Installation Instructions 30" Built-In Wall Oven ZET1,ZET2 If you have questions, call 1.800.GE.CARES ge.com Before You Begin Read these instructions carefully and completely. • IMPORTANT-save instructions these for local inspector's • IMPORTANT-observe use. all governing codes and ordinances. • Note to Installer--Be sure to leave these instructions with the consumer.
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS For Your Safety • Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door.
Installation Instructions Pre-lnstallation Checklist ALL INSTALLATION INFORMATION ON THE FOLLOWING PAGES IS TO BE USED FOR SINGLE AND DOUBLE OVEN INSTALLATION! Open oven door and remove literature pack, broiler pan and grid, oven racks, rack supports and a bag with 9 hex nuts. Read Installation Instructions carefully before you begin. m Remove packaging materials. Check behind hinges and under false bottom.
Installation Instructions Pre-lnstallation Checklist cont To Remove the Door (if necessary) Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: Open the oven door as far as it will go. Push both hinge Hinge Unlocked _._L. .,_!!_. locks down toward Position the door frame, Hinge"_/'_ to the unlocked s_ot q_V_ position. This may require a flat blade Hinge screwdriver.
Installation Instructions CutoUtutfOr Single Built-In Oven Width 28 1/2" Min. 28 518" Max. (72.4 to "<-" 72.7 cm) -1L 5"-_L (12.7 cm) I I I I Allow 11/16" --_-_ _(1.75 cm) for overlap of oven over side edges of cutout Opening Between Inside Walls Must Be At Least 28 1/2" Wide 21,, _'_ Junction Box Location 22" (55.9 cm) Height I to Bottom of 27 1/4" Min.I Junction Box 27 6/16" MAX.', '(69.2 to 69.3 cm) I .I-'_ I _'t" I Cabinet Width 30" (76.
Installation Instructions Cutout for Double Built-In Oven Cutout Width Cabinet Width 28 1/2" (72.4 cm) Min. _28 5/8" __ (72.7 cm) Max. (12.7 :m) _ Junction I Box Location / Allow 11/16" --_ (1.8 cm) for overlap of oven over side edges of cutout Allow a minimum of 21" (53.3 cm) for clearance to adjacent corners, drawers, walls, etc. when door is open 30" (76.2 cm) -L s"L Recommended Minimum Cutout Location from Floor 12" (30.6 cm) Cutout Depth 23 1/2" (69.7 cm) Min. Cutout Width 28 1/2" (72.
Installation Instructions Cutout for Single Built-In Oven Under Counter Gas or electric cooktops may be installed over this oven, See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. \ Gas and electrical connections for 30" (76.2 cm) gas cooktop must be located in an adjacent accessible location to the right, For 36" (91.4 cm) gas cooktop, the connections may be made to the left, 240V / 208V Junction Box Location _ 5"_, (12.
Cabinetry r_ Double Oven Cutout for Installation Over a Monogram Warming Drawer 231,2,, (59.7 cm) Single Oven Cutout for Installation Over a Monogram Warming Drawer 231,2(59.7 cm) _Min. Inside--* I.___Min, Inside_* 2"x2"(Scmx 5 cm) or 2" x 4" (Scmxl0 cm) Anti-Tip Block Against Rear Wall, 9" / (22.9 cm) From Floor to Bottom of Block 2" x2" (Scm x 5cm) or 2" x4" (Scm x 10 cm) , Anti-Tip Block Against Rear Wall, 9" (22.9 cm) From Floor to Bottom of Block (69.2 cm) Max. 51 15/16" (131.8 cm) Max, 2" (5.
Cabinetry r_ Single Oven Cutout for Installation Between a Monogram Advantium Oven and a Monogram Warming Drawer Single Oven Cutout for Installation Below a Monogram Advantium 23 1/2" Oven (59.7 cm) Min. ns de_' 23 112" Per Advantium _ Per Advantium Requirem_ g_2" (5.1 cm) M in. ..... iiiiiili: (69.2 cm) 45 114" Max. (114.9 era) Note: Install the oven only with specific models listed on the label located on top of the oven. 45 1/4'ie_ (114.
Installation Instructions Electrical Connections ATTENTION Turn off the circuit breaker or remove fuses to the oven branch circuit. INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below.
Installation Instructions IBI Electrical Connections New Construction and Four-Conductor Branch Circuit Connection cont. This oven is supplied with a 48" (123 cm) long flexible conduit consisting of: 3 insulated conductors (copper) 1 bare ground conductor (copper) • When installing in new construction, or r-BI_ • When installing in a mobile home, or Attach to residence wiring as shown conductors by wiring diagram.
Installation Instructions lcl Securing the Oven in the Opening I_ Sliding the Oven Into the Opening Drilling the Pilot Holes and Mounting the Oven a. Loop (do not tie) a 36" (91 cm) string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered.
Installation Instructions Installing the Oven Rack Supports and Oven Racks Installing the Metal Bottom Trim a. Place the bottom trim between the side trim and against the bottom of the cutout. Oven Rack Supports b. Using two trim screws provided, secure the bottom trim to the bottom edge of the cabinet. Place the rack support with the slotted holes over the rear bolts and the round holes over the front bolts.
Installation Instructions I-D-1 Replacing the Oven Door NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. I-_ Open the oven door as far as it will open. r-_ Push the hinge locks up against the front frame of the oven cavity, to the locked position. i Hinge in Locked Position Lift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle.
Installation Instructions Pre-Test Checklist Remove all protective film, if present, and any stickers. Check that the bottom trim is installed properly (see page 13). Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check to be sure the mounting screws are installed and flush with the side trim (see page 12). NOTE TO ELECTRICIAN: You must unplug the green wire (near where the long flexible conduit exits the unit) when conducting high-potential testing.
Printed in U.S.A.