CL2L Telephone ringer amplifier with flasher and door bell Indicateur d’appel téléphonique avec flash et sonnette Telefonklingelverstärker mit Blitz und Türklingel English Page 2 Français Page 15 Deutsch Page 28
CAUTION: The switch for Ringer ALARM selection must never be set during ringing/ flashing mode but always when CL2 is silent mode ( No incoming call ringing). ATTENTION: Le commutateur de configuration du mode Alarme ne doit jamais être changé lorsque le CL2 envoie sa sonnerie ( ou flash lumineux ) mais uniquement durant le mode repos. WARNUNG: Bitte die Taste für die Auswahl des Klingeltons niemals während des Läutens bzw. Blitz-Signals betätigen, sondern nur im Ruhe-Modus ( kein eingehender Anruf ).
DESCRIPTION 1. DESCRIPTION The CL2 will alert you to both doorbell and telephone. It has adjustable volume and different tone settings for doorbell and telephone.
INSTALLATION 2. INSTALLATION 230V Double plug Screw wall mount AC/DC d t Door Bell Button Door Bell Wall socket Telephone Option : Special cable to link two CL2s Option : Shaker (ref.: SHAKCL_BLK only) 1 - Connect the CL2 line cord in CL2 “Line IN”. 2 - Connect your Telephone in the double plug of the line cord. 3 - Connect the double plug in the Telephone wall socket. 4 - If necessary connect the required shaker (SHAKCL_BLK only) to the shaker plug input.
INSTALLATION (*) Classified "hazardous voltage" according to EN60950 standard. Electrical connection: The apparatus is designed to operate from a 230V 50Hz supply only. (Classified as 'hazardous voltage" according to EN60950 standard). The apparatus does not incorporate an integral power on/off switch. To disconnect the power, either switch off supply at the mains power socket or unplug the AC adaptor. When installing the apparatus, ensure that the mains power socket is readily accessible.
BELL PUSH WALL MOUNTING 3.1. BELL PUSH – WALL MOUNTING The wire free bell push is mounted by the front door. It has a range of 20-60 metres depending on the structure of the building (see note). Test the system before mounting on the wall – plug in the CL2 and press the bell push button to check that the CL2 rings. To mount the bell push, open the access cover in the middle of the bell push with a needle or small screwdriver.
BELL PUSH WALL MOUNTING WALL MOUNTING TEMPLATES To wall mount the bell push or the CL2, use these templates to mark the screw hole centres. We recommend the use of a spirit level to ensure the holes are level.
BELL PUSH CHANGE THE BATTERY 3.2. CHANGE THE BATTERY The door bell is supplied with a 23A 12V battery. The CL2 is supplied ready to use, it is not necessary to open the bell push when you first install the CL2. To replace the battery, open the access cover and unscrew the door bell from the wall, unscrew the three screws located on the base and open the box to get access to the battery compartment. Replace the battery, replace back and remount.
SETTINGS CL2 4.1.
SETTINGS CL2 RING TONE CONTROL The three position switch allows you to set the tone of the CL2 ringer when the telephone rings. DOOR BELL TONE CONTROL This three position switch allows you to set a different tone when the door bell rings. OPTIONAL ACCESSORIES: Extra bell push – to cover a second door, such as a kitchen door. Shaker – the Geemarc shaker unit (CLA2) can be tucked under your pillow or at the side of your chair to vibrate when the doorbell or telephone rings.
SETTINGS PAIRING 4.2. The Pairing Procedure ( Note : Factory default setting : paired. ) 1. Press and hold the (Pairing/Test) button for 2 seconds to enter pairing mode, at the same time, the unit makes a beep sound. 2. The 1st LED lights, to pair the BELL PUSH, press and (Pairing/Test) button and then Bell hold the push button at the same time, the 1st LED flashes, after paired, the 1st LED lights and stop flashing, beeps to confirm. 3.
SETTINGS PAIRING 4.3. Un- Register The Pairing 1. Press and hold the Pairing/Test button for 5 seconds to enter un-register mode, 3 LED light together. 2. If user wants to un-register the 1st BELL PUSH, press the Pairing/Test button within 2 seconds, the 1st LED will be flashing (the other 2 LED light), means user is now un-registering the 1st BELL PUSH, press the Pairing/Test button until the 1st LED goes off, beeps to confirm. The 1st remote is now un-registered. 3.
TROUBLESHOOTING 5. TROUBLESHOOTING If the CL2 system doesn't work correctly, please carry out the following checks before calling the helpline: ● If the phone rings but the CL2 does not ring: Check the connection between the phone socket and the CL2. ● If the door bell does not ring: 1. Check that the CL2 is plugged into the mains and switched on. 2. Unscrew the bell push and check the battery is correctly fitted. 3. Try fitting a new battery. 4.
GUARANTEE 6. GUARANTEE From the moment your Geemarc product is purchased, Geemarc guarantee it for the period of one year. During this time, all repairs or replacements (at our discretion) are free of charge. Should you experience a problem then contact our helpline or visit our website at www.geemarc.com. The guarantee does not cover accidents, negligence or breakages to any parts. The product must not be tampered with or taken apart by anyone who is not an authorised Geemarc representative.
RECYCLING DIRECTIVES 7. RECYCLING DIRECTIVES Recycling directives: The WEEE (Waste Electrical and Electronic Equipment) Directive has been put in place so that products at the end of life are recycled in the best way. When this product is out of order, please do not put it in your domestic waste bin. Please use one of the following disposal options: – Remove the batteries and deposit them in an appropriate WEEE skip. Deposit the product in an appropriate WEEE skip. – Or hand the old product to the retailer.
