Installation Instructions 27" and 30" Warming Drawers Models: ZKD910 ZTD910
Safety Information BEFORE YOU BEGIN AWARNING Read these instructions This appliance must be properly grounded. See "Grounding the Appliance." completely "IMPORTANT- and carefully. save these instructions for local inspector's For Monogram local service in your area, 1.800.444.1845. use. "IMPORTANT-Observe codes and ordinances. all governing , Note to InstallerBe sure to leave these instructions with the Consumer.
Design Information CONTENTS Design Information Models Available ...................................................................... 3 Installation Accessories ................................................................................. 3 Step 2, Install Warming Product Dimensions ............................................................... 4 Custom Panel Accessory Kit Installation ...........10, 11 Grounding the Appliance Professional Style Panel Accessory Kit Installation ...............
Design Information PRODUCT DIMENSIONS AND CLEARANCES A ',I :i Drawer Open II ° _ /" 23-1/4" _ II / ..4_, kll / / (_1, i / 10-1/2" 9" ,nclBuding__ _ d_C Handle Dimensions A B C 22" 26" 30" 23-i/4" 27-i/2 22"26" 26-3/4 '_ ZTD910 ZTD910 w/ZXD30P ZKD910 '_ 30" ADVANCE PLANNING • Thedrawer may be installed belowa countertop,a cooktop,a singleor doubleoven and side by side using 2 drawers. • Thewarming drawer can be installed belowapproved cooktops.Allow 2" min.
Design Information GROUNDING THE APPLIANCE Please read carefully. FORPERSONALSAFETYTHISAPPLIANCEMUSTBE PROPERLY GROUNDED, Do not use an extension cord or adapter plug with this appliance. Follow National electrical codes or prevailing local codes and ordinances. Recessed Receptacle This warming drawer must be supplied with 120V, 60Hz, and connected to an individual, properly grounded branch circuit, and protected by a 15 or 20 amp circuit breaker or time delay fuse. 7" Max.
Installation Preparation TOOLS REQUIRED MATERIALS REQUIRED (provided) /4Wood Screws Hand Saw Safety Glasses MATERIALS REQUIRED (not provided) Drill and 1/16" Bit Measuring Tape Level Phillips Screwdriver 2x2 or 2x4 2x2 or 2x4 Wood Block for Anti-Tip Security Lumber for Runners _ Adhesive or other hardware for installing runners or shelf to support warmer drawer Runners must be level, rigidly mounted and capable of supporting 150 pounds. REMOVE PACKAGING , Place carton on a flat surface.
Installation Preparation INSTALLATION OPTIONS Installation a Single Below Oven Installation a Double Below Oven 23-1/2" Hin. lnside t 2x2 or 2×4 Anti-Tip Block Against Rear Wall, 9" From Floor to Bottom of Block 2×2 or 2×4 Anti-Tip Block Against Rear Wall, 9" From Floor to Bottom of Block jo- Allow 5/8" 2" IVlin. Overlap on / All Sides 2" IV]in. 1" Min. Above Toekick or Adjust to Oven Installation Height B i" Min.
Installation Preparation INSTALLATION BELOW A COUNTERTOP Electrical Electrical Outlet 42" Max. From Right Side Outlet 1-1/2" Cabinet Top Flush With Side of Electrical Outlet &B" Max, From Left Side Cabinet Install 2×4 or 2×2 Anti-Tip Block Against Rear Cabinet Wall 9" From Floor to Bottom of Block 7" Max. 7" 25" '\ o o_.-o: Install a Solid Barrier Below a Cooktop See Note r' Hin.* 9-i/4" 36" Countertop Height Solid Barrier Dimensions A 23-1/2" Hin.
Installation PROVIDE CABINET SUPPORT 2"x4" or Equivalent Runners , i 23-i/2" // \\ , i i i i i i i i I I i i i i i i I , 2"x4" or Equivalent Runners / -- I - i \ i < Ii i i i i i i i i i i i i i i i i i i i i i i i i i i i 23-!12" i i I % / I i i / 27 30" IMPORTANT:When installed below a single or double oven, check to be sure • The support must be level and rigidly mounted, flush with the bottom edge of the cutout.
WARMING DRAWER CUSTOM PANEL ACCESSORY KIT Installation Instructions ZXD27B AND ZXD30B For installation of 27" and 30" wide warming drawer custom panel and custom handle. BEFORE YOU BEGIN STEP i PREPARE DRAWER FOR PANEL INSTALLATION Read these instructions completely and carefully. , IMPORTANT- Save these instructions for . Open the drawer fully. . Turn the warming drawer off. local inspector's use. Observe all governing codes and ordinances. .
Installation [ STEP 4 I SECURE CUSTOM PANEL TO METAL MOUNTING PANEL [ STEP 6 I INSTALL LAMP JEWEL Turn the assembly appearance side up . Use plastic to wood adhesive to secure the lamp jewel to the front of the wood panel On the side with the bulge, (see illustration) apply a small bead of adhesive around the outside edge Place the jewel into the drilled hole. . Lay the custom panel, appearance side down on a clean surface .
Installation Instructions BEFORE YOU PROFESSIONAL STYLE PANEL ACCESSORY KIT ZXD30P BEGIN STEP2 Read these instructions completely and carefully. , IMPORTANT- save these instructions local inspector's and ordinances. use. Observe all governing for REMOVE ORIGINAL DRAWER FRONT , Remove the three screws from the bottom of the codes drawer edge. , Remove the four screws on the inside of the , Note to Installer - Be sure to leavethese instructions withthe Consumer. drawer at the top.
Notes 13
Notes 14
Notes 15
NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. GE Appliances & Lighting Appliances General Electric Company Louisville, KY/40225 GEAppliances.
