GE Monogram ® Installation Instructions Under Cabinet Installation and JX827 Series Microwave Models ZEM£O0 Series Built-In Oven Kit
Before you begin--Read these instructions completely and carefully. IMPORTANT: Save these instructions for local inspector's use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future reference. I_!!,_)t:_:u,,,t_ This appliance must be properly grounded. Supply", page 6.
Design Information Microwave Model ZEM200 available available ff_black, wtlite and Oven Series Electronic microwave ovens stainless steel Dimensions and clearances A- 124/16" (284 mm) A B- 23q3/16" (605 mm) C- 11-3/16" (284 mm) (includes feet) Note: When installedrtrim kit will require wall space26-1/8" W x 16-1/4"H for clearance, _ In-Wall Installation_ 16"q8" Min. / 7" 5"_+1/16"Min.
Installation Preparation Microwave In-wall Tools and materials required: installation • 3/8" thick plywood (min.) • 2" x 4'r lumber Oven 18" Min. Receptacle Inside • Saw Receptacle Outside • Screws and screwdriver or other hardware for construction of plywood base, The opening must be: • 24-7/8"_+ 1/16" wide. • 15" _+1/16" high. • With af)proximately 1-1/4" for oven trim overlap around all edges of opening.
Installation Preparation Microwave With single 0 ven Oven Refer to diagram at right for dimensions when installing above a Monogram single oven. Requirement Within opening of appropriate dimensions: • Install a level base of plywood: - Flush with lower edge of opening. -Entirely covering floor of opening. • 3/8" thick (rain.) plywood must be suf> ported by 2" x 4" or 1" x 2" equivalent runners on all four sides. • Finished floor 100 pounds.
Installation Preparation Microwave Electrical Tools and materials required: • 3-prong grounded electrical receptacle supply • Electricalcable, 2-wire with ground, No 14 minimum, as required Monogram volt, microwave 60 Hz power delay fuse or circuit ovens supply, require protected a 120 by a time breaker. These ovens are supplied with a power cord 40" long for which a properly grounded 3-prong electrical receptacle is required. • 800 watt* oven draws 1300 watts, with a 12.5 amp load.
Installation Preparation Microwave In-wall installation (continued) • When cabinet depth is a critical factor, receptacle should be installed in a side wall at rear of opening: 14-5/8" nlininmm cabinet depth is requ ired. Receptacle installed in side wall, • If receptacle is located behind oven, install receptacle flush with wall to minimize depth: - 16" mininmm depth is required. Receptacle installed behind oven, flush with wall.
Installation MJ('I'O Wa Ve Oven Toolsandmaterials JX8 2 7 installation required: • AccessorykitJX827for in-wallinstallation • 2Phillipsheadscrewdrivers (#1& #2) • Drilland3/32"drill bit • Centerpunch or nail • Pencilandruler JX827 Parts List 1. BasePan Parts Inventory 2. Rear Duct 3. Side Covers (2) 4. Top Trim 5. Bottom Trim 6. Side Trims 7.
Installation Microwave Step 2 Install base pan • Remove tile four top plug buttons fl'om the top of the microwave oven cabinet. • Remove any protective fihn on oven cabinet. • Place the microwave oven centered left to right. Oven Remove4 PlugButtons on the base pan i I i \ I I Step 3 \ Note: Do not tighten screws until all screws are started, install side covers • Install side cover by inserting bottom between oven and base pan.
Installation Microwave RearDuct Screws Step 4 Install rear duct Oven Screw C -%ceScrew Partition in BasePan • Install flange pan. The rear duct between rear possible, by inserting the duct oven should between • Drive the one partition screw base the A. through in the base the of base to the left back flange pan right • Drive bottom back be as far the and the partition on • Locate and use screws into and BasePan side.
Installation Microwave Step 6 Assemble trim Mt frame • Assemble top, bottom and side trims with four screws Screw . . Oveo TopTrim D, as illustrated. / When assembled, top, bottom aird side strips must be flush. %,:.. Note: Bottom trim has a hinge Screw D / _t o Screw / SideTrim Screw / notch and is not interchangable with top trim.
Installation Microwave Under-cabinet m oun ting Tools and materials Oven Buttons required: • Flat-blade screwdriver • Phillips screwdriver • Drill and 1/4" bit • Nail or center punch • Pencil and ruler Embos Cases%Ri ght Side _ • Scissors • Hammer _'-._ •Tape • Safety glasses lYFL • Two brackets (supplied) i -,o, _ LeftSide t l- 1.
Installation Microwave To drill from inside (continued) Oven -Position remaining piece of Template 2 inside cabinet and align hole center line with arrows on Template 1. Cut excess paper from center of Template 2 so it will lie flat. -Distance fl'om right hole center center should measure distance template. Tape remaining place.
Installation Microwave Oven Finalize under-cabinet D°°r_,_nt installation of Cabinet ?_ Bracket 3_l__d A_Top of BottomShelf Sideof Microwave With template secured in place, check again that hole center lines on Template 2 are Remove template and clean drill holes. • Select four bolts--one of each size--fl'om straight, and that distance fi'om right hole center measures distance shown parts package. • Hold each bolt against cabinet fl'ont rail.
Notes Microwave Ovens 15
NOTE: While performinginstallations described in this bOOkr satety glasses or goggles shouldbe worn To obtltin Monogram specific i!?_Ol"lllation conce177i!10o _t!_y product o1"service, c+t!! GE Anst_er ('enter _' consumer infornmtion service time, ck O,o1"night, For Monogram local service 1 800 ddd 1845, NO'I EJ_ctlic stfl_iecl Monogram; General Electric Company Lr.