Manual

Control Panel/Operation - ZBD6905
( h_(/'_ Washer
3. SMART DRY-_4'hen selected, sensors detect the presence of rinse aid and the final rinse
temperature. The drying heater and tim are then turned on fin" the minimum time to achieve
optimum drying results, saving energy over conventional heated d_T and time over non-heated
dry. SMART DRY is not available on RINSE ONI,Y.
4. WATER TEMP-This button provides extra heat options to increase water temperature for
optimum l)erfiwmance.
NORMAL
HIGH
SAN1
This is the dethult setting-provides a wash and rinse with water temperatures
up to 195°F (51°(:) in the I,IGHT _4;€SH, 135°F (57°C) in the NORMAl,
_'__SH cycle and 155°F (68°C) in HEAW DUTY.
This water temp selection provides a wash and rinse with water temperatures
up to 160°F (71°C) in I,IGHT X_]__SH, NORMAI, WASH and HEAVY DUTY.
Use this option fin" heavily soiled dishes. Cannot be used with RINSE ONI,Y.
This water temp selection provides a sanitizing wash and rinse with water
temperatures up to 160°F (71°C) in I,IGHT _?tSH and I71°F (77°C) in
NORMAl, X_;A_SHand HEAVY DUTY. Cannot be used with RINSE ONI,Y.
At the end of the _4%_SH cycle, the SANI OPTION light will remain illuminated
to indicate that the sanitization conditions have been met.
NSF INTERNATIONAL
Meets NSF Protocol for Performance of Domestic Spray-Type Pots
and Pans h'ashing Machines (NSF Protocol P180) Requirements for
cleaning and sanitization of cookware.
NOTE: NSF certified residential dishwashers are not intended fin"licensed tood establishments.
5. DELAY START-This option will allow wm to delay the start time of any wash cycle except
RINSE ONIN fi_r up to 6 hours.
1. Select the delay start time wm want by pressing the DELAY START button. Multiple pressing
will alternate the delav time between 2, 4 or 6 hours and OFE
2. The last programmed cycle will automatically be selected. A new cycle and options can also
be selected. The DELAY START light/lights will flash to indicate time selected.
3. The flashing Delay Start Indicators show how many hom_ will elapse befln'e washing begins.
Start a
wash load
To start the Chef's Washer, close the door until it loc!<s in place. The last used cycle will be displayed.
To begin this cycle, push the START button. To select a ditti_rent cycle, push the desired Cycle
Selection and Option buttons, and then press the START button.
The door must be closed and latched into place to select a cycle or an option.
To interrupt/pause a cycle, press the selected cycle button. The Stares Indicators will flash.
CAUTION: Be carefid when opening the door; the hot steam that escapes when the door is
opened mav cause ii_juries. Stand back as vou open the door and allow the steam
to escape.
_ATTENTION : Faites attention hn_que xous ouxrez la porte. I,a xapeur brfilante qui s'_chai_pe
hn_que vous ouw'ez la porte pendant un programme de lavage peut causer des
b_filures. I,orsque vous ouwez la porte, reculez et laissez la vapeur s'_chal)per
de l'appareil.
To restart the wash process, close the door until it locks in place. Re-press the cycle button. There
may be a time delay of up to a tew minutes, because the temperature inside the Chef's _'asher
needs to stabilize bet0re it restarts the wash cvcle. During this time the SENSING light will be on.
To cmlcel the cycle atter it has started, press and hold the START/CANCEI, button for 3 seconds.
The Chef's X_asher will then drain and the cycle indicator lights will flash. At this point a new wash
cycle can be selected. If a new cycle is not selected, all the Cycle Indicator lights will go out atter the
Chef's Washer drains. If win have selected a new wash cycle, remember to add more detergent to
the detergent compartment if required.
11