PETOL™ Flange Lifter FLA1000 Data Book Warning Improper use of flange lifters may result in injury or death. Do Not Exceed Rated Load of 1000 Pounds. Follow safe practices listed in Data Book. GEARENCHTM P.O. Box 192 4450 South Highway 6 Clifton, Texas 76634 Phone: (254) 675-8651 Fax: (254) 675-6100 © 2014 by GEARENCH. All rights reserved.
Table of Contents PETOL™ Flange Lifter Description ..................................................................................... 1 Warranty ................................................................................................................................. 2 Safe Practices and Procedures ............................................................................................... 5 Responsibility .........................................................................................
PETOL™ Flange Lifter Description The FLA1000 PETOL™ Flange Lifter hangs from a shackle or a hook, which is attached to a lifting mechanism such as a crane or a hoist. The lifting mechanism moves the Flange Lifter up and down to install and remove ANSI B16.5, ANSI B16.47 Series A, and ANSI B16.47 Series B blind and weld neck flanges. Load ratings for the lifting mechanism and shackle or hook components should be greater than or equal to the rated load of the Flange Lifter.
Warranty What Is Covered GEARENCH™ tools are expressly warranted to you, the purchaser, to be free of defects in material and workmanship. How Long Coverage Lasts This express warranty lasts for the lifetime of the GEARENCH tool. Warranty coverage ends when the tool becomes unusable for reasons other than defects in workmanship or material. How Can You Get Warranty Service To obtain the benefit of this warranty, contact a GEARENCH sales representative in Clifton, Texas. GEARENCH · 4450 South Highway 6 · P.
claim or injury to the fullest extent allowed by law, and disclaims and denies any liability for such personal injury. Please be advised that some states do not allow the exclusion or limitation of liability for personal injuries, so the above limitation or exclusion may not apply to you, or the individual claiming injury. No Other Express Warranty Applies This GEARENCH LIMITED WARRANTY is the sole and exclusive warranty, express or implied for GEARENCH products.
any obligations expressed in any customer purchase order or document that are contrary to the terms and limitations of this warranty. Severability If any term or limitation contained in this limited warranty is deemed unenforceable by law, then the term shall be severed from the remaining portions of the limited warranty which shall remain enforceable. All communications to GEARENCH regarding the use of the tool and any aspect of the sale of the tool of this limited warranty should be addressed to GEARENCH.
Safe Practices and Procedures Responsibility It is the responsibility of the employer to train the employee in the proper selection and use of flange lifters, and to ensure that they are selected and used in that manner. A part of the job instruction program should therefore be detailed training in the proper use of flange lifters. "Employers are responsible for the safe condition of tools and equipment used by employees, including tools and equipment which may be furnished by employees.
Hazard Being struck by flanges or flange bolts should they slip Possible Solution Ensure that workers are instructed in proper flange lifter procedure Being struck by flanges or flange bolts not securely connected Inspect the tools before use Inspect and maintain flange lifters Periodic Maintenance and Inspection Schedule Daily 1. Visually inspect flange lifter for signs of corrosion or damaged components. 2. Inspect for any visual evidence of external cracks.
Assembly Drawing ITEM 1 2 3 4 5 QTY 2 1 1 14 2 PART NUMBER FLP1000 FLL112 HP044 FLS112 HXP016 7 DESCRIPTION LIFTING PLATE LIFTING LINK PIN SPACER LYNCH PIN
Operation As shown in Figure 1 on the next page, set the width of the Flange Lifter by removing the Lynch Pins and placing the Lifting Plates between the proper number of Spacers to allow for the space between the Lifting Plates to be just wider than the thickness of the flange. There should be just enough space between the Lifting Plates and the flange to keep the flange level and balanced in its working position. Keep the Lifting Link centered between the Lifting Plates, and use every Spacer.
9
Replacement Parts Repairs should only be made by GEARENCH™ or a repair facility authorized by GEARENCH. Responsibility of Distributors GEARENCH DISTRIBUTORS ARE RESPONSIBLE FOR FORWARDING THIS DATA BOOK AND OTHER GEARENCH PRODUCT INFORMATION RELATING TO THE INDIVIDUAL PRODUCT, THROUGH THE CHANNELS OF DISTRIBUTION, DOWN TO AND INCLUDING THE INDIVIDUAL USING THE PRODUCT.
Certificates 11
