Operation Manual

ManualsBrandsGeba Tronic ManualsVehicleTCS - Cody 1-2

Instructions for Assembly and Use

TCS-Cody 1/2

Electronic encoder-type lock for garage door drives

The TCS-Cody is a modern and safe alternative to traditional key switches. The

TCS-Cody can safely be used after two simple programming steps (master code

and pass code). For opening or closing of the door only a four- or five-digit nume-

ral code (pass code) has to be entered, which has been previously programmed via

the master code by an authorized person.

After correct input of the pass code and pushing the key button the drive is trigge-

red by the corresponding potential free relay contact.

The high flexibility of the encoder is achieved by extensive programmability of the

individual operating functions. All sections required for operation are, however, pre-

programmed and thus immediately ready for use.

Technical Data:

24 V series 230 V series

Supply voltage 12 - 24 V AC / DC 230 V AC 50 Hz

Output 2x NO, NC relay contacts, 2x NO,NC relay contacts,

isolated, 8 A 250 V isolated, 8 A 250 V

Connections 2.5 mm

max., 2.5 mm

max.,

Ambient- -20 ˚C to +60 ˚C -20 ˚C to +60 ˚C

temperature

Adaptation of the TCS-Cody 1/2 to special requirements:

The TCS-Cody 1/2 is provided with a series of flexible time settings which allow the adapta-

tion to special cases of application. For programming these special operating modes please

ask for our flow chart for the TCS-Cody series, if required!

geba GmbH is released of its obligations regarding guarantee and product liability if - without

prior permission - the unit has been modified, or if the installation is unproper or not in

accordance with our instruction manual.

The installer has to take care that the EMC-regulations are respected.

The most important characteristics of the TCS-Cody are:

Simple operation, programming and assembly.

Water-protected enclosure.

➢ A maximum of safety:

➢ The electronic decoder is separately installed in the

protected area

➢ Up to 50 different pass codes can be stored

Up to 100 million different coding possibilities

Variable lock-out function

Nearly unlimited data security, even with power failure

➢ Special TIPTOMATIC-function for garage doors: After input of the pass

code the door can be stopped within the TIPTOMATIC time adjusted by

actuation of any key, and be closed or opened by repeated actuation

of any key.

➢ Two potential-free relay outputs

➢ High switching capacity for direct control of appliances

industial controls

Summary of content (4 pages)

PAGE 1
Adaptation of the TCS-Cody 1/2 to special requirements: ® ® industial controls industial controls The TCS-Cody 1/2 is provided with a series of flexible time settings which allow the adaptation to special cases of application.
PAGE 2
® industial controls Dear customer, ® industial controls Program 2 Clearing of a pass code The Cody which you have purchased is one of our highest quality technical products. We have taken the greatest care in its manufacture to ensure that this microprocessor controlled encoder reaches you in faultless condition. However in the unusual event of suspected equipment failure please return the appliance together with the enclosed warranty document to your dealer or direct to our factory.
PAGE 3
® ® industial controls industial controls Description of the appliance Program 2 Input / Clearing of a pass code Input 8-digit master code The TCS-Cody consists of a decoder and a keyboard. The units are connected by a simple double-wire cable without a special plug. Programming of the TCS-Cody is possible with the keyboard and the master code.
PAGE 4
® ® industial controls industial controls Assembly Instructions Programming Instructions Assembly of the CODY keyboard: 1. By slightly pushing the two latches at the right and left side of the keyboard from behind to the edge, remove the small frame from the keyboard. 2. Now you see two fixingholes (diam. = 4 mm) at the front of the keyboard. By means of these you can fix the keyboard onto the wall. 3. Connect the keyboard to the logic unit by means of a twin-cable (up to 5 m long).