Installation Guide

40 31-7000188 Rev. 0
Instrucciones de Instalación
2. TIPOS DE INSTALACIÓN (Escoja A, B o C)
C. VENTILACIÓN EXTERIOR TRASERA (Conducto Horizontal)
VISIÓN GENERAL DE LA INSTALACIÓN
C1. Prepare la Pared Trasera
C2. Adjunte la Placa de Montaje a la Pared
C3. Prepare el Gabinete Superio
C4. Retire el Plato Calentador
C5. Adapte la Dirección del Aire del Microondas para
que cuente con Salida Trasera Hacia el Exterior
C6. Monte el Horno Microondas
C1. PREPARACIÓN DE LA PARED
TRASERA PARA EL ESCAPE
EXTERNO TRASERO
Es necesario cortar una abertura en la pared trasera del
escape externo.
• Lea las instrucciones sobre la PLANTILLA DE LA
PARED TRASERA.
• Pegue la misma a la pared trasera, alineándola con los
agujeros previamente perforados A y B en la placa de
montaje.
• Corte la apertura, siguiendo las instrucciones de la
PLANTILLA DE LA PARED TRASERA.
C2. ADHIERA LA PLACA DE MONTAJE A
LA PARED
Adhiera la placa a la pared usando tornillos con
resortes. Por lo menos un tornillo de madera deberá ser
usado para adherir la placa al montaje de pared.
1. Retire las tuercas mariposa de los tornillos.
2. Inserte los tornillos en la placa de montaje a través
de los agujeros designados para entrar en la placa de
yeso y vuelva a ajustar las tuercas mariposa a 3/4”
sobre cada tornillo.
Para usar tornillos con resorte:
3. Coloque la placa de montaje contra la pared e inserte
las tuercas mariposa en los agujeros de la pared para
montar la placa
PRECAUCIÓN
Tenga cuidado para evitar
pellizcos en los dedos entre la parte trasera de la
placa de montaje y la pared.
4. Ajuste todos los tornillos. Empuje la placa hacia afuera
de la pared para ayudar a ajustar los tornillos.
A
C
D
B
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
12"
4"
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
NOTE: It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE:: DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Darle vuelta a la hoja para consultar la
versión en Español.
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
30” MINIMUM WIDTH REQUIRED
REAR WALL TEMPLATE
F. CUT OUT FOR HORIZONTAL
OUTSIDE EXHAUST
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall template along the dotted line.
3/8" TO EDGE
C
A
C
D
B
NOTES:
- 13” Max Cabinet Depth
- 15” deep cabinets require additional steps using
an additional installation kit: JX36BUMP
OPTION 1
OPTION 2
STEP 1: Installer uses bracket to make 2 marks. First
mark is made by using the stampled slot in bracket.
Second mark is made on the ouside edge of bracket.
STEP 2: Installer moves bracket to the other side of
the cabinets and makes 2 more marks. Marks are the
same as STEP 1, just opposite side.
STEP 4:
Make a mark here, along
inside bottom of the
stamped slot provided.
Make a mark
here,
even with
bottom of
stamped
slot
Make a mark here, along
inside bottom of the
stamped slot provided
(same as Step 1).
Make a
mark here,
even with
bottom of
stamped
slot
Horizontal line
A
C
D
B
A
C
D
B
Pared
Placa de
Montaje
Espacio para Tornillos con Resorte
Superior al Grosor de la Pared
Tornillo con
Resorte
Tuercas Mariposa
Extremo del Tornillo