30” (76.2 cm) Built-In Installation Instructions Wall Oven ZET1, ZET2 If you have questions, call 1.800.GE.CARES or visit our website at: ge.com Before You Begin Read these instructions carefully and completely. e IMPORTANT-—save these instructions for local inspector's use. e IMPORTANT -observe all governing codes and ordinances. ¢« Note to Installer—Be sure to leave these instructions with the consumer. e Note to Consumer—Keep these instructions for future reference.
Installation Instructions MPORTANT SAFETY INSTRUCTIONS For Your Safety e Be sure your oven is installed properly by a qualified installer or service technician. e Make sure the cabinets and wall coverings around the oven can withstand the temperatures (up to 200°F [93.3°C]) generated by the oven. Electrical Requirements (cont.) Rating plate is located on the oven side trim, side front frame or lower front frame.
Installation Instructions iW Pre-Installation Checklist 7 To Remove the Door (if necessary) Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: Remove packaging materials. Check behind hinges and under false bottom. Remove labels on the outside of the door, plastic on trims and panel, all tape around the oven, and any shipping screws securing the oven to the base pad. aN Open the oven door as far as it will go.
Installation Instructions 41] Cutout for Single Built-In Oven zou in ast Cutout Width 73/4" etree 72.7 cml >| Mex) Junetion Box Location (junction box ; may be located in adjacent cabinet) Allow 11/16” Cabinet Width 30" (76.2 cml Recommended Cutout Location from Floor 32 1/2” (82.6 cm) Cutout Depth 23: 1/2” (59.7 cm) Min. se | |] EER] encom a Cutout Width 28 1/2” (72.4 cm) Min. Wide Cutout Height (1.
Installation Instructions A2} Cutout for Double Built-In Oven cia 716 28 1/2" (19.7 cm) Cabinet Width 30” (76.2 cm) 12 eo T Recommended eg (72-4 . Max, cm) Min. be Junction Box Location Allow 11/16" seme TY ook f oven — over sideof edges of \ door is open cee es ee corners, drawers, walls, ete. when Lp Between \ Allow a minimum of 21” (53.3 cm) for clearance to adjacent 12” (30.5 cm) Cutout Depth 23 1/2” (59.7 cm) Min. : Cutout Width : 28 1/2” ” (72.4 cm) Min.
Installation Instructions a3| Cutout for Single Built-In Oven Under Counter Gas or electric cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. 1 240V / 208V Junction 25" Box Location : : (63.5 cm} 7 3/4” si sjocont cabinet Gas and electrical connections for (19.7 cm} Max. in an adjacent accessible location to the right. For 36” (91.4 cm} gas cooktop, the connections may be made to the left.
Cabinetry A4 | Single Oven Cutout for Installation Over a Monogram Warming A5 | Double Oven Cutout for Installation Over a Monogram Warming Dra Drawer |) Anti-Tip Block Against Rear Wall Per Warming | | Anti-Tip Block | Against Rear | Wall Per Warm- Drawer Requirement | 2” (5.1 cm) Min. ing Drawer Requirement 2’ (5.1 cm) H Min. NOTE: Install the Per Warming Drawer Requirement oven only with spe- _ cific models listed on the label located on ~- top of the oven.
Cabinetry A7 | Single Oven Cutout Single Oven Cutout for A8 a Monogram Advantium Installation Between a Monogram Advantium or or Microwave Oven Microwave Oven and a for Installation Below Monogram Warming Drawer ry Per Advantium or Microwave Oven Requirement . _|. ~ Per Advantium or Microwave Oven 2” (5.1 cm) Min. | | 2” (5.1 cm) Min. Requirement _ Note: Install the oven only with specific models listed on the label located on top of a Me | dy |e — the oven.
Installation Instructions B| Electrical Connections ATTENTION INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. DO NOT shorten the flexible conduit. The conduit strain relief clamp must be securely attached to the junction box and the flexible conduit must be securely attached to the clamp.
Installation Instructions B3 New Construction and Four-Conductor Branch Circuit Connection B4 Three-Conductor Branch Circuit Connection When connecting to a three-conductor branch circuit, it local codes permit: e When installing in new construction, or a. Connect the bare oven ground conductor with the crimped neutral (white) lead to the branch circuit neutral (white or gray in color), using a wire nut.
Installation Instructions Securing the Oven in the Opening Ci Sliding the Oven Into C2 the Opening a. Loop (do not tie) a 36” (91 cm) string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. & itt Drilling the Pilot Holes and Mounting the Oven NOTE: Before drilling the pilot holes, make sure the oven is pushed as far back into the opening as it will go and centered. a.
Installation Instructions Installing the Oven Rack Supports and Oven Racks C3 Installing the Oven Rack Supports and Oven C3 Oven Rack Supports Place the rack support with the slotted holes over the rear bolts and the round holes over the front bolts. Using an adjustable wrench, lightly secure with four nuts but do not overtighten or the enamel could be Slide the rack all the way in and push down to lock the front rack locks onto the front chipped. Repeat for the second rack support.
Installation Instructions bp} Replacing the Oven Door le NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. D1 D3 Open the oven door as far as it will open. D4 Push the hinge locks up against the front frame of the oven cavity, to the locked position. Hinge in Lift the oven door by Locked Position placing one hand on each side. The door is heavy, SO you may need help.
Installation | nstructions AW Pre-Test Checklist Vd Vid SK Remove all protective film, if present, and any stickers. Check to be sure that all wiring is secure and not pinched or in contact with moving parts. Check that the bottom trim is installed properly (see page 12). Check to be sure the mounting screws are installed and flush with the side trim (see page 11).
Directives d’installation Four mural encastré modeéles de 30 po (76,2 cm) ZET1, ZET2 Si vous avez des questions, composez le 1.800.561.3344 ou visitez notre site web a: www.electromenagersge.ca Avant de commencer e || est de la responsabilité de l’installateur de procéder 4 une installation appropriée. Un Lisez complétement et attentivement les directives dysfonctionnement du produit qui résulterait d'une installation incorrecte ne serait PAS couvert par la garantie. suivantes.
Directives d’installation CONSIGNES DE SECURITE IMPORTANTES Pour votre sécurité Alimentation (suite) e Assurez-vous que votre four est bien monté par un installateur qualifié ou un technicien de service. latérale du four, sur le devant du cadre latéral ou sur le devant du cadre inférieur.
Directives d’installation W Liste de vérification avant montage G a, Pour enlever la porte (si nécessaire) TOUTES LES DIRECTIVES D'INSTALLATION QUI SUIVENT SONT PREVUES POUR L'INSTALLATION DE FOURS ENCASTRES SIMPLES OU DOUBLES! l est possible d’enlever la porte du four pour faciliter l’installation, bien que cela ne soit pas obligatoire. Pour enlever la porte : Ouvrez la porte jusqu’d son angle maximum.
Directives d’installation Ouverture pour four encastreé simple Al Largeur de ouverture 19,7 cm 72,4 cm (28 1/2 po) min. (7 3/4 po) 72,7 cm (28 5/8 po) max. en max.
Directives d’installation 42} Ouverture pour four encastré double Largeur de ouverture 72,4 cm (28 1/2 po) min. 19,7 cm 72°7 em (28 5/8 pol max. ’ : 76,2 cm (30 po) l'enceinte (7 3/4 po) max Largeur de T Emplacement Distance recommandée entre l’ouverture de la boite et le plancher 30,5 cm (12 po} de jonction erévoir 1,8 em pa {11/16 po} pour le chevauchement du four par- 0 . >| dessus les cotésde - , C ouverture Prévoir un dégagement _ ae | ‘ au i , largeur entre leg ; \
Directives d’installation 43} Ouverture pour four encastre simple installé au dessous d'un comptoir Une table de cuisson électrique ou au gaz peut 6tre installée au-dessus de ce four. Voir les instructions d'installation de la table de cuisson pour connaitre la taille de l’ouverture. Voir l'étiquette sur le dessus du four pour connaitre les modéles de table de cuisson approuveés.
Armoires de cuisine A4 Ouverture pour four encastré simple pour une installation au-dessus d’un tiroir chauffe-plat Ouverture pour four encastré AS double pour une installation audessus d’un tiroir chauffe-plat Monogram Module antibasculement installé contre le mur arriére spécifications pour chaque tiroir chauffe-plat Module antibasculement installé contre le mur arriére spécifications pour chaque tiroir chauffe-plat Dégagement min.
Armoires de cuisine A7 | Ouverture pour four A8 encastré simple pour une installation sous un four Monogram Advantium ou un four des micro-ondes Ouverture pour un four encastré simple installé entre un four Monogram Advantium ou un four des micro-ondes et un tiroir chauffe-plat Monogram 7 Spécificati pécifications pour f four : Spécifications pour four Dég.cmmin. 5,1 (2 :po) Advantium ou four des micro-ondes Advantium ou four des micro-ondes Dég. min.
Directives d’installation Raccordement électrique B AVIS IMPORTANT A L’INSTALLATEUR: B1 Tous les fours muraux encastrés doivent étre raccordés (raccordement direct) dans une boite de jonction approuvée. Une fiche et une prise de B2 courant ne sont PAS autorisées pour brancher ce produit. Mettez le disjoncteur hors circuit ou enlevez les fusibles du circuit terminal du four.
Directives d’installation B3 Nouvelle construction et connexion du circuit de dérivation a quatre conducteurs B4 Connexion 4g un circuit de dérivation a trois conducteurs Lors de la connexion a un circuit de dérivation d trois conducteurs, si les codes locaux le permettent: a. Avec un capuchon de connexion, reliez ¢Lors d'une installation dans une nouvelle construction ou le conducteur dénudé du four, avec le fil neutre (blanc) serti, au circuit de dérivation neutre (de couleur blanche ou grise).
Directives d’installation Fixation du four dans l’ouverture C Ci Mise en place du four dans C2 l’ouverture Percage des trous de guidage et montage du four e a. Faire passer (ne pas nouer) une ficelle de 91 cm (36 po) autour du conduit avant de faire NOTE : Avant de percer les trous de glisser le four en place. On évitera ainsi de guidage, assurez-vous de pousser le four faire tomber le conduit en arriére du four. jusqu’d l’endroit ou il doit aller et de le centrer adéquatement. => a.
Directives d’installation C3 Installation des supports de grille et des grilles du four Installation des supports de grille et des grilles C3 du four (cont.) aN Supports de grille du four = Insérez le support de grille avec les trous ovalisés au-dessus des boulons arriere et les trous ronds au-dessus des boulons avant. Avec une clé ajustable, serrez legerement les quatre écrous sans toutefois trop serrer pour éviter d’endommager |’émail du four. Répétez ces étapes pour le deuxiéme support de grille.
Directives d’installation D| Remise en place de la porte du four 5 D3 Ouvrez la porte du four jusqu’d son angle maximum. D4 tion de verrouillage en poussant vers le NOTE : La porte du four est lourde. Il se peut que vous ayez besoin d’aide pour la soulever assez haut pour la glisser Placez les verrous de la charniére en posi- dans ses charniéres. Ne soulevez pas la porte par la poignée. D1 haut contre le panneau frontal du four.
Directives d’installation IW Liste de vérification avant l’essai iS SRS S'ily a lieu, enlevez la pellicule protectrice et les étiquettes collées sur le four. Vd Vérifiez que tout le cdblage est bien fixé et qu'il n'est pas coincé ou en contact avec des pieces en mouvement. Vérifiez que la garniture inférieure est bien montée (voir la page 12). Vérifiez que les vis de montage sont bien en place et ne dépassent pas la surface de la garniture latérale (voir la page 11).
Instrucciones de instalacion Horno de pared empotrado 30” (76,2 cm) ZET1, ZET2 Preguntas? Visite nuestro sitio en la Web: ge.com Antes de empezar e La instalacién apropiada es responsabilidad del instalador y la falla del producto por una instalacion incorrecta NO esta cubierta por la garantia. Lea estas instrucciones cuidadosa y completamente. e IMPORTANT E-—cuarde estas instrucciones y téngalas disponibles para el inspector local. e NOTA—Este aparato debe estar conectado a tierra adecuadamente.
Instrucciones de instalacion INSTRUCCIONES DE SEGURIDAD IMPORTANTES Para su seguridad Requisitos eléctricos e Cercidrese de que su horno sea instalado adecuadamente por un instalador calificado o por un técnico de servicio. Cerciérese de que los gabinetes y los revestimientos de la pared alrededor del horno puedan soportar las temperaturas (hasta 200°F [93,3°C]} generadas por (cont.
Instrucciones de instalacion VW Lista de control antes de la instalaci6n (; \ {TODA EN LAS DA EN O DOS Para retirar la puerta (si necesario) LA INFORMACION PARA LA INSTALACION PAGINAS SIGUIENTES ES PARA SER USALAINSTALACION DE HORNOS DE UNA UNIDADES! No es necesario retirar la puerta para la instalaci6n del producto, pero hacerlo facilita la instalacion. Para retirar la puerta: S Abra la puerta del horno hasta el maximo. Vid Retire los materiales de embalaje.
Instrucciones de instalacion Corte para los hornos de una unidad Al Ancho del corte 28 1/2” {72,4 cm) Min. 28 5/8” i 73/4" (19,7 cm) Méx. Ubicacién de la caja de conexién (la caja de conexién puede estar ubicada en un gabinete adyacente} (72,7 cm) Max Permita 11/16’ (1,75 cm} para sobrepaso del horno sobre los bordes laterales Abertura entre los del corte paredes teriores del cor debe estar un minimo Ba (69,2 cm) Min.
Instrucciones de instalacion A2 Corte para los hornos de dos unidades Ancho del gabinete Ancho “< permitaiv/iey = (L8cm)pora sobrepaso del horno sobre los bordes laterales “one 73/4" (72,4. cm) Min. 297 cml 285/38" —> (72,7 cm) Max. ff : yp] del corte Ht Abertura “F | ~ entre los paredes un minimo ' de 21” (53,3 cml Coe a de ancho adyacentes cuando las puertas estén abiertas : dela caja Profundidad de conexién del corte 23 1/2" (59,7 cm) Min. Ancho del 28 1/2" (72,4 cm) Min.
Instrucciones de instalacion 43] Corte para los hornos de una unidad- debajo de la superficie del gabinete Las estufas eléctricas 0 de gas se p ueden instalar sobre este horno. Consulte las instrucciones de la estufa para el tamafio del corte. Consulte la etiqueta encima del horno para los modelos de Ubicaci6n de la caja estufas aprobados.
Gabinetes A4 | Corte para los hornos simples, para instalar A5 | Corte para los hornos dobles, para instalar sobre un cajon calentador sobre un cajon calentador Monogra Bloque estable contra la pared rosro pare est ecetee pared trasera la gaveta de 2°15, em) Min, saveta de requisitos calentamiento abd rea ~ - especificos enumerados en la etiqueta que se ubica en la parte superior del horno. Para la gavetade a requisitos a 1” (2,5 cm} Min.
Gabinetes A7 | Corte para los hornos simples, para instalar debajo de un horno Monogram Advantium Corte para los hornos simples, para instalar A8 entre un horno Monogram Advantium o un horno de microondas y un o un horno de microondas cajon calentador Monogram 7 cos Por Advantium o horno de microondas requisitos pt — Por Advantium o horno de microondas requisitos | 2” (5,1 cm) Min. 2” (5,1 cm) Min.
Instrucciones de instalacion Conexiones eléctricas B ATENCION AL INSTALADOR: B1 Todos los hornos eléctricos de pared deben ser cableados directamente en una caja de conexion. Una “enchufe-receptaculo” NO ES permitido en estos productos. B2 NO acorte el conducto flexible. La abrazadera para controlar la presién debe estar firmemente adherida a la caja de conexi6n y el conductor flexible debe estar firmemente adherido a la abrazadera.
Instrucciones de instalacion B3 pa | Conexion de circuito ramal Conexion para nueva construccion y de de tres conductores circuito ramal de cuatro conductores Cuando conecte un circuito ramal de 3 conductores, si los codigos locales lo permiten: * Cuando se instale en una construccién nueva, o a. Conecte el alambre descubierto del horno con el alambre neutro (blanco) del circuito ramal (blanco o gris), usando una tuerca para alambres.
Instrucciones de instalacion Posicion firme del horno en la abertura C Ci Como deslizar el horno en el interior de la abertura Como taladrar los orificios C2 a. Coloque (sin atar) una cuerda de 36” (91 cm) alrededor del conductor antes de piloto y montar el horno deslizar el horno en su lugar. Esto evitard que NOTA: Antes de perforar los orificios piloto, cercidrese de que el horno se el conducto se caiga detrds del horno. empujé hasta el fondo y de que esté centrado. a.
Instrucciones de instalacion C3 | Instalacion de los soportes de C3 | Instalacion de los soportes de las parrillas y de las parrillas del horno (cont. las parrillas y de las parrillas del horno Soportes de las parrillas del horno in fi Coloque el soporte de la parrilla con los orificios ranurados sobre los pernos posteriores y los orificios redondos sobre los pernos frontales.
Instrucciones de instalacion Como instalar la puerta del horno D3 NOTA: La puerta del horno es pesada. Quizds necesite ayuda para levantary deslizar la puerta hacia abajo sobre la s bisagras. No levante la puerta por la empufadura. Empuje los topes de las bisagras contra el marco frontal de la cavidad del horno, hasta alcanzar la posicién de cierre. A D4 Abra la puerta del horno hasta el maximo. Bisagra en la posicién de cierre Levante la puerta del horno colocando una mano en cada lado.
Instrucciones de instalacion W Lista de control antes de la prueba wy Vd SAK Retire cualquier cinta de proteccién y etiqueta que todavia esté presente. Revise para asegurarse de que todos los dlambres estén bien conectados y no aplastados o en contacto con partes moviles. NOTA PARA EL ELECTRICISTA: Al realizar pruebas de alto voltaje, debe desenchufar el cable verde (cerca del sitio de salida del conducto largo y flexible de la unidad). Vuelva a enchufar antes de su funcionamiento.
Notas 43
Printed in U.S.A.