Installation Instr ct ® 36" Glass Canopg Chimneg Vent Hood ZV900 Monogram° 49-80328-3 ]
Safety Information AIA#^OklIMr_ JllVV_I_'_I_I_I II_I_I: TO REDUCE THE RISKOF FIRE,ELECTRICALSHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: BEFORE YOU BEGIN Read these instructions completely and carefully. " IMPORTANT- Sove theseinstructions for A. Use thisunitonlginthemonner intendedbg the monufocturer. Ifgou hove ong questions, contoctthe monufocturer. Iocol inspector's use. "IMPORTANTond ordinonces. Observeollgoverningcodes B.
Design Information CONTENTS Design Information Installation--Recirculating Product Dimensions and Clearances .................................................... 3 Ductwork, Wiring Locations .................................................................... 15 Installation Options ........................................................................................ 3 Step !, install Framing for Hood Support ......................................... 15 Step 2, install Mounting Bracket ..................
Installation Preparation ADVANCE PLANNING • Determine the exact location of the vent hood. • Use metal ductwork only. These hoods must use 8" round duct. Plan the route for venting exhaust to the outdoors. • Use the shortest and straightest duct route possible.For satisfactory performance, duct run should not exceed 100 ft. equivalent length for any duct configurations. • Install a wall cap with damper or roof cap at the exterior opening. Order the wall or roof cap and any transition needed in advance.
Installation Preparation DUCT FITTINGS Duct Piece Use this chart to compute maximum permissible lengths for duct runs to outdoors. Dimensions Equivalent Length* Round, straight 1 ft. (per foot length) 3-!/4" x !2" straight ! ft. (per foot length) guantitg Used 90 ° elbow NOTE: Do not exceed maximum permissible equivalent lengths! !7ft. 45 ° elbow !0 ft. Maximum duct length: 100 foot for range hoods.
Installation Preparation % TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED} Gloves Tape measure Knife _, Spirit level Wire cutter/stripper _, Wire nuts Electric drill with 5/16" and 3/8" bits Spirit level Measuring tape Phillips and flat blade screwdrivers Hammer _, Pliers Pliers Safetg glasses _, Duct tape Tape to mount template Gloves to protect against sharp edges !20V 60Hz.
Installation Preparation DETERMINE INSTALLATION HEIGHT , Telescopic duct covers are provided to conceal the ductwork running to the ceiling. , This hood can be installed for recirculating operation. No kits required. NOTE: Me installation height from the cooking surface to the outer glass portion of the hood. 24" Min. 30" Max.
Installation Preparation CHECK INSTALLATION Locate the hardware m HARDWARE accessorg box packed with the hood and check contents.
Installation Instructions INSTALLATION-VENTEDTO THE OUTSIDE DUCTWORK, WIRING LOCATIONS Determine the exact location of the vent hood. , Locate the template packed with the literature. - Measure 36" from the floor to the top of the cooking surface. Add hood installation height determined on page 7. Mark that location. - Use a level to draw a straight pencil line on the wall.
Installation instructions INSTALLATION-VENTEDTO THE OUTSIDE i2] INSTALL MOUNTING BRACKET INSTALL DUCT BRACKET This vent hood must be secured to the horizontal support or wall studs. The duct bracket should be installed against the back wall and flush with the ceiling. This bracket will hold the duct cover in place at the top. . With the template taped in place, use a punch to mark mounting bracket screw locations. Secure the bracket to the wolh .
Installation instructions INSTALLATION-VENTEDTO THE OUTSIDE PREPARE THE HOOD , Place the hood on a padded surface. , Carefullg lag the hood on its back. , Position the motor housing at the back of the hood. Electrical connectors should face the front, with rear mounting hooks at the back. , Fasten the hood to the motor housing from the bottom, using 6 screws. Front side , Slip the bottom flange of the motor housing into the side slots at the top rear opening. )} \ / Rear \ mounting hooks Rear v
Installation Instructions INSTALLATION-VENTEDTO THE OUTSIDE _-_ MOUNT THE HOOD [-_ WARNING: 2people are required position the hood onto the mounting AVERTISSEIENT to lift and bracket. , Install ductwork, making connections direction of airflow as illustrated. in the , Push duct over the exhaust outlet and damper. : , Secure joints in ductwork If faut deux personnes pour lever et mettre en place la hotte sur le support de montage.
Installation Instructions INSTALLATION-VENTEDTO THE OUTSIDE [_ CONNECT ELECTRICAL Verify that power is turned off at the source. , Removejunction left side. WARNING: ,f house wiring is not 2-wire with a ground wire, a ground must be provided by the installer. When house wiring is aluminum, be sure to use U.L approved anti-oxidant compound and aluminum-to-copper connectors.
Installation instructions INSTALLATION-VENTEDTO THE OUTSIDE i-9-1 INSTALL DUCT COVERS . Place the decorative INSTALL FILTERS duct IMPORTANT: Check to be sure that the main ON/ OFF switch next to the motor is in the ON position. .__ covers on top of the hood. Plounting_ NOTE: The inside (upper) screws duct piece has holes on one end. The holes are intended for use when the hood is installed for recirculating purposes.
Installation Instructions INSTALLATI O N--R ECIRCULATI NG DUCTWORK, WIRING LOCATIONS INSTALL FRAMING FOR HOOD SUPPORT , Determine the exact location of the vent hood. , Locate the template packed with the literature. IMPORTANT: Froming mustbecapable of , Measure 36_
Installation Instructions INSTALLATI O N--R ECIRCULATI NG INSTALL MOUNTING BRACKET [-_ This vent hood must be secured to the horizontal support or wall studs. INSTALL DUCT BRACKET The duct bracket should be installed against the back wall and flush with the ceiling. This bracket will hold the duct cover in place at the top. , With the template taped in place, use a punch to mark mounting bracket screw locations.
Installation Instructions INSTALLATI O N--R ECIRCULATI NG PREPARE THE HOOD MOUNT THE HOOD WARNING: , Place the hood on a padded surface. 2 people are required to lift and position the hood onto the mounting bracket. , Position the motor housing at the back of the hood. Electrical connectors should face the front, with rear mounting hooks at the back. AVERTISSEMENT : , Slip the bottom flange of the motor housing into the side slots at the top rear opening.
Installation Instructions INSTALLATI O N--R ECIRCULATI NG | SIZE AND CUT DUCT PIECE _-1 CONNECT ELECTRICAL , Hold upper air deflector with duct connector against the ceiling. Verify that power is turned off at the source. WARNING: _f house wiring is not 2-wire with a ground wire, a ground must be provided bg the installer. When house wiring is aluminum, be sure to use U.L approved anti-oxidant compound and aluminum-to-copper connectors.
Installation Instructions INSTALLATI O N--R ECIRCULATI NG [-_ INSTALL DUCT COVERS , Place the decorative duct covers on top of the hood. NOTE: The inside piece has holes on one end intended for use when the hood is installed for recirculating purposes. Be sure the vented end is at the top; the vent holes will be visible in this installation. INSTALL FILTERS Haunting IMPORTANT: Check to be sure that the main ON/ OFF switch next to the motor is in the ON position.
NOTE: While performing installations described in this book, safetg glasses or goggles should be worn. For Monogram _ local service in your area, call 1.800.44¢.18¢5. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice. Monogram: [49-80328-3 02-13 1 GE GE Appliances General Louisville, Printed in Mexico & Lighting Appliances Electric Company KY 40225 monogram.
