Installation guide

ManualsBrandsGE ManualsMotorcycle AccessoriesRH30

DIMMING

SWITCH

DIMMING SWITCH

Dimming

Dimming Enabled (20%)

Dimming Disabled (default)

• For retrot, place LED driver in the location where the ballast was formerly located.

• Make output (DC) connections as noted below:

• Make input (AC) connections using one of the two options below:

• The LED Driver is required to be reliably bonded to the protective ground conductor.

Connect LED Driver - Output

Connect LED Driver - Input

Dimming /Occupancy Sensor Contacts – Output (Optional)

OPTION 1 (OEM) – USING 4-WAY CONNECTOR

OPTION 1 (OEM) - USING 3-WAY CONNECTOR

OPTION 1 (OEM) - USING 4-WAY CONNECTOR

OPTION 2 (OEM or RETROFIT) – USING TWIST-ON WIRE

CONNECTORS

OPTION 2 (OEM or RETROFIT) – USING TWIST-ON WIRE

CONNECTOR

OPTION 2 (OEM or RETROFIT) – USING TWIST-ON WIRE

CONNECTORS

Connect the LED Driver output leads to the LED Light leads

using the appropriate mating connector (Molex P/N 39-01-

4046). Terminals installed should be crimped using approved

tooling and process per Molex specications. Ensure that the

connector cavities are correctly populated per the

wire cavity table on page 3.

Attach the supplied green/yellow ground wire from the

LED Driver to a grounded metal portion of the door frame.

Connect the original Line and neutral wires (or Line 1 and

Line 2 wires for 240 nominal VAC) to the 3-way connector

for the LED Driver input wires using the appropriate mating

connector (Molex P/N 39-01-4030). Ensure that the

connector cavities are correctly populated per the

wire cavity table on p. 3.

Connect the LED Driver dimming output leads to the

occupancy sensor or control system using the appropriate

mating connector (Molex P/N 39-01-4046). Terminals installed

should be crimped using approved tooling and process per

Molex specications. Ensure that the connector cavities are

correctly populated per the wire cavity table on page 3.

Remove the 4-way connector from the LED Driver by

cutting the wires near the connector and strip the output

leads. Using the appropriate wiring diagram on page 3,

connect the LED Driver output leads to the LED Light leads

using wire connectors or other connection method approved

for low temperature usage and stranded cable.

For non-dimming applications, cap the unused wires with

5/32” (4mm) twist on wire connectors.

For Retrot: Bundle and safely secure any unused wires by

way of approved wire ties and wire connectors.

Attach the supplied green/yellow ground wire from the LED

Driver to a grounded metal portion of the door frame.

Remove the 3-way connector from the LED Driver by cutting

the wires near the connector and strip the input wires. Using

the appropriate wiring diagram on page 3, connect the

original Line and neutral wires (or Line 1 and Line 2 wires for

240 nominal VAC) to the LED Driver leads using twist lock

wire connectors or other connection method approved for

low temperature usage and stranded cable. Ensure that the

connector cavities are correctly populated per wire cavity

table on p. 3.

Remove the 4-way connector from the LED Driver by

cutting the wires near the connector and strip the output

leads. Using the appropriate wiring diagram on page 3,

connect the LED Driver dimming output leads to the

occupancy sensor or control system using wire connectors

or other connection method approved for low temperature

usage and stranded cable.

• To enable dimming operation and/or occupancy sensors you must connect leads from occupancy sensor or control system

(normally open contact) to the purple and gray leads of the power supply and adjust dimming switch as shown below.

Note: connection of occupancy sensor to the dimming leads will reduce light output to 20% normal output.

• Make output (contact closure) connections as noted below:

• The GEPS6500NCMUL-SY LED Driver is capable of step

dimming from 100% power to 20% power when used with a

normally open contact closure occupancy sensor system.

• When using the GEPS6500NCMUL-SY for dimming

applications, the dimming switch setting must be switched to

the left to enable the dimming feature. The following is the

only recommended usage of occupancy sensors with the

Immersion LED lighting system. Other methods, such as using

occupancy sensors to switch the LED driver on and off is not

recommended and will void the product warranty.