Installation I str cti n Professional Outdoor Grills and Cooktop Tables de cuisson et barbecues de plein air professionnels Instructions La section d'installation ffan_aise commence _ la page 23 Parrillas y estuf@ profesionales para el @ire libre Instrucciones de instalaci6n La secci6n en espa_ol empieza en la p(_gina 45 C I31-107021 11-08JR JS
Installation Instructions BEFORE YOU BEGIN - WARNING: Read these instructions • For outdoor use only. Use this outdoor grill or cooktop only in the manner intended by the manufacturer. completely and carefully. • IMPORTANT- save these instructions for local inspector's • use. IMPORTANT-Observe allgoverning codes and ordinances. • Note to InstallerBe sure to leave these instructions with the Consumer. • Note to Consumer - Keep these instructions with your Owner's Manual for future reference.
Installation Instructions FOR OUTDOOR USE ONLY INSECT WARNING! IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THIS MANUAL THOROUGHLY BEFORE INSTALLATION, USE OR SERVICING THIS EQUIPMENT. Spiders and insects can nest in the burners of this and ang other grill and cause the gas to flow from the front of the burner.
Design Information CONTENTS Tools Required ...................................................................... 12 Materials Required .............................................................. 12 Parts Provided ...................................................................... 12 Design Information Models Available ...................................................................... a Product Dimensions and Clearances ...................... 5-7 Accessories .....................................
Design Information PRODUCT DIMENSIONS AND CLEARANCES 54" Built-In Side View, All Built-ln Grill Models 12" Min. to Combustibles_ 4" Min. Clearancefor Lid -1 to Non-Combustibles i A 1¢1/4" from Bottomof iiSupportFlange fl I I I I U ........................ :_ ............. _....... 42" Built-In _25-1/2" CountertopDepth 27" to Front of ControlPanel i i ' 12" Min. to Combustibles.... 4" Min. Clearancefor Lid ._ i 28-1/2"to Frontof Bullnose \,.........
Design Information PRODUCT DIMENSIONS 54" Cart with AND CLEARANCES Side Burners 12" Min. to Combustibles 4" Min. Clearancefor Lid to Non-Combustibles -i_ 51" 15-1/2"(bothsides) _ 53-7/8" 54" Cart 12" Min. to Combustibles 4" Min. Clearancefor Lid ,. to Non-Combustibles 15-1/2"(bothsides)-- _- ..
Design Information PRODUCT DIMENSIONS AND CLEARANCES 42" Cart 12" Min. to Combustibles 4" Min. Clearancefor Lid --_ to Non-Combustibles I_' 15-1/2"(bothsides_ 51 " S //41-7/8" 30" Cart 12" Min. to Combustibles 4" Min.
Design Information ACCESSORIES ZX18DS, 18" 2-Drawer Storage ZX27AD, 27" Access Doors ZX18TC, 18" Trash Bin ACCESSORY PRODUCT DIMENSIONS 22-5/8" ;_ 18-1/8"_ 2G" 20" 27" •........................................
Installation Preparation ADVANCE PLANNING CHOOSING THE LOCATION Built-In Monogram Outdoor Grills (Ire designed for easg installation into a masonrg, non-combustible enclosure. The grill drops into he opening and hangs from its side flanges. These outdoor grills (Ire designed for outdoor use only. Do not Iocote the grill in a building, garage or other enclosed or semi-enclosed area. • Ensure that fresh air ventilation • A deck is not required for support from the bottom. is adequate.
Installation Preparation ELECTRICAL SUPPLY REQUIREMENTS GAS SUPPLY REQUIREMENTS A 120-volt, 60Hz, 1S-amp power supplg is required. An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle at the rear and below the cutout. Electrical must be located within reach of the 6-ft. power cord. These grills are factorg-set gas operation.
Installation Preparation OUTDOOR GRILL, COOKTOP AND ACCESSORY CUTOUT DIMENSIONS 12" Min. Separation Between Cutouts 28-3/4"for30"Models 40-3/4"for42"Models 52-3/4"for 54"Models 11-7/8" and ElectricalLocations •24-1/2" 24-1/2" ZGU122 AccessDoors ZX27AD 24" 2-Drawer Storage ZX18DS Grill Cutout 36" Min. TrashBin ZX18TC 10-7/8" 18-1/4" 24/4" min.
Installation Preparation PARTS PROVIDED TOOLS REgUIRED Drill and AppropriateBits SaberSaw Grill Cover AdjustableWrench MeasuringTape RotisserieMotor and Connector 1/4" Driveror Wrench Carpenter'sSquare RotisserieSpit Forks DripPan Flat-BladeScrewdriver (3/32" blade) SafetyGlasses 9V Battery(installed on somemodels) Phillips#2 Screwdriver Level Bracketwith Transformerand BatteryCompartment(only on built-in models) SmokerBox (onsomemodels) Pliers ApplianceDolly ,/ CuttingBoard ion some mo
Installation Preparation REMOVE PACKAGING FROM CART MODELS 1. Cut the banding. Use o box cutter or utilitg knife to score and cut the carton along the base (or remove the staples with a staple remover or a screwdriver). 2. Lift the carton straight t 6. Open the lid. Cut plastic ties and bands. up and off of the grill. jCut withthe tin banding snips. L Score and cut. 3. Remove all outside packing materials. 7.
Installation Preparation REMOVE PACKAGING FROM CART MODELS Icont.) 10. Roll the grill into operating shelf on the right side. 8. Position the blade of the dollg next to the right side of the grill. Tilt the grill back and awag to allow blade to slip under the wheels. NOTE: The wheels must rest on the blade of the appliance dollg. position. Reinstall the Secure the appliance -dolly belt around the grill above or below the controls to avoid damage to the knobs. 9.
Installation Preparation REMOVE PACKAGING FROM BUILT-IN MODELS 1. Cut the banding. Use o box cutter or utilitg knife to score and cut the carton along the base (or remove the staples with a staple remover or a screwdriver). 2. Lift the carton straight up and off of the grill. 6. Close the lid. Cut the plastic tie holding the wires against the left side. Let the batterg and transformer wires hang loose along the back side. I Cutthe banding with tin snips. -- Cuttie on the rearvertical support.
installation LP TANK TIE-DOWN {for built-in island installations} Outdoor cooking applicances require an integral means of limiting the movement of the LP gas cylinder. For built-in appliances which require the use of a remote LP gas supply cylinder (island applications), a retaining device must be created. Lateral movement shall not exceed !" (25./4 mm) at the retention means.
Installation LP GAS GRILL CONNECTIONS Single Gas Cooktop or Grill Instructions TO A GRILL OR COOKTOP {cont.} Outdoor Cooktop: Install the cooktop with a separate tank using the same method. Order WB21X10156 Regulator hose assembly for the 20-lb. tank connection. Connection LPHoseand Regulator To connect 20-lb. LP tank: • Attach the regular hose assembly to the brass elbow. Do not use threading compound. • Insert the coupler sleeve on the regulator over the tank inlet; turn clockwise to tighten.
installation -&WARNING: Natural Gas Leak Test Points TEST FOR LEAKS A complete gos tightness check must be performed the instollation site. at -&CAUTION: To prevent fire or explosion hozard, DO NOT use or permit sources of ignition in the orea while performing a leok test. Perform leak test outdoors only. Never perform o leok test with fire or flame. DO NOT SMOKE WHILE PERFORMING THE LEAK TEST.
Installation Instructions INSTALL BRACKET WITH TRANSFORMER lBuilt-ln • Mount the bracket to the back wall of the enclosure with 4 screws (not supplied). Models Onlg) NOTE:All connectors are polarized to connect correctlg. Join transformer connectors. • Slide the battery compartment from the top, straight down, engaging the side slots. Join batterg connectors. Route the power cord through electrical outlet. Battery/Fuse _l.
I stall ti I str cti t Z×27AD ACCESS DOORS 24-1/S" i -_ DoubleAccess Doors _ i 18-1/4" 7/8" t ° Cut the opening to the dimensions shown. Reinforce the inside of the opening using ot least 1" wide moteriul surround to accept the frame-mounting screws. . Ploce the flume into the opening ond secure with screws (provided)on oil sides us shown. , Hung the doors on the hinges us shown.
I stall ti I str cti ZX18DS STORAGE DRAWER IMPORTANT: The supplied rear support bracket adjusts from 4-1/8" to 6-7/8". When using the supplied bracket, cut the opening at least 4-1/8" above the floor. If the opening is closer to the floor of the enclosure, use another means of support for the back of the drawer. 18-9/16" The rear support must be capable of supporting 50 Ibs., plus load. o Cut the opening to the dimensions shown.
I stall ti I str cti ZX18TC TRASH BIN . Cut the opening to the dimensions shown. Reinforce the inside of the opening using at least 1" wide material surround to accept the frame-mounting screws. Mounting Screws(10) NOTE: If you are installing another accessory into the same enclosure, measure and cut the openings to accommodate the bottom overlaps and align them evenlg across the bottom. . Separate the mounting frame from the trash bin door.