Specification Sheet

2
Geberit
2100 S. Clearwater Drive
Des Plaines, IL 60018
USA
P 800-566-2100
F 847-803-5454
→ geberit.us
© 2016 Geberit. Product specifications subject to change without notice.
Optional Parts for
Geberit Duofix Carrier 111.335.00.5
Required Accessories for 3.50”-7.00” (9-18 cm) Finished Wall
Thickness
Description Model No.
HDPE Connector set for extended installation 152.438.46.1
and mounting hardware (bowl installation kit),
with socket for Ø3.50” (Ø90 mm) push fit piping
and Ø55 supply inlet; Matte Chrome cover caps
Extension set for actuator plates for Sigma 240.938.00.1
Concealed Tanks 2x6 and 2x4, and Kappa
and Omega Concealed Tanks
Mud guard protection housing for Sigma 241.826.00.1
Concealed Tanks 2x6 and 2x4, Plastic
Mounting rod M12 x 10” long. —
Not supplied.
Bidet Seat Accessory for Carrier Frames
Water supply hose for bidet seat for 249.801.00.1
Sigma Concealed Tanks 2x6 and 2x4 and
Kappa and Omega Concealed Tanks. For
adding bidet seat to an installed carrier.
Waste Fittings
Description Model No.
HDPE straight connector with socket for 366.887.16.1
Ø3.50” (Ø90 mm) push fit piping and
Ø3.50” (Ø90 mm) outlet x 12” (31 cm) long
HDPE connector with offset for LH horizontal 366.913.16.1
drain connections (as viewed from sitting
position), 1 x 90° bend with socket for
Ø3.50” (Ø90 mm) push fit piping, with 45º
offset and Ø3.50” (Ø90 mm) outlet
for 5.5” (13.97 cm) minimum walls only
HDPE connector with offset for RH horizontal 366.914.16.1
drain connections (as viewed from sitting
position), 1 x 90° bend with socket for
Ø3.50” (Ø90 mm) push fit piping, with 45º
offset and Ø3.50” (Ø90 mm) outlet
for 5.5” (13.97 cm) minimum walls only
Cast iron outlet bend; 1 x 90° bend with 367.071.18.1
socket for Ø3.50” (Ø90 mm) push fit piping
and 3” CIP outlet
HDPE “Back-to-back” connector for 367.485.16.1
horizontal drain connections; 2 x 90° bends
with sockets for Ø3.50” (Ø90 mm) push fit
piping, with 45º offset and expansion to
Ø4.375” (Ø110 mm) outlet for
10.75” (27.31 cm) minimum walls only.
HDPE “Back-to-back” connector for vertical 367.923.16.1
drain connections; 2 x 90° bends with
sockets for Ø3.50” (Ø90 mm) push fit piping
and expansion to Ø4.375” (Ø110 mm) outlet
for 10.75” (27.31 cm) minimum walls only.
Bowl Connection Sets and Accessories
Description Model No.
Connector set with mounting hardware (bowl 152.404.11.1
installation kit), HDPE; Alpine White cover caps
Acoustic insulation set for wall-hung toilets 156.050.00.1
and bidets
Cover caps with leveling washer, Plastic, 217.713.11.1
Alpine White
HDPE connection set with 1” (2.5 cm) offset 405.116.00.1
and mounting hardware (bowl installation kit);
with socket for Ø3.50” (Ø90 mm) push fit
piping and Ø55 supply inlet; Matte Chrome
cover caps
GNA7051 04/16