Installation Instructions 36" Built-in All-Refrigerators and All-Freezers 31-49062-2 224D2601 PO02 01-15 GE monogram,com
Safety information BEFOREYOU BEGIN Read these instructions completely and carefully, . IMPORTANT- Save these instructions forlocal inspector's nances, use, Observe all governing .
CONSIGNES DE SECURITE ACe symbole represente une alerte de s6curite, Ce symbole vous avise de dangers possibles pouvant causer la mort, des blessures ou autres, Tousles messages de s6curite seront prec6d6s du symbole d'alerte de s6curite ainsi que des mots << DANGER >>,<>ou <>,Ces messages sont les suivants : _ Signale une situation qui presente un danger imminent sures graves, voire la mort, et qui, si elle n'est pas evitee, entrainera Signale une situation qui pre
Contents Safety Planning Guide The Installation Space Dimensions and Clearances Customization Basics 3/4" Overlay Panel Dimensions - Flush 1/4" Framed Panel Dimensions - Standard 3/4" Overlay Panel Dimensions - Standard Side Panels ZUG2 and ZUGF2 Grille Panel Dimensions 130 ° Door Swing 90 ° Door Swing Installation Instructions Tools, Hardware, Materials Grounding the Unit Parts Identification Step 1, Remove Packaging Step 2, Install Water Line 2,3 5 5-7 8 9 10 10 11 11 12 13 14 14 15 16 16 Step Step Step
Design Guide THE INSTALLATION DIMENSIONS AND CLEARANCES SPACE 35-I/2" Finished Width 25-3/8"FramedModels 25-3/4"StainlessSteelModels CaseDepth Shipping height, The product can be adjusted to fit into a cutout that is 84-1/2" max, height, *84" From Note that the top case FI00rt0 TopFrame trim at the front is 1/2" 35" CaseWidth Wall View 75-1/2" From Floorto Bottom of ElectricalArea J upper cabinetry or sofhigher will overlap fit, Use and leveling legs and wheels for a maximum 1" height adjustment,
Desi n Guide CLEARANCES FOR FLUSH INSTALLATION ONLY 15" 4" Min.to Wall Iqin.
Desi n Guide CLEARANCES FOR STANDARD INSTALLATION AND STAINLESS MODELS ONLY 4"Min.to Wall _25"_ Min. to 130° Swing Door 2" Wall 0 DoorSwing z I I',1 I,_ 36-3/4" , 1300 .... Installed , vlL These units are equipped with a 3-position door stop. The factory set 115 ° door swing can be adjusted to 90 ° or 130 ° if clearance to adjacent cabinets or walls is restricted. Order WX14X99 door stop for precise settings between 90 ° and 130 °, When L I_Z I ; .....
Desi n Guide CUSTOMIZATION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Professional Style Stainless Steel Models Stainless steel wrapped refrigerators have beveled edges and professional-style handles, These models are shipped ready for installation, Stainless Steel Wrapped Models Stainless Steel wrapped models have wrapped doors and grille panel, beveled edges, and tubular stainless steel handles that coordinate with other Monogram appliances, These models are shipped ready for in
Desi n Guide 3/4" OVERLAY PANEL DIMENSIONS CUSTOM HANDLE DESIGN GUIDE (Flush Installation (Flush Installation Only) For custom Only) handle installation, counterbore holes in For a more custom appearance, overlay panels may be installed to give a flush appearance with surrounding cabinets, The overlay panel must be 3/4" thick, Panel rear of decorative panels may not exceed 1/4" depth to ensure 1/2" material thickness remains for handle attaches to included appliance door, support, NOTE: The cou
Desi n Guide 1/4" FRAMED PANEL DIMENSIONS (Standard Installation Only) m, If you choose to install framed panels, they must be cut to the dimensions shown, The panels will slide into the frame on the door and grille, Door bs/!6, ' LTrim Reveal iiiiiiiiiiiiiiiiiiiii!iiii!iiii! ..............
Design Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the unit will be exposed, The 1/4" side panels will slip into the side case trim, Secure the panels to the unit with stickon hook and loop fastener strips, Order the side panels from the cabinet manufacturer, The ZUG2 unified grille panel kit provides for the installation of a framed or overlay grille panel, A Grille Panel , Cut a notch in the top front corner as shown to allow clearance for corner keys
Desi n Guide Frameless Refrigerator or Freezer 23-7/8" From Rearof Ink Case Trim 3/4" 1/2" 1/4" Cabinets: The case trim overlaps cabinets at the top and sides, Therefore, frameless cabinets may require filler strips to prevent interference with cabinet door swing, The opening must allow for filler strips, 1-3/4" 1-1/2" 1-1/4" 2-1/4" CabinetFront , 3/4" Overlay Panel "",,,, (NominalSize) Door Top View 130 ° DOOR SWING (Standard Scale 1:1 Installation Only) 12
Desi n Guide Frameless Refrigerator or Freezer Cabinets: The case trim overlaps cabinets at the top and sides, Therefore, frameless cabinets CaseTrim may require filler strips to prevent interference with cabinet door swing, 23-7/8" The opening must allow FromRear of for filler strips, Unit Cabinet Front / / / / / / u i .............. t--. 1/4" i u ...... L 1/2" ....................... i 3/4" u ,.... -.... •.... . ...........
Installation Instructions TOOLS AND MATERIALS REQUIRED GROUNDING THE UNIT , Tin snips to cut banding ----_}_ , #2 Phillips screwdriver , Stepladder , Drill and 1/2", 3/16" bits , Bucket Electrical Failure to follow these instructions fire, or electrical shock, Shock Hazard.
Installation Instruction PARTS IDENTIFICATION: Panel Bracket, Top Right Trim, Handle Side Visor Panel Bracket, Bottom Left Panel Bracket, Bottom Right Trim, Handle Side Cover Panel Bracket, Top Left h............. t Panel Bracket, Top Trim, Freezer Hinge Side Panel Bracket, Bottom Door Bracket (4); Installed on door Door Panel Template . TOPI_ HI.GESAREONT, ELEF Trim, Case, RH Side BO_O,,_ IFHINGES ARE O.
Installation Instructions ISTEP 1 1REMOVE PACKAGING _Tip Over Custom HandleTrim Hazard. ii Product is much heavier at the top than at the bottom - be careful when moving, When using a hand truck, handle from side only, 1_V't_ Y Remove Tie-D0wns Risque de basculement J Le produit est beaucoup plus Iourd en haut qu'en bas, II faut 6tre prudent Iors des deplacements, Si un diable est utilise, il faut soulever le refrigerateur sur le cote seulement, J .
Installation Instructions ISTEP 41 INSTALL CASE TRIM STEP 5 INSTALL ANTI-TIP (cont.
Installation Instructions I STEP 5] INSTALL ANTI-TIP BRACKET (Standard/Stainless only) (cont.) Center . Hold the ends of the straps in one hand and slide the plastic cap along the straps until the flange of the cap is flush with the wall, Wall Bracket I J/ / I' •I _F : ] . Gently pull back at the ends of the plastic straps to make the channel rest flush behind the wall, Installation .... -oJ .o-Io_ I i / Line OnWall JJ° : ........... i .............. ij_ .... .
Installation Instructions STEP 5 INSTALL ANTI-TIP BRACKET (Standard/Stainless Installation only) (cont.) Remove Grilles for Access to Anti-Tip Power Cord Locate the power cord inside the left cavity, If it has not been adjusted so the plug is easily accessible, do so now, Locking Hooks "L" Bolt Fresh Food Unit \ * Open the access door, * Remove the 4 screws from the grille, * Pull the bottom of the grille forward, down and out to remove, q, ) \ \ \ PowerCordLocation Move Unit into Final Positio
Installation Instructions STEP 6 LEVEL UNIT ISTEP 7 ISECUREAPPLIANCE TO CABINETRY All models have 4-point leveling, The front is supported by leveling legs; the rear is supported by adjustable wheels, Both are accessible from the front of the unit, Flush Installation .
Installation Instructions STEP 81 SECURE UNIT TO WALL Standard and Stainless Installation Only . The "L" rods can be found in the upper left and right corners of the unit in the access compartment, Look through the access compartment to make sure the rods line up with the anti-tip bracket, . There are 2 washers and a hair pin cotter per rod, Remove the washers and hair pin cotter from the end of the rod, ._._<,_.::_ ,, . ............. , . L RodP0mtlngDown Engaged inBracket _ r lX .
Installation Instructions [STEP 9 ADJUST DOOR SWING STEP 10 REMOVE DOOR TRIM - FLUSH INSTALLATIONONLY NOTE: This appliance has a 3-position door stop, When space does not allow the door to swing open fully to 115 °, you may change the door swing to a 90 ° opening, A 130 ° door swing is available for standard installation only, Skip this step if door opening is satisfactory for your installation situation.
Installation Instructions [STEP 111 LAYOUT DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY Decorative wood panels must be cut to a thickness of 3/4". The dimensions of each panel can be determined by referring to the specs provided with appliance. Panels must be predrilled to prevent accidental splitting or cracking of wood when attaching to door brackets in the next step.
Installation Instructions [STEP 12 ATTACH BRACKETS TO PANELS - FLUSH INSTALLATION Locate wood panel brackets and wood panel screws in Flush Inset Hardware Kit located inside the appliance drawer. These brackets will install to rear of decorative wood panels to provide attachment to door brackets already installed on doors.
Installation Instructions STEP 13 HANG DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLY Panel with attached brackets will mate with steel brackets already attached to top, sides, and bottom of the door. Each bracket attached to the door will have two machined screws recessed inside the door to provide anchoring points for wood panel brackets to install onto the doors.
Installation Instructions [STEP 14 LAYOUT DECORATIVE GRILLE PANEL - FLUSH INSTALLATION ONLY Grille area will also have decorative attached to installed steel bracket.
Installation Instructions [STEP 16 ADJUST DECORATIVE PANELS - FLUSH INSTALLATION The panel can be adjusted approximately 1/8" both left and right, up and down, as well as outward from the door to provide planar appearance with cabinets.
Installation Instructions [STEP 16 ADJUST DECORATIVE PANELS - FLUSH INSTALLATION ONLY STEP 17i REPLACE TRIM- FLUSH INSTALLATION ONLY (Cont) , 1, Replace trim and 6 screws on hinge side of the door, 2, Replace handle visor trim and four screws on the handle side of the door, Make the final vertical adjustment of the door panel, Using the set screw at the top of the door, turn clockwise until the desired gap between the grille panel bottom and top panel of the door appears 3, Replace trim cover and fou
Installation Instructions ISTEP 191START ICEMAKER (FREEZERMODELS ONLY) STEP 18 CONNECT WATER SUPPLY (FREEZERMODELS ONLY) I Icemaker / /, "\ House _Water Supplg Freezer Water Supplg _.
Notes 30
Notes 31
NOTE: While book, safety For Monogram performing installations described in this glasses or goggles should be worn. ® local service in your area, call 1,800,444 ,I 845, NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE 31-49062-2 224D2601 P002 01-15 Printed GE in the United States Appliances Appliance Park Louisville,KY40225 GEAppfiances.
