Installation guide

ManualsBrandsGE ManualsLaundry centerOfficial GE washer/dryer laundry system

WSM2480

24" (61 CM) GAS WASHER/DRYER

INSTALLATION INSTRUCTIONS

Table

WASHER/DRYERSAFETY..............................I

INSTALLATIONINSTRUCTIONS....................3

Tools and Parts .............................................3

Alternate Parts...............................................3

Location Requirements.................................3

DrainSystem .................................................4

ElectricalRequirements ................................5

Gas Supply Requirements............................5

Venting Requirements...................................6

InstallLeveling Legs......................................7

of Contents

RemoveFoam Packing.................................8

Connect Drain Hose......................................8

Connect Inlet Hoses......................................9

Secure Drain Hose........................................9

PlanVent System ........................................10

InstallVent System......................................11

LevelWasher/Dryer.....................................11

Make Gas Connection ................................11

ConnectVent ..............................................11

Complete Installation ..................................12

WASHER/DRYERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions.

You can be killed or seriously injured if you don't follow

instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

iMPORTANT SAFETY iNSTRUCTiONS

When discarding or storing your old clothes dryer, remove the door.

SAVE TH ESE iNSTRUCTiONS

8577220

Summary of content (12 pages)

PAGE 1
WSM2480 24" (61 CM) GAS WASHER/DRYER INSTALLATION INSTRUCTIONS Table of Contents WASHER/DRYER SAFETY..............................I INSTALLATIONINSTRUCTIONS....................3 Tools and Parts .............................................3 Alternate Parts...............................................3 Location Requirements.................................3 Drain System .................................................4 ElectricalRequirements ................................5 Gas Supply Requirements ......
PAGE 2
WARNING: For your safety, the risk of fire or explosion, the information or to prevent in this manual must be followed property - Do not store or use gasoline or other flammable or any other appliance. - WHAT TO DO IF YOU SMELL damage, personal to minimize injury, or death. vapors and liquids in the vicinity of this GAS: • Do not try to light any appliance. • Do not touch any electrical switch; do not use any phone in your building. • Clear the room, building, or area of all occupants.
PAGE 3
INSTALLATIONINSTRUCTIONS A Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. , Rsds Your installation may require additional parts. For ordering information, please refer to the Use and Care Guide. If You Have You Will Need to Buy Laundry tub or standpipe taller than 96" (2.4 m) Sump pump system (if not already available) Tools needed:.
PAGE 4
• Alevelfloorwithamaximum slopeof1"(2.5cm)underentire washer/dryer. Clothes maynottumble properly andautomatic sensor cyclesmaynotoperate correctly ifwasher/dryer isnot level.Installing oncarpetisnotrecommended. • Awaterheater settodeliver 120°F (49°C) watertothewasher. • Hotandcoldwaterfaucets located within4ft (1.2m)ofthe hotandcoldwaterfillvalves, andwaterpressure of5-100psi (34.5-689.6 kPa). Thewasher/dryer mustnotbeinstalled orstored inanareawhere itwillbeexposed towaterand/orweather.
PAGE 5
Laundry tub drain system (view C) The laundry tub needs a minimum 20 gal. (76 L) capacity. The top of the laundry tub must be at least 34" (86.4 cm) above the floor and no higher than 96" (2.4 m) from the bottom of the washer. Floor drain system (view D) The floor drain system requires a siphon break that may be purchased separately. See "Alternate Parts." The siphon break must be a minimum of 28" (71 cm) from the bottom of the washer. Additional hoses might be needed.
PAGE 6
LP gas conversion: Conversion must be made by a qualified technician. No attempt shall be made to convert the appliance from the gas specified on the model/serial rating plate for use with a different gas without consulting your gas company. Burner input requirements: Elevations up to 10,000 ft (3,048 m): • Gas supply line • 1/2"IPS pipe is recommended. • %" approved tubing is acceptable for lengths under 20 ft (6.1 m) if local codes and gas supplier permit. • Lengths over 20 ft (6.
PAGE 7
• 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. Exhaust Recommended hood styles are shown here. B 4" (10.2cm) heavymetal exhaust vent Rigid metal vent • For best drying performance, rigid metal vents are recommended. • (10.2cm) A. Louvered hood style B. Box hood style Rigid metal vent is recommended to prevent crushing and kinking. The angled hood style (shown here) is acceptable. Flexible metal vent • Flexible metal vents are acceptable only if accessible for cleaning.
PAGE 8
2. Check adjustability of rear legs by pushing in one leg. The other leg should come out. Check both legs. If they do not move freely, repeat Step 1. 3= Squeeze ears of the silver, double-wire clamp with pliers to open. Place clamp over the straight end of the drain hose 1A" (6.4 mm) from the end. Install the front leveling legs 1. Examine the front leveling legs. Find the diamond marking. 2. Screw front legs by hand, into the holes in the triangular braces in the front corners.
PAGE 9
NOTE: Do not overtighten or use tape or sealants on the valve, Damage to the valves can result. Insertanewflatwasher (supplied) intoeachendoftheinlet hoses. Firmly seatthewashers inthecouplings. A B If you are working in a closet or recessed area Move the washer/dryer into its final position and remove cardboard from under washer/dryer. Remove the access panel by removing three Phillips-head screws and one bumper, located at the top of the access panel. Set panel, screw, and bumper aside.
PAGE 10
Refer to the manufacturer's system. Choose your exhaust installation type instructions provided with the vent Recommended exhaust installations Typical installations vent the dryer from the rear of the washer/ dryer. Other installations are possible. j_[ ....... , t ...... ,,, ( • ( "%.......... ,\ ....... "\ ,\j A ........... ( \j ........ ......... B A. Loop system with standard elbows B. Loop system with one offset and one standard elbow C.
PAGE 11
Determine vent length and elbows needed for best drying performance 1= • Use the Vent system chart below to determine type of vent material and hood combinations acceptable to use. 2. NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those specified will: 3= • Shorten the life of the dryer. • Reduce performance, resulting in longer drying times and increased energy usage. Remove the red cap from the flexible gas connector.
PAGE 12
1. 2. 3. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. Check that you have all of your tools. 13. To test the dryer, set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer. If the dryer will not start, check the following: Dispose of/recycle all packaging materials. Keep the plastic foam for use if the washer/dryer should be transported. Check the washer/dryer's final location.