Installation Instructions Built-In Dishwashers ZBD6400,ZBD6500,ZBD6600 ZBD6700,ZBD6900,ZBD7000, ZBD7100 Chef's Washers ZBD6605,ZBD6905,ZBD7005, ZBD7105 Design Guide with Installation Instructions Monogram: We bring good things to life.
Safety Information BEFORE YOU BEGIN • IMPORTANT be installed Read these instructions completely • IMPORTANT mid carefully. Skill Level basic is the failure due under the and responsibility to improper • Completion tions require tions. of this electrical instruc- dishwasher skills, of the GE Applimace these - Keep these instructions tot flltm'e reterence.
Design Information PRODUCT DIMENSIONS ADVANCE 34" Adjustable to 35" DISHWASHER Traditional *Dishwasher model ZBD7000 and Chef'sWasher model ZBD7005 require a 3/4" thick custom panel and will be 24-3/4" deep. PLANNING • These dishwashers are designed flw versatility, adaptable to vh'tually any installation.
Installation MATERIALS Materials Preparation YOU WILL NEED: Required ©G @ for All Installations Screw Type Clamps [] 90° Elbow (3/8"NPT external thread on one end, opposite 90° Elbow end sized to fit water supply) Note: Use new ferrule. Do not use old parts.
Installation Preparation PARTS SUPPLIED: Remove fl'om Check parts the inside hardware or taped contents are accessory to the against bag outside and other of the illustrations parts I dishwasher.
Installation Preparation DRAIN REQUIREMENTS Method 1 - Air Gap with Waste Tee or Disposer An air gap must be used when the waste tee or disposer connection is less than 18" from the floor. • Follow local codes and ordinances. • Do not exceed ] 0 feet distance to drain. • To prevent back flow into the dishwasher, COlmect drain line to an air gap or use a 30" high drain loop, depending on local codes.
Installation Preparation PREPARE ELECTRICAL WIRING FOR PERSONAL SAFETY: Remove house fllse or open circuit breaker before begimfing installation. Do not use an extension cord or adapter plug with this appliance. POUR ASSURER PERSONNELLE, LA S1_CURIT1_ ou couper le courant axant de commencer r Electrical au disjoncteur l'installation. cet appareil, il ne taut pas utiliser ralhmge ni d'adaptateur de prise. de Black Electrical must be supplied with 120V, 60 Hz.
Installation Preparation PREPARE HOT WATER LINE The line may enter fl'om either within the shaded area shown. side, rear or floor • The water line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional l-1/2" dia. hole to admit the line. If a power cord with plug is used, a separate hole. i\ / it must / i \ \ Shut-offValve \ pass through ,,_ ii ii Water Hot[]:::: Line Connection ii ii ii • Turn o11 the water supply.
Custom Panel Dimensions CUSTOM PANEL FOR MODELS ZBD6400 ONLY Panel kits must be ordered separately. Installation of any custom panel should be completed before the dishwasher is installed. 1/4" PANEL WITH ZPF625 TRIM KIT CUSTOM PANEL FOR MODELS ZBD7000 AND ZBD7005 These models require a field installed 3/4" thick custom panel and CtlStOlll handle. An installation template is packed with these models and may be obtained in advance. Order Pub. No. 49-5919. See page 15 for panel installation instructions.
Installation Instructions lSTEP31REMOVE BEFORE YOU BEGIN: CUSTOM PANEL INSTALLATION: Ifvou intend ACCESS COVER to install custom door panels, (on some models) refer to trim kit installation instructions. Custom panels should be in place bet0re installing tile dishwasher. ISTEP 1] REMOVE PACKAGING Cut tile shipping carton and use it as a pad beneath tile dishwasher. This will protect tile finished floor in tile kitchen.
Installation Instructions [STEP 5] INSTALL POWER CORD [STEP 7] SLIDE DISHWASHER INTO OPENING SKIP THIS STEP IF DISHWASHER WILL BE DIRECT WIRED DO NOT PUSH • Maxim mn power cord length is 6 ft. • The power cord and connections must comply with the National Electrical Code, Section 422 and/or local codes and ordinances. KNEES, AGAINST DAMAGE WILL THE FRONT PANEL WITH OCCUR! • Insert draii_ hose into the cabinet wall hole. If a power cord is used, guide the end through a separate hole.
Installation [STEP 9] CONNECT Instructions DRAIN LINE [STEP 101 CONNECT ELECTRICAL FOLLOW ALL LOCAL CODES AND ORDINANCES. FOR DIRECT WIRE ONLY (If a power • The dishwasher is supplied with a 72" long drain hose. • If a hmger drain hose is required, add up to 48" of length for a total of ] 0 ft. length. • Secure the drain hose to the air gap, waste tee or disposer with damps. • Make sm'e drain hose is not kinked.
Installation Instructions I STEP 111 POSITION AND LEVEL THE DISHWASHER • Check to be sure tile dishwasher is a(!justed to correct height and is centered in tile ctltotlt. • Open and close tile door to insure proper operation tile door. If there is any binding or rubbing, rea(!just leveling DoorRub Door OnRight OnLeft of Adjust This Leg legs. Use a wrench to make adjustments. • If the door rubs on the right side of the cabinet, extend the left rear leg by unscrewing it one quarter turn.
Installation Instructions [STEP 14] SECURE DISHWASHER TO CABINET AND COUNTERTOP To maintain position and aligmnent, the dislmashei must be secured to the countertop and ac!jacent cabin ets. Secure dishwasher to countertop: • Drill pilot holes through the motmting into the ui_derside of the coui_tertop. [STEP 151 INSTALL TOEKICK • Loosen depth ac!j ustm ent screws inside the bracket. • Slide bracket out _ Depth to proper depth. Tighten screws.
Panel Installation for Models ZBD7000 and ZBD7005 The custom panel should be prepared by your cabinet manufacturer according to the instructions shown on page 9. Use the supplied installation template to locate the mounting screws for the door. [STEP 4] INSTALL CUSTOM Screws Must Be Countersunk Into Panel | E_ HANDLE '_4-1/2" Max. FromTop of Panel ISTEP 11DRAW Handle CENTERLINE • Place the custon] fiat sm'thce side down.
Note: While performing installations described in this book, safety glasses or goggles should be worn. For Motion'ram 1-800-444-1845. TM local s_,r_,ice i_ )our area, call Note: Product improvement is a continuing endeavor at General Electric. ThereIore, materials, appearance and specifications are sul)ject to change without notice. Monogram: General Electric Company Louisville, KY40225 0616400 327 Pub.No.49-5905-2 Dwg.No. 165D4700P231 (N.D.
