Installation guide

ManualsBrandsGE Manualswall ovenOfficial GE wall oven

Installation

Instructions

27" Built In Wall Oven

JKP15, JKP18, JKP27, JKP45, JKP56 JKS05,

ZEK937, ZEK957

"If you have questions, call 800-GE-CARES orvisit our website at:

www. GEAppliances.com"

Before you begin

Read these instructions carefully and completely

• IMPORTANT-Save these instructions for

local inspector's use.

• IMPORTANT-Observe all governing

codes and ordinances.

• Note to Installer- Be sure to leave these

instructions with the consumer.

• OWNER- Keep these instructions for future

reference.

• ATTENTION INSTALLER!!

All electric wall ovens must be hard wired

(direct wired) into an approved junction

box. A "plug and receptacle" is NOT permit-

ted on these products

• NOTE- This appliance must be properly

grounded.

Parts Included

Bottom Trim

Single Ovens

4 flat head screws (side trim)

3 pan head screws (bottom trim)

Double Ovens

8 flat head screws (side trim)

3 Pan head screws (bottom trim)

Materials Needed

_¢_ WireNu_ts

Junction

Box

Strain Relief

Clamp for

112" conduit

36" of String

Tools You Will Need

1/8" Drill Bit & Phillips

Electric or Screwdriver

Hand Drill

Pub. No. 31-10473

229c4053P452 1

Summary of content (12 pages)

PAGE 1
Installation Instructions 27" Built In Wall Oven JKP15, JKP18, JKP27, JKP45, JKP56 JKS05, ZEK937, ZEK957 "If you have questions, call 800-GE-CARES orvisit our website at: www. GEAppliances.com" Before you begin • ATTENTION INSTALLER!! All electric wall ovens must be hard wired (direct wired) into an approved junction box. A "plug and receptacle" is NOT permitted on these products • NOTE- This appliance must be properly grounded.
PAGE 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical For Your Safety Requirements This appliance must be supplied with the proper voltage and frequency, and connected to an individual properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating Plate is located on oven side trim.) We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician.
PAGE 3
Installation Instructions Pre-Installation THE FOLLOWING PAGES IS TO BE USED FOR SINGLE AND DOUBLE ill ill OVEN INSTALLATION! JJ_ Door Removal is not a requirement for installation of the product, but is an added convenience. Open the oven door as far as it will go. Remove packaging materials. Check behind hinges, and under false bottom. Remove labels on the outside of the door, plastic on trims and panel, and all tape around oven.
PAGE 4
Installation Instructions 1_ Place the the ovencutout on a opening. table or platform even with (Platform must support 150 Ibs. single, 275 Ibs. double.) Iq_" Remove the bottom trim from the top of the oven. It will be installed at the end of installation. The trim is wrapped separately and taped to the top of the unit.
PAGE 5
Installation Instructions Cutouts for Single Built-In-Oven Cabinet Width 27" Junction Box Location Allow 7/8" for overlap of oven over side 22" Min. above base rail 2" x 4" or equivalent runners Cabinet Width Recommended Cutout Location from Floor 27 Cutout 23 1/2" Depth Cutout Width 25" Min. 25 1/4" Max. 5/8" MIN. 28 1/8" MAX. Cutout / 32 1/2" 20 ,,_ Height 27 5/8" Min. 28 1/8" Max.
PAGE 6
Installation Instructions Cutouts for Double Built-In-Oven Junction Box Location Cabinet Allow 7/8" for overlap of oven over side edges of Width 27" Recommended Cutout Location from Floor 13 1/4" Cutout 23 5/8" Min. above 44"base t Height rail Depth 49 11/16" MIN. 50 1/8" MAX. 2" x4" or equivalent Cutout Wdth 25" Min. 25 1/4" Max. Cutout _>20j. Height 49 11/16" 50 1/8" Max.
PAGE 7
Installation Instructions Cutouts for Single Oven Under Counter Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. \ 240V / 208V Junction Box Location Gas or electric connections for gas cooktop must be located in an adjacent accessible location to the right 25" MIN. 25 1/4" MAX. I 27 5/8" MIN. 28 1/8" MAX. Allow 1" unit overlap all edges ' 22" MIN.
PAGE 8
Installation Instructions IB-1Electrical Connections Turn off the circuit breaker to the oven branch circuit. ATTENTION All electric wall INSTALLER!!! ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. Do not shorten the flexible IR21 I--I conduit.The conduit strain Relief Clamp must be securely attached to the junction box and the flexible conduit must be securely attached to the clamp.
PAGE 9
Installation Instructions Electrial Connections NEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION cont. OR Three-Conductor Branch Circuit Connection • When installing in a new construction, or • When installing oven in a mobile home, or • When local codes do not permit grounding through neutral: When connecting to a 3-conductor circuit, if local codes permit: branch a.
PAGE 10
Installation Instructions Placing the Oven in the Opening Drilling the Pilot Holes _-_ Sliding the Oven Into the Opening. a. Loop (do not tie) a 36" string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. Note: Before drilling the pilot holes make sure the oven is pushed as far back into the opening as it will go and centered. a. I= loop while pushing the oven Pull string into out the on cabinet b.
PAGE 11
Installation Instructions Replacing the Oven Door Preparing for the bottom Trim Installation a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. The oven door is heavy. You may need help lifting the door high enough to slide it into the hinges slots. Do not lift the door by the handle. b. Using the trim as a template mark the center of each slot (three total) where the mounting holes will be drilled. placing one hand on each side.
PAGE 12
Installation Instructions PRE-TEST CHECK LIST Remove all protective film if present, and any stickers. Check that the bottom trim is installed _ properly (see page 10). Chec to sure that allwi in0 is Check to be sure the mounting screws are installed and flush with the side trim, (see page 10). secure and not pinched or in contact with moving parts. _ Operation Checklist [_ emove all items from the inside of the oven. I_ Checkthat conduit is securely connected to the junction box.