
Installation Instructions Pre-lnstallation Checklist Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: Remove packaging materials. Check inside microwave, behind hinges and under false bottom. Remove labels on the outside of the door, plastic on trims and panel, all tape around the oven and any shipping screws securing the oven to the base pad. like Open the oven door as far as it will go. Push both hinge _..
Installation Instructions IA1Cutout for 27" (68.6cm) Built-In Oven with Microwave models only For JKP90 model only. 5" (12.7 cm) Max.fromthe Cabinet Width left or right Cabinet Width Junction Box Location Recommended Allow 1" (2,5 cm) for overlap of oven over side edges .... of cutout ............ Allow a minimum of 20" (50.8 cm) for clearance to adjacent corners, drawers, walls, etc. when door is open Cutout 35" (88.9 cm) Height Min, Above 41 1/8" base rail eq runners level (104,5 cm) Min.
Installation Instructions Cutout for 30" (76.2 cm) Built-In Oven with Microwave models only For JTP90, PT970 models only. -- Allow 11/16" (1.8 cm) for overlap of oven over side edges of cutout Allow a minimum of 21" (53,3 cm) for clearance to adjacent corners, drawers, walls, etc. when door is Cabinet Width --. 30" (76.2 cm) Cutout Width 28 112" (72.4 cm) Min_ 28 5/8" (72.5 cm) Max, Opening between inside walls must be at least 28 1/2" (72.4 cm) wide open 20" (50.
Installation Instructions Cutout for Built-In Oven with Microwave models only - Over a Warming Drawer For JKP90, JTP90, PT970 models only. 27" (68.6 cm) Oven with Microwave Oven (Model JKP90) Over a Warming Drawer 30" (76.2 cm) Oven with Microwave Oven (Models JTP90 and PT970) Over a Warming Drawer Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement 2" (5,1 cm) Min. Per Warming Drawer Requirement 2" (5.1 cm) Min.
Installation Instructions Electrical Connections ATTENTION Turn off the circuit breaker or remove fuses to the oven branch circuit. INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below.
Installation Instructions IBIElectrical Connections New Construction and Four-Conductor Branch Circuit Connection • When installing in new construction, • When installing in a mobile home, or • When installing in a recreational Three-Conductor Branch Circuit Connection When connecting to a three-conductor circuit, if local codes permit: or vehicle, cont. branch a.
Installation Instructions lcl Securing the Oven in the Opening I_ Sliding the Oven Into the Drilling the Pilot Holes and Mounting the Oven Opening a. Loop (do not tie) a 36" (91 cm) string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered.
Installation Instructions Preparing for the Bottom Trim Installation Installing the Metal Bottom Trim a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. a. b. Using the trim For27" (68.6 cm) models with Lower as a template, Trimin Position, mark the center Mark(2)Mounting Hole Locations of each slot (two total) where the mounting holes will be drilled. c. Remove the trim. d. Drill pilot holes into the center template of each mark.
Installation Instructions Replacing the Oven Door NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. I-_ Open the oven door as far as it will open. r-_ Push the hinge locks up against the front frame of the oven cavity, to the locked position. i Hinge in Locked Position Lift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle.
Installation Instructions Pre-Test Checklist Remove all protective and any stickers. film, if present, Check to be sure that all wiring is secure and not pinched or in contact with moving parts. [_ heck that the bottom trim is installed properly (see page 10). [_ heck to be sure the mounting screws are installed and flush with the side trim (see page 9). Operation Checklist U Remove all items from the inside of the oven.