Installation guide

ManualsBrandsGE ManualsRange hoodOfficial GE range hood

I stallatio

I structios

GJassWalJ

Chimney Vent Hoods

PVW7301, PVW7361

Pl "If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: GEAppliances.com"

BEFORE YOU BEGIN

Read these instructions completely and

carefully.

.IMPORTANT - Savetheseinstructions

forlocalinspector'suse.

,IMPORTANT -Observeallgoverning

codes and ordinances.

, Note to Installer-Be sure to leavethese

instructionswiththe Consumer.

, Note to Consumer - Keep these instructions

forfuturereference.

, Skilllevel- Installationofthisvent hood

requiresbasicmechanical and electricalskills.

, Completion time - Approximately i to 3 hours

, Proper installationisthe responsibilityofthe

installer.

* Product failure due to improper installation is

not covered under the Warranty.

^,,-CAUTION: Due tothe weight and sizeof

thesevent hoods and to reduce the riskof

personalinjuryordamage to the product,TWO

PEOPLE ARE REQUIRED FOR PROPER

INSTALLATION.

FOR YOUR SAFETY:

AWARNING: Beforebeginningthe

installation, switch power off at service panel and

lock the service disconnecting means to prevent

power from being switched on accidentally.

When the service disconnecting means cannot

be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

kLW/'_I_I_i I I_i_: TO REDUCE THE RISK

OF FIRE, ELECTRIC SHOCK OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

A. Installation work and electrical wiring

must be done by qualified person(s) in

accordance with all applicable codes and

standards, including fire-rated construction.

B. Sufficient air is needed for proper

combustion and exhausting of gases

through the flue (chimney) of fuel burning

equipment to prevent back drafting. Follow

the heating equipment manufacturer's

guidelines and safety standards such

as those published by the National Fire

Protection Association (NFPA), the

American Society for Heating, Refrigeration

and Air Conditioning Engineers (ASHRAE)

and the local code authorities.

When cutting or drilling into wall or ceiling,

do not damage electrical wiring and other

hidden utilities.

Ducted fans must always be vented to the

outdoors.

Turn off breaker to adjacent rooms while

working.

A, ,,,^,-., ,,,, ,., ,,'-

_W/4LKi_ilI_i_: TO REDUCE THE RISK

OF FIRE, USE ONLY METAL DUCT WORK.

-4

(991.0364.613revl)31-ii007 04-15 GE

Summary of content (16 pages)

PAGE 1
! I stallatio I structios GJass WalJ Z Chimney Vent Hoods PVW7301, rr- PVW7361 ! Pl "If you have questions, call 800.GE.CARES (800.432.2737) or visit our website O at: GEAppliances.com" Z ! BEFORE YOU BEGIN Read these instructions carefully.
PAGE 2
Z Installation 0 Preparation g PRODUCT INSTALLATION DIMENSIONS CLEARANCES These vent hoods are designed to be installed onto a wall with no above cabinets. 4-15/16" , Install these hoods between the 24" required minimum and 36" recommended maximum above the cooking surface. i0-i Z 0 i _J _J Z 24" Required IVlin. 36" Recommended Max.
PAGE 3
Installation ADVANCE PLANNING POWER SUPPLY Duct Install IMPORTANT- Planning ! Preparation Z I'I-- {Please read carefully} , This hood is designed to be vented vertically through the ceiling. Use a 6" round duct. Use locally supplied elbows to vent horizontally through the rear wall. AWARNING: FOR PERSONAL SAFETY,THIS APPLIANCE MUST BE PROPERLYGROUNDED. O , Use metal ductwork only. , Determine the exact location of the vent hood.
PAGE 4
Z Installation O Preparation g TOOLS AND MATERIALS REQUIRED PLAN THE INSTALLATION (NOT SUPPLIED) A CAUTION: Safety glasses Z Pencil and tape measure O properly exhaust air, be sure to duct the air outside - Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages. PARTS SUPPLIED FOR INSTALLATION i Phillips screwdriver _J _J To reduce risk of fire and to Level .
PAGE 5
Installation ! Preparation Z ¢/) RANGE HOOD COMPONENTS A. B. C. D. E. Canopy Section Upper Duct Cover Lower Duct Cover Mounting Screws Duct Cover Mounting Brackets F, Damper G, Duct Cover Screws H. Mounting Bracket I. Washers J, Canopy Mounting Anchors K. Duct Cover Anchors L. Dry Wall SelfTapping Screws (for Junction Box) INSTALLATION DIMENSIONS The Glass Chimney Hoods are adjustable and designed to meet varying ceiling heights.
PAGE 6
Z O Installation g PREPARE THE WALL Duct Covers Hood Body 1. Place one of the duct cover brackets against the wall so that its top edge is 1/16" from the ceiling and level. Align the center notches of the bracket and the centerline (C) and mark the centers of the bracket holes. Remove the bracket to drill the 2 holes for installation with a 9/32" drill bit, and insert the duct cover anchors. Place the bracket back on the wall and install the 2 mounting screws into the anchors. Tighten screws. 2.
PAGE 7
Installation Instructions ! Z ¢/9 PREPARE HOOD FOR INSTALLATION . Fit the recirculotion I-I-- duct with extensions over the vent exhaust outlet and push down to seat on outlet. Attach the vertical duct work to the Remove the greose filter from the unit and set oside. The greose filter is removed by pressing the handle in front of the filter. When replacing, make sure that the filter is properly positioned with the handles in front and visible. top of the hood.
PAGE 8
Installation Z Instructions O i I-- U l-Z u Z O g MOUNT THE GLASS RANGE HOOD (Continued) FINISH THE INSTALLATION i. Remove the top duct cover bracket from the wall. 5. Align the top edge of the duct cover bracket with the top edge of the recirculation duct mounting bracket that is attached to the recirculation duct. Align the center notches of each bracket. Place both brackets back onto the wall in the previous position. Install the 2 mounting screws into the anchors and securely tighten. .
PAGE 9
! I struccio es de i stal ci6n Z Pared de Vidrio (.t) Campanas de Ventilaci6n PVW7301, de ia Chimenea :x) C PVW7361 N = r_ zPreguntms? Llome ol 800.GE.CARES (800.432.2737) O o visite nuestro sitio Web en: GEApplionces.com Z A^r,, ANTES DE COMENZAR Lea estas instrucciones detenimiento. por completo y con .IMPORTANTE - Guorde estos instrucciones locales. para el uso de inspectores .IMPORTANTE - cumplo contodos los c6digos y ordenanzas Ji/,_uvr_.r_/r_l_bl/..
PAGE 10
Z Preparaci6n para la instalaci6n "O i U <_ _u DIMENSIONES ESPACIO DE INSTALACI6N DEL PRODUCTO <_ Estascampanas de ventilaci6n est6n disefladas para ser instaladas en una pared sin gabinetes superiores. . Instale estas campanas entre el minimo requerido de 24"y el m6ximo recomendado de 36" sobre la superficie de cocci6n. Z i <_ _u <_ 1 <_ Z "O i U <_ I 24" Required IVlin. 36" Recommended Max.
PAGE 11
"0 Preparaci6n para la instalaci6n m "0 PLANIFICACI6N PREVIA SUMINISTRO Planificaci6n para la Instalaci6n con Conducto , Esta campana est6 diseBada para ventilarse en forma vertical a trav6s del cielorraso. Use un conducto circular de 6". Utilice codos suministrados en forma local para ventilaci6n horizontal a trav6s de la pared trasera. , Determine la ubicaci6n exacta de la campana de ventilaci6n. , Planifique el recorrido de la salida de ventilaci6n hacia el exterior.
PAGE 12
Z Preparaci6n para la instalaci6n "O i HERRAMIENTAS _J REQUERIDOS Y MATERIALES J (NO SUMINISTRADOS) APRECAUCION: I-Z Gafas de seguridad i _u PLAN DE INSTALACI6N A finde reducir riesgos de incendios y para que el aire salga de forma apropiada, aseg_rese de que el aire sea conducido hacia fuera - No ventile el aire de la salida hacia espacios dentro de paredes o cielorrasos o 6ticos, espacios muy bajos o garajes.
PAGE 13
"0 Preparaci6n para la instalaci6n m "0 COMPONENTES E×TRACTORA DIMENSIONES DE LA CAMPANA A. Secci6n de la Base B. Cubierta del Conducto Superior C. Cubierto del Conducto Inferior D. Tornillos de Nontaje E. Soportes de Montaje de la Cubierta del Conducto F. Regulador G. Tornillos de la Cubierta del Conducto H. Soporte de Montoje I. Arondelus J. Soportes de Montoje de la Base de la Campana K. Soportes de la Cubierta del Conducto L.
PAGE 14
Z "O Preparaci6n para la instalaci6n i U _J PREPARE LA PARED Cubiertas Corriente I-- Cuerpo de la Campana Z 1. Coloque una cubierta protectora sobre la superficie debajo de la ubicaci6n de la campana, a fin de proteger de la suciedad y/o daflos. i _J tZ. Z "O i 2. Determine y marque la linea central sobre la pared (dibuje la linea hacia arriba hasta el cielorraso) donde la campana extractora ser6 instalada.
PAGE 15
! Instrucciones de instalaci6n Z --I PREPARE LA CAMPANA INSTALACION PARA SU Retire el filtro de grasa de la unidad y deje el mismo a un lado. El filtro de grasa es retirado presionando la manUa que se encuentra frente al filtro. AI realizar el reemplazo, aseg6rese de que el filtro est6 correctamente posicionado con las manijas en el frente y visibles. Inserte el conducto de recirculaci6n con extensiones C sabre la sulidu del escape de ventiluci6n y empuje huciu ubujo puru que coincidu con lu sdlidu.
PAGE 16
Z Instrucciones de instalaci6n "O i _J MONTE LA CAMPANA EXTRACTORA DE VIDRIO (contin6a) l-- Retire de la pared et soporte superior de la cubierta det conducto. Of) Z Alinee et extremo superior del soporte de la cubierta det conducto con et extremo superior det soporte de montaje det conducto de recirculaci6n, et cual est6 adherido al conducto de recirculaci6n. Alinee las ranuras centrales de cada soporte. Vuetva a colocar ambos soportes en la pared, en la posici6n previa.