Installation guide

ManualsBrandsGE ManualsFreestanding FreezerOfficial GE freezer - x series

Printed in the United States 224D3383P001 31-49005 03-13 GE

Installation Instructions

Single Door Drain Pan Kit (WR74X10355)

MODELS: ZIF*360NX* AND ZIR*360NX*

Questions? Call 1-800-GE-CARES (1-800-432-7237)

PARTS PROVIDED:

Single Door Drain Pan Kit (WR74X10355)

Drain Pan Assembly

Baffle Template

Evaporator Cover Assembly

#10 Self-tapping Screw

10 Watt Heater

Harness

TOOLS REQUIRED:

#2 Phillips Screwdriver with

6” Extension for Screwdriver and

1/4 Head-head attachment

RTV 102

Flat-head Screwdriver

Scraper

PPE REQUIRED:

Safety Goggles

Safety Gloves

Padding/Support for knees

IMPORTANT SAFETY NOTICE:

This kit is to be installed by a qualified service technician only. Any attempt to repair a major

appliance may result in personal injury and property damage. Failure to follow these installation

instructions can result in personal injury or property damage.

USE THESE INSTRUCTIONS FOR MONOGRAM SINGLE-DOOR UNITS ONLY

Summary of content (18 pages)

PAGE 1
USE THESE INSTRUCTIONS FOR MONOGRAM SINGLE-DOOR UNITS ONLY Installation Instructions Single Door Drain Pan Kit (WR74X10355) MODELS: ZIF*360NX* AND ZIR*360NX* Questions? Call 1-800-GE-CARES (1-800-432-7237) PARTS PROVIDED: Single Door Drain Pan Kit (WR74X10355) Drain Pan Assembly Baffle Template Evaporator Cover Assembly #10 Self-tapping Screw 10 Watt Heater Harness TOOLS REQUIRED: #2 Phillips Screwdriver with 6” Extension for Screwdriver and 1/4 Head-head attachment RTV 102 Flat-head Screwdriver Scrap
PAGE 2
PROCEDURE: SNACK PAN SHELF FZ SNACK PAN ASM COVER IM ASM SHOWCASE LID PAN ASM COVER ICE BUCKET ASM VEG PAN BASKET ASMS Picture 1 1. Unplug the unit. 2. Remove SNACK PAN SHELF FZ {WR17X12679}. (See PICTURE 1) 3. Pull out, disengage clips, and pull off of the slide rail to remove COVER IM ASM {WR32X10804}. Left Side Clip is pushed upward. Right Side Clip is pushed downward. 4. Pull out and upward to remove SNACK PAN ASM {WR32X10078}. (See Picture 1) 5.
PAGE 3
SUPPORT SNACK PAN ASM 6. Pull out to remove two STRIP SD FZ VEG PAN {WR02X13223}. STRIP SD FZ VEG PAN 7. Remove screw and WASHER SHOWCASE PIVOT {WR01X10046} (these will be put back) from side nearest unit wall to allow SHOWCASE LID PAN ASM {WR32X10720} to be removed from bushing.
PAGE 4
Screw to be removed Washer to be removed 8. Push inwards at sides in back and dislodge from bushing (if bushing falls, put it back on the wall of the cabinet) to remove Left {WR32X10119} and Right SHOWCASE LID PAN ASM {WR32X10720}. (See PICTURE 1) 9. Pull out and upward to remove COVER ICE BUCKET ASM {WR32X10728}. (See PICTURE 1) 10. Pull out and upward to remove VEG PAN WIRE ASM {WR21X10209}. 11.
PAGE 5
12. Pull out and upward to remove four VEG PAN BASKET ASM {WR32X10121}. 13. Pull out, disengage clips (Refer to Picture under Note 2), and pull off of the slide rail to remove four SUPPORT VEG BASKET ASM {WR72X10200}. (See PICTURE 1) SUPPORT VEG BASKET ASM 14. Remove two 8-32 X 5/8" PH SS TCS SCREWS {WR01X10484} holding the ice maker. (Freezer only) 15. Unplug the icemaker. (Freezer only) NOTE: Flathead screwdriver may be needed to disengage clips.
PAGE 6
16. Remove icemaker assembly and set it aside. (Freezer only) 17. Remove eight #10-16 X 1/2 TAPPING SCREWS holding the center divider assembly. (These will be reused) 18. Pull out to remove DIVIDER CENTER ASM {WR72X10320}. Screws to be removed Center Divider Assembly 19. Use screw driver to remove seven SELF DRILL TRIM P SCREWS holding the evaporator cover. Save fasteners for reuse. 20. Remove EVAP COVER ASM {WR74X10355} and discard.
PAGE 7
Screws to be removed 21. Unplug 9-pin connector of HARNESS HEATERS TOD {WR09X10180} from back wall of the unit. NOTE: Flathead screwdriver may be needed to disengage clips. 22. Unplug Defrost heater {WR51X10113} from the HARNESS HEATERS TOD {WR09X10180}. 23. Unclip thermodisc and remove HARNESS HEATERS TOD {WR09X10180} (Harness can be discarded). Unclip thermodisc and remove. Unplug these harness connections 24. Use driver to remove four SELF DRILL TRIM P SCREWS holding the catch evaporator trough.
PAGE 8
25. Remove CATCH EVAPORATOR TROUGH {WR17X12711}. (This will be put back later) Screws to be removed Catch Evaporator Trough 26. Use driver to remove four #10X1\2 PH SMS SCREWS {WD02X0295} holding the Evaporator in place. Screws to be removed 27. Pull Evaporator forward slightly to work behind it. 28. Use driver to remove four TRIM (SELF TAPPING) SCREWS holding the drain baffle in place.
PAGE 9
Drain Baffle Screws to be removed 29. Use scraper to separate the gasket of the drain baffle from the back wall of the unit. 30. Remove DRAIN BAFFLE {WR17X12683}. NOTE: Remove any pieces of the gasket that tear and stick to the back wall of the unit 31. Remove DRAIN PAN {WR17X11016}. 32. Use the TRIM (SELF TAPPING) SCREWS to screw the baffle template in place using the four lower holes.
PAGE 10
NOTE: Wait until all four screws have been started before tightening them. 33. Use hex-head attachment to drive the four #10 Screws in the 4 upper holes. NOTE: Wait until all four screws have been started before tightening them. 34. Remove the TRIM (SELF TAPPING) SCREWS from the baffle template. 35. Discard the baffle template. Location of new holes to be drilled with Self-tapping screws. TRIM (SELF TAPPING) SCREWS 36.
PAGE 11
37. Peel right side of tape on new drain pan to just past the farthest hole on the right side. 38. Insert spout of new drain pan into drain of unit. 39. CAUTION: Ensure the spout on drainpan is not impacted and loosened during installation. Do not force. 40. Use the driver to start a TRIM (SELF TAPPING) SCREW {WR01X10188} through the farthest right hole of the drain pan and into the farthest right hole that was just drilled into the back wall of the unit. NOTE: Do not tighten fully.
PAGE 12
41. Peel the tape further until it is past the next hole on the drain pan and screw into place. NOTE: Do not tighten fully (Repeat for the remaining screw holes.) NOTE: Do not bend EVAPORATOR FINS. 42. Wait until all four screws have been started before tightening them. 43. Apply a small amount of RTV along the top edge of the drain pan where it meets the back wall of the cabinet. CAUTION: Do not get RTV on the EVAPORATOR FINS to prevent improper operation.
PAGE 13
CAUTION: DO NOT GET RTV ON THE DEFROST HEATER to prevent malfunction. RTV to be applied 44. Screw the Evaporator back into place with the four #10X1\2 PH SMS SCREWS {WD02X0295}. 45. Clip thermodisc on new HARNESS HEATERS TOD into place. 46. Connect the 9-pin connector on new HARNESS HEATERS TOD. 47. Plug Defrost heater and drain pan heater into new HARNESS HEATERS TOD. NOTE: Drain pan heater wires should come over the side of the pan.
PAGE 14
Clip thermodisc into place Plug in Defrost heater Plug in 9-pin connector Plug in Drain Pan Heater Picture 2 48. Screw the CATCH EVAP ORATOR TROUGH {WR17X12711} back into place with the four SELF DRILL TRIM P SCREWS. NOTE: Slide under new evaporator trough instead of over).
PAGE 15
SLIDES UNDERNEATH THE DRAIN PAN CAUTION: DO NOT BEND OR CHANGE THE GEOMETRY OF THE DRAIN PAN to prevent malfunction. 49. Take new evaporator cover and screw into place with seven SELF DRILL TRIM P SCREWS. 50. Replace DIVIDER CENTER ASM {WR72X10320}. 51. Screw back into place using eight #10-16 X 1/2 TAPPING SCREWS. 52. Replace icemaker assembly. (Freezer only) 53. Screw back into place using two 8-32 X 5/8" PH SS TCS SCREWS {WR01X10484}. (Freezer only) 54. Plug in icemaker.
PAGE 16
Turn switch from the “OFF” to “ON” position. 55. Replace drawers and baskets. 56. Plug in unit.
PAGE 17
WR74X10355 31-49005
PAGE 18
Universal Keywords: Div46 Src363 GE General Electric Mechtech Document Specific Keywords: Instruction Sheet Date: 101116 Document Name: 31-49005 Subject: GE Monogram Refrigerator/Freezer Single Door Drain Pan Kit Instructions Models: ZIR360NXALH ZIR360NXARH ZIRS360NXALH ZIRS360NXARH ZIRP360NXALH ZIRP360NXARH ZIF360NXALH ZIF360NXARH ZIFS360NXALH ZIFS360NXARH ZIFP360NXALH ZIFP360NXARH REF0413