GE Monogram ® Installation Instructions 27" Built-In Models ZEK 75 7WW ZEK 75 7B W ZEK737WW ZEK 73 7B W Ovens
Before you begin--Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector's use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Constlmer. NOTE TO CONSUMER: Keep these instructions Book for flmJre reference. This appliance If you tion have questions of this Center be properly must concerning product, call < Consumer 800.626.
Design Information Built-In Models available Ovens ZEK 75 7 WW Whitedouble convectionoven r---q ZEK757BW Blackdoubleconvectionoven ZEK73 7WW Whitesingle convectionoven ZEK737BW Black single convection oven With both rary single Monogram custom double • Built-in single • Monogram Dimensions Double oven and A- 20" (508 mm) clearances , double offer built-in an array styles, contempo- of choices for the kitchen: • Built-in cated and ovens black A convection convection bui
Design Information Built-In Cabinet Ovens style options FrontFramedPartial OverlayDoor Monogram wall ovens oven surface of the rounding cabinet here fit. are cabinetry, ovens will cabinetry. cutouts be nearly styles instructions cabinetry styles are Designer Note: Whenever into width. flush The provided each in this or fi'ont sui'- appearance, examples of 27" cabinets for a wall The with optimal be exact.
Design Information Built-In Ovens Installation options Single Oven Installed Below A ZMC1090WV/ZMC1090BVM icrowave Oven ...... 27" ...... t Single Oven Installed Below A ZEM200WV Microwave Oven 23-5/8" Min. 1 16-3/8" Excluding Handle / 1-7/8.......... Min. 8 j16 i 27-1, 45-1/4"- .... to Top 1-7/8..... Mio, ii Surface of Plywood Base _. toTop Surface of Plywood Base _ / 15-5/8" Min. 24_7/1_,,_T.
Cabinetry Built-In Tools and materials required • 2" x 4" lumber for runners Ovens are designedfor installation in a cabinet 27" min, wide, • Saw • Cut 2" x 4" runners of appropriate length or solid shelf to • Level support oven, • Phillips screwdriver and wood screws or other hardware for installing runners or shelf to support oven, Framed double Ovens • Attach runnersor solid shelf in opening as shown, • Runnersmust be level and rigidly mounted, cabinet oven FrontFramed Front FramedFull P
Cabinetry Built-In Framed single Ovens cabinet oven Allow 7/8" Overlap on Sides and Bottom. Allow 1/4" Min. for Top Overlap. \ \\ FrontFramed \\\ PartialOverlayDoor 2" X4" or _. EquivalentRunners or Solid Shelf DIMENSIONS A CabinetWidth 27r'Min, B CutoutWidth 25r'Min. C CutoutHeight D CutoutDepth E CutoutLocation 27q/21'Min./28q/8" Max, 23-5/8" Min.
Cabinetry Built-In Ovens Recessed installation: Front framed cabinets CabinetWidth NecessaT{! .........To SupportMin. Cutout ...... with inset and doors drawers Front Framed Inset FlushDoor ................ Upper Rail or FabricateFiller PanelSimilar to Drawer Frontor UpperCabinet Doors or Order Additional Drawer Front. ........ 26-7/8" Min. ......... ........ CabinetDepth 24q/2" Min. Frominside Backto Front ............. of CabinetFrameor Side Panel. ".... _i_7::> ........ ....
Cabinetry Built-In Ovens Frameless cabinets ......................... 27............................. Frameless 0 0 ............... Trim Strip or Upper CabinetShelf With FinishedEndslike Cabinet Sides.1/2" Min. Deep for Oven FlangeOverlapandClearance..... ....... 25"Min.............. 25-3/4"Max. ....... ..- CabinetDepth 23 5/8" Min: ........ From InsideBack to Front of CabinetFrameor Side Panel, ExcludingDoors or Drawer Fronts.
Cabinetry Built-In Ovens Single oven installed below rnicro 120Volt, 60 Hz GroundedPower Receptaclelocation Optional onBack Within CabinetOpenTng a wave oven / Allow I3/t6' Overlap for ZMO1090Modeis. Allow I t/4' Overlap for ZEM200WV Microwave Ovent}im Kit Over At Edgesof Cutout Microwave 0p_ning 3/8" /Thick Shelf 1 7/8" ik Opening 27-1/2" Min. -Template 45 1/2" e NOTE:Finishedstructure must support a minimum of 200 Ibs. '4-' --'" ":" :: _--- ,A'" .- 23 5/8" Min. from •" .
Cabinetry Built-In Ovens Single oven installed below a . _--- countertop .._.......... 17-1/2" Oven Junction Box Location SeeCooktop installation instructions ::_: For Cutout .... / / 1-1/T CabinetTop *32" Min. 27-1/2"Min. 28q/8"Max. 23- 5/8" Min. Usetwo 2 x 4's or equivalent runners spaced19" apart (oninside surfaces)centered in opening & flush with top of toekick, * 32" min. from top of cabinet to top of runnersmust be maintained, Monogram ovens can be installed below a countertop.
Cabinetry Modification Built-In Suggestions Ovens Provide oven supports _ ,/ s Cabinet Wails 2"x4"or EquivalentRunners \ : \\\\ i i ii i i i 24" l li i i i i i i i i i i i 1 g" Max. i li l 21'_ 2T' The ovens may be supported 1 by either 27" Min. a solid bottom or 2 x 4 runners. • The support must be level and rigidly flush with the bottom • The entire runners weight edge for single cut out ovens and bottom of 150 lbs. ovens.
Cabinetry Modifications Built-In Determine need for filler panels If the cabinets taller than being the ovens, order because and have finished and should front. for to fill the gaps. available drawer or for larger Drawer fronts are they will match the cabinetry Any cut edges will be seen edges. cabinets usually the opening.
Cabinetry Modification Built-In Cut rail for filler panel Cut the rail out of finished material: • The width cabinet • The height securely plus • The 1/4" • The match rail should oven trim height of both m be enough the rail to the appearance 7/8" to panel, overlap. of the bottom attach be enough Ovens Top Rail width.
Cabinetry Modifications Built-In Cut Suggestions Ovens and secure cleats to filler panel Appearance Panel IlOI Ap ance 1-1j4" II Cle_t Fox"the Cleat top filler panel: • Cut 2 cleats mately 1-1/4" • Cut the cleats against • Secure thick material, approxi- • Cut 2 cleats wide. mately to a length 1/2" at the bottom attach the rail.
Installation Built-In Tools and materials required • Outlet box • Electrical cable--3-conductor or 4-conductorwire--as required by local codes Monogram built-in a separate, properly single delay fuse or circuit • Electrician's pliers flexible power junction Do not use an extension cord with these appliances. box. The which cable conventional convection type ovens at 208 ovens are rated Ovens must length require 120/208 protected breaker.
Installation Built-In Finalize Caution: Do notlift ovenor installation ovendoorbyhandle. %or glass breakage orhandle damagemay occur.Glasssurfaceof doorface Ovens extendsbeyonddoor frameon eachside; be careful not to impactthis exposedglass. Caution: When door is removedandhinge armsare at stop position, do not bumpor try to movehinge arms,Hinges couldsnap back,causingan ir_uryto handsor damageto porcelainsurface. Remove oven door: • Open the door • Grasp each to stop position.
Installation Built-In Secure oven • Slide oven • Drill 3/32" into pilot cabinet oven front frame. Ovens opening. holes through mounting holes in to cabinet 4 screw holes • Secure oven drywall Securely screws cause (2 screw for double in place if cabinet fasten oven the oven screws to do to move single furnished. is particulate to cabinet Faihn'e for ovens, ovens.) with screws provided. holes oi" tip using (Use board).
Installation Built-In Connect electrical (continued) • When connecting to a 3-conductor Connect oven red lead Connect oven black branch to branch lead circuit: circuit to branch red circuit Junction black Box _ _-"""_ Red Connect oven bare to branch copper circuit conductor neutral lead and Wires_X, tt L./7/_ white (white connecting to a 4-conductor Connect oven red Connect oven black lead branch to branch lead .Black _Wires White_._ _ Wires_-_l\ q Cab
NOTE: While performinginstallations described in this book, safety glasses or gogglesshouldbe worn, To obtain specifi€ Monogl_tm infonnaHon product For Monogram local service 1 800 444 1845. Electric. Monogram; General Electric Company Louisville, KY40225 subject Product Therefore, to change improvement Centel _ ill yo_u" area, call is a continuing materials_ without any call GE Answer service at 800. 626.2000--any €oi1Stllllpr i11fOllllati011 mne, day o1 night.
