Installation guide

ManualsBrandsGE Manualswall ovenOfficial GE electric oven

Installation Instructions

27"6 30" Electric Built-ln Wall Ovens

Questions? Calt 1.800.GE.CARES(1.800.432.2757) or visit www.GEAppliances.com

In Canada, calt 1.800.561.3344 or visit www.GEApptiances.ca

BEFORE YOU BEGIN

Reed these instructions completely end

cerefully.

" IN PORTANT -- Save these instructions

for local inspector's use.

" IM PORTANT -- Observe all governing

codes and ordinances.

, Note to Installer- Be sure to leave these

instructions with Consumer.

, Note to Consumer- Keep these instructions

for future reference.

, Skill level- Installation of this appliance

requires a qualified installer or electrician.

. Proper installation is the responsibility

of the installer.

, Product failure due to improper installation

is not covered under Warranty.

, Product is for indoor use only.

ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired)into an

approved junction box. A plug and receptacle is NOT permitted on these products.

FOR YOUR SAFETY:

A WAR NING:Before beginning the installation, switch power off at the service panel and

lock the service disconnecting means to prevent power from being switched on accidentally. When the

service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag,

to the service panel.

Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure.

Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit,

stand or hang on the oven door.

Make sure the wall coverings, counters and cabinets around the oven can withstand the heat

(up to 200°F [93.3°C])generated by the oven.

MATERIALS YOU MAY NEED

Junction Box

Wire Nuts

Strain Relief Clamp for 1/2" Conduit

TOOLS YOU MAY NEED

1/8" Drill Bit and Electric or Hand Drill

T20 Screwdriver

PhillipsScrewdriver

Wire Strippers

DESIGN INFORMATION

SINGLEOVENINSTALLATIONS

The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also

be installed below a countertop or below specified cooktops. See the label on top of the oven for approved

models.

DOUBLEOVEN INSTALLATIONS

A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the

oven for approved models.

IMPORTANT:Alwaysreferto individualinstallationinstructionspackedwitheachproductfor specific

requirements.

121 PREPARE THE OPENING

NOTE: Ifthe cabinet does not have a solid bottom, two

braces or runners must be installed to support the weight

of the oven. For single ovens, the runners and braces

must support 220 Ibs (99 kg). For double ovens, the

runners and braces must support 400 Ibs. (181 kg).

NOTE: If marks, blemishes or the cutout opening are

visible above the installed oven, it may be necessary to

add wood shims under the runners and front trim until

the marks or opening are covered.

NOTE: If the cabinet does not have a front frame and

the sides are less than sA"(1.9 cm) thick, shim both sides

equally to establish the cutout width.

2" x 4"(5 cm x 10 cm)

or Equivalent Runners Level

with Bottom of Cutout

and Flush with Sides of Cutout

Suitable

Bracing

to Support.

Ill REMOVE PACKAGING MATERIALS

Failure to remove packaging materials could result in damage to the appliance. Remove all packing

parts from oven, racks and heating elements. Remove protective film and labels on the outer door

and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping

screws securing the oven to the base pad. Open oven door and remove literature pack and oven

racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation

process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from

seperate box and set aside (30" Double Wall Ovens Only).

Summary of content (16 pages)

PAGE 1
Installation Instructions 27"6 30" Electric Built-ln Wall Ovens Questions? DESIGN INFORMATION SINGLEOVEN INSTALLATIONS The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also be installed below a countertop or below specified cooktops. See the label on top of the oven for approved models. Calt 1.800.GE.CARES(1.800.432.2757) or visit www.GEAppliances.com DOUBLEOVEN INSTALLATIONS In Canada, calt 1.800.561.3344 or visit www.GEApptiances.
PAGE 2
CUTOUT FOR SINGLE OVENS IN WALL CABINET 121BICUTOUT NOTE: If the cabinet does not have a front frame and the sides are less than sA" (1.9 cm) thick, shim both sides equally to establish the cutout width. H These ovens are Not approved for stockoble installations. _--.
PAGE 3
CUTOUT NOTE: If the cabinet both sides equally FOR DOUBLE OVENS 12THERMAL OVENS1 does not have a front to establish the cutout frame and the sides are less than . ,, ' ', ! '._ r .......... CUTOUT hick, shim i=ldth. _AL,I _ "1 , sA" (1.9 cm) Junction _ Box Location (junction / boxmay /beloca/ed --in adjacent l I I I I B NOTE: Additional clearances above the Warming Drawer """"""'_ models OVER A WARMING listed on the label located DRAWER on top of the over].
PAGE 4
_-I PEDESTAL RAIL INSTALLATION (30" DOUBLE OVENS ONLY) A. Place one pedestal rail on each cabinet runner or centered on opposite side of solid cabinet bottom flush with side of cabinet opening, Locate each rail so that front of rail is behind front cabinet opening, B.
PAGE 5
[_ DOOR REMOVAL (RECOMMENDED) r_ NOTE: Door removal is not a requirement for installation of the product but is an added convenience. To remove the door: A. Open the oven door as far as it will go. ELECTRICAL REQUIREMENTS (CONT.) This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse. See the rating plate located on the oven frame to determine the rating of the product.
PAGE 6
I""Z'-I [_] MAKE ELECTRICAL CONNECTIONS 8L_8_J FOUR-CONDUCTOR A WA RNING:Sw,tch power offatthe serv,ce pane, and ,ock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Place oven on table or platform even with the cutout opening. For a single oven, the platform must support 220 Ibs.
PAGE 7
r_ MOUNT THE OVEN _ must be used. Failure to do so could result in the oven falling out of the cabinet, causing serious injury. NOTE: Before drilling the pilot holes, make sure the oven is pushed as for buck into the opening as it will go and is centered. NOTE: If the cabinet is particle board, you must use #8 × 3A"particle board screws. These may be purchased at any hardware store.
PAGE 8
_OVEN RACK GUIDE INSTALLATION (IF APPLICABLE) _ A. Locate included oven rack guide mouting hardware. REPLACING THE OVEN DOOR B. Place oven rack guides on cavity wall studs with L bracket towards back of cavity as shown. NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. C. Install guides using the 8 provided mounting nuts. A. Lift the oven door by grasping each side. B.
PAGE 9
Instrucciones de instalaci6n Hornos depared el ctricos empotrados de27"y30" _Preguntas? Llame ai 1.800.GE.CARES(1.800.432.2737) o visite GEAppiiances.com En Canad& Itame al 1.800.561.3344 o visite www.GEAppliances.ca. , ANTES DE COMENZAR Lea estas instrucciones par completo y con detenimiento. , ° IMPORTANTE - Guardeestasinstrucciones para el usa de inspectoreslocales. ° IMPORTANT -- Cumplacon todos los c6digosy ordenanzasvigentes.
PAGE 10
ABERTURAPARAHORNOSUNICOSENUN GABIENTEDEPARED ABERTURA PARA HORNOS I]NICOS = BAJOELMOSTRADOR DEENCIMERA NOTA: Si el gabk]ete no cuenta con un armaz6n frontal y los lados son menores a un grosor de 3/4" (1,9cm), coloque cuRos uniformemente sobre ambos Iodos poro estoblecer a] ancho de Io oberturo. Estos homos no est6n aprobados para instolociones apilables.
PAGE 11
ABERTURA PARA HORNOS DOBLES (2 HORNOS TERMICOS) NOTA: Si el gabinete no cuenta con un armaz6n frontaJ y los lados son menores a un grosor de 3/4" (1,9 cm), coloque cu_as uniformemente sobre ambos lados _ara establecer al ancho de la abertura. Ubicaci6n de Jacaja de conexiones (la caja de conexiones -_== B--_ t Z[ZJ111) I ABERTURA PARA INSTALACION CALENTADOR SOBRE UN CAJ6N NOTA: InstaJe el homo s61o con los modelos especfficos ]istados en la etiqueta ubicada en la parte superior del homo.
PAGE 12
r_ IN STALACION DEL RIEL CON PEDESTAL (30" HORNOS DOBLES UNICAMENTE) A. Coloque un riel con pedestal en cada rodadura del gabinete o centrado en el lado opuesto de la parte inferior del gabinete s61ido nivelado con el lateral de la abertura del gabinete. Ubique cada riel de modo que la parte frontal de los mismos se encuentre detr6s del lado frontal de la abertura del gabinete. B. Realice agujeros de prueba y adjunte los deles a la rodadura o a la parte inferior del gabinete con el equipo provisto.
PAGE 13
REMOCION DE LA PUERTA (recomendada) NOTA: La remod6n de la puerta no es un requedmiento comodidad adicional. _-j de Jainstalaci6n del producto, pero es una Para quitar ]a puerta: REQUiSiTOS ELi_CTRiCOS (CONT.) Este aparato debe recibir el voltaje y frecuencia adecuados, y debe conectarse a un circuito derivado individual con adecuada conexi6n a tierra, protegido par un interruptor de circuitos o fusible.
PAGE 14
REALICE LAS CONEXIONES A DVE RTE N C [A: ELI_CTRICAS Desconecte la energiadelpaneldeservicio y bloqueelosmedios de descone×i6n para evitar el accionamiento de la energia de manera accidental. Cuando los medios de descone×i6n de servicio no pueden bloquearse, coloque sobre el panel de servicio un dispositivo de advertencia bien visible, como una etiqueta. Coloque el homo sobre una mesa o plataforma en forma nivelada con la abertura. Para un homo 0nico, la plataforma debe soportar 220 Ibs.
PAGE 15
INSTALE EL HORNO _ Deben utilizarse tornillos de montaje. Si no Io hace, el homo puede caer del gabinete, Io que provocar[a una lesi6n grave. NOTA: Antes de perforar los orificios piloto, asegOrese de que el homo se encuentre en la posid6n final de la abertura y centrado. NOTA: Si el gabinete es de placa de partTculas, deben utilizarse tornillos #8 × s_,, para dicho material. Estos pueden adquirirse en cualquier ferreteria.
PAGE 16
GUIA DE INSTALACI6N CORRESPONDE) DE LA ESTANTERIA DEL HORNO (Sl _C6MO VOLVER A COLOCAR LA PUERTA DEL HORNO NOTA: La puerta del horno es pesada. Puede necesitar ayuda para levantar la puerta Io sufidente como para deslizafla dentro de las ranuras de la bisagra. No levante la puerta de la manija. A. Ubique el equipo de montaje de la gufa del homo induida. B. Posidone el conducto de modo tal que se apoye detr6s de la unidad en un cfrculo natural cuando el homo sea instalado. C.