UCG1500 UCG1600
49-80512 Rev. 4
Installation Instructions
INSTALLATION—VENTED TO THE OUTSIDE
4
MOUNT THE HOOD
WARNING
2 people are required to lift and
position the hood onto the mounting screws.
Ŷ/LIWWKHKRRGRQWRWKHPRXQWLQJVFUHZV
Ŷ&KHFNOHYHODQGPDUNERWWRPVFUHZORFDWLRQV
Ŷ5HPRYHWKHKRRG
Ŷ'ULOOSLORWKROHVLQWKHPDUNHGORFDWLRQ
Ŷ,ISLORWKROHVGRQRWHQWHUVWXGVHQODUJHWKHKROHVWR
DQGLQVWDOOPHWDOZDOOIDVWHQHUDQFKRUVSURYLGHG
Ŷ/LIWWKHKRRGRQWRWKHPRXQWLQJVFUHZV
Ŷ,QVWDOOORZHUVFUHZVWRSXOOWKHKRRGWLJKWDJDLQVW
the wall.
Ŷ7LJKWHQWKHWRSPRXQWLQJVFUHZV
2
INSTALL HOOD MOUNTING
SCREWS
The two upper mounting screws must enter the
horizontal support or wall studs.
Ŷ:LWKWKHWHPSODWHWDSHGLQSODFHXVHDSXQFKWR
mark mounting bracket screw locations.
Ŷ'ULOOSLORWKROHVLQRIWKHSXQFKHGORFDWLRQVLQ
the lower bracket.
Ŷ5HPRYHWKHWHPSODWH
Ŷ,QVWDOOWKHPRXQWLQJVFUHZVOHDYHJDS
between the screw head and the wall. This will
allow the keyhole slot on the hood frame to engage
the screw head.
IMPORTANT: Use the mounting screws provided. DO
12786('5<:$//6&5(:6
Ŷ&KHFNWREHVXUHWKHPRXQWLQJVFUHZVDUH
horizontally level.
3
INSTALL DUCT BRACKET
The duct bracket should be installed against the back
wall and flush with the ceiling. This bracket will hold
the duct cover in place at the top.
Secure the bracket to the wall:
Ŷ$OLJQWKHGLDPRQGFHQWHUOLQHFXWRXWRQWKHEUDFNHW
with the penciled centerline on the wall.
Ŷ0DUNVFUHZKROHORFDWLRQVLQWKHZDOO
Ŷ'ULOOSLORWKROHVLQWKHPDUNHGORFDWLRQV
Ŷ,ISLORWKROHVGRQRWHQWHUZRRGVWXGVHQODUJHWKH
KROHVWRDQGLQVWDOOPHWDOZDOOIDVWHQHUDQFKRUV
(provided).
Ŷ,IPRXQWLQJGLUHFWO\WRDPDVRQU\ZDOOREWDLQ
DSSURSULDWHPDVRQU\VFUHZDQFKRUV'ULOODQG
install per the fastener supplier’s instructions.
Ŷ'ULYHVFUHZVE\KDQGLQWRWKHIDVWHQHUVWRDOORZ
DQFKRUVWRH[SDQG5HPRYH
the screws.
Ŷ6HFXUHWKHEUDFNHWWRWKH
wall with wood screws
and/or fasteners.
Installation Height
Align Bottom Edge With
Pencil Line Indicating
Bottom of Hood
REAR WALL
MOUNTING TEMPLATE
49-80514 10/07 JR
Printed in Mexico
15-7/16″
15-7/16″
10-1/16″
C
L
1-1/4″
1-1/4″
9-7/16″
9-7/16″
TOP
MOUNTING
HOLE
DRILL 1/8″
PILOT HOLE
TOP
MOUNTING
HOLE
DRILL 1/8″
PILOT HOLE
BOTTOM
MOUNTING
HOLE
BOTTOM
MOUNTING
HOLE
NOTE:Top
mounting
screws MUST
engage wood
support.
NOTE: Top
mounting
screws MUST
engage wood
support.
Installation Height
Align Bottom Edge With
Pencil Line Indicating
Bottom of Hood
Centerline
cutout
Tighten
screws
Install
screws