Installation Instructions

ManualsBrandsGE ManualsCircuit Protection & Power DistributionPowerMark Gold 200-Amp 20-Space 40-Circuit Outdoor Raintight Main Breaker Load Center

INDOOR TYPE

General

To comply with the National Electrical Code and Underwriters Laboratories, the

load center must be installed in accordance with the information included on the

label on the inside of the equipment. This must also be done in accordance with

applicable local electrical codes, and by a qualified electrical contractor and/or

licensed electrician.

WARNING: Hazard of electrical shock or burn. Turn off power before working

inside this equipment.

1. Remove Front :

Slip front and accessory package back into carton to protect

finish.

- Back Out Mounting Screws ”M” & green ground-bonding screw “G” and save for

reuse.

- Slide Interior up to clear tabs and remove.

2. Remove Interior (optional)

Key-hole

Mounting holes

Remove oblong KO

and screw (both

sides)

TOP OR BOTTOM FEED

3. Mount Box

- For Flush Mount, line up front box edge with finished wall surface and mount on

sides through oblong KO as shown above using screws

- For Surface Mount, screw or nail through keyhole slot and mounting holes in back of

box as shown above

The load center will easily accommodate

incoming electrical service from the top

or bottom. Rotate the entire load center

enclosure if a bottom feed configuration is

required.

First knock center KO inward. Outer rings should be alternately pried up or

driven in one at a time.

4. Remove KO’S for all main and branch circuits.

5. Pull incoming service and branch circuit wiring into box

6. Replace interior

Reinstall mounting screws removed in Step 2.

7. Wire main, neutral, and equipment ground

Refer to rating label inside equipment for proper tightening torque. Equipment ground

is factory installed. Wire the ground and neutral as shown below.

For use as service equipment, terminate the grounding electrode to any neutral

terminal. Bond neutral to box as shown below.

Neutral

terminals

Equipment

Ground

terminals

AdditionalTGL2

Ground-kit

location

Bond neutral to box

using screw provided

Note: For additional equipment-ground, please order Equipment-Ground kit (TGL2)

PowerMark Gold ™Load Centers

Summary of content (4 pages)

PAGE 1
g PowerMark Gold ™Load Centers INDOOR TYPE General To comply with the National Electrical Code and Underwriters Laboratories, the load center must be installed in accordance with the information included on the label on the inside of the equipment. This must also be done in accordance with applicable local electrical codes, and by a qualified electrical contractor and/or licensed electrician. WARNING: Hazard of electrical shock or burn. Turn off power before working inside this equipment. 1.
PAGE 2
8. Install Main-Breaker Lock-down For Main Breaker Application, Lock-down kit (THQLRK3) must be installed as shown: Lock-Nut Retainer-Clip for MainBreaker 10. Remove cover KO’s Remove only enough knockouts to match the number of circuit breakers installed.
PAGE 3
g Para interiores Centros de carga PowerMark Gold ™ General Para cumplir con el Código Eléctrico Nacional (National Electrical Code) y los Laboratorios Aseguradores (Underwriters Laboratories), el centro de carga debe instalarse de acuerdo con la información incluida en la etiqueta que se encuentra en el interior del equipo. Esto debe hacerse también siguiendo los códigos eléctricos locales aplicables y debe ser realizado por un contratista eléctrico calificado o un electricista certificado. 4.
PAGE 4
8. INSTALE EL INTERRUPTOR TERMOMAGNETICO DEL INTERRUPTOR PRINCIPAL Para las aplicaciones con interruptor principal, se tiene que instalar el juego para bloqueo THQLRK3 como se muestra. Retenedor de empuje Clip de retención del interruptor principal 10. Retire las pestañas de los orificios Retire solo las pestañas suficientes para igualar el número de interruptores de circuitos instalados.