4x4 DVI Matrix USER MANUAL www.gefen.
ASKING FOR ASSISTANCE Technical Support: Telephone (818) 772-9100 (800) 545-6900 Fax (818) 772-9120 Technical Support Hours: 8:00 AM to 5:00 PM Monday thru Friday. Write To: Gefen, Inc. c/o Customer Service 20600 Nordhoff Street Chatsworth, CA 91311 www.gefen.com support@gefen.com Notice Gefen Inc. reserves the right to make changes in the hardware, packaging and any accompanying documentation without prior written notice. The 4x4 DVI Matrix is a trademark of Gefen Inc. © 2007 Gefen Inc.
TABLE OF CONTENTS 1 Introduction / Operation Notes 2 Features 3 Panel Layout 4 Using the 4x4 DVI Matrix 5 RMT16-IR Installation 6 IR Codes 7 Dip Switch Guidelines 8 RS-232 Interface 9 4x4 DVI Matrix Rack Mount Diagram 10 Specifications 11 Terminology 12 Troubleshooting 13 Troubleshooting Diagram 14 Warranty
INTRODUCTION Thank you for purchasing the 4x4 DVI Matrix. The 4x4 DVI Matrix switches four DVI sources to any four DVI displays. The 4x4 DVI Matrix switcher has four DVI inputs and four DVI outputs. Matrix input #1 and the DVI port of DVI source #1 connects using a male to male DVI cable. The DVI port of DVI source #2 connects to DVI input #2. The DVI port of DVI source #3 connects to DVI input #3. The DVI port of DVI source #4 connects to DVI input #4.
FEATURES Features • Allows any DVI display to view any source at any time • Allows any source to be displayed on multiple displays at the same time • Maintains resolutions up to 1080p, 2K, and 1920x1200 • Maintains highest DVI single link video resolution • DVI or HDMI to DVI cables are used to connect the inputs and outputs of the matrix • Each display's inputs can be switched with the IR remote control or through RS232 Includes: (1) 4x4 DVI Matrix (4) DVI 6ft Male to Male Cables (1) 5VDC Power Supply (1)
DVI Inputs Back Panel DVI Outputs Display 1 LED Display 2 LED Display 3 LED Display 4 LED IR Extender Eye Port Indicator Indicator Indicator Indicator IR Sensor Front Panel 3 Connects to 5VDC Power Supply RS232 Controller Port Power Indicator PANEL LAYOUT
USING THE 4X4 DVI MATRIX 1 Connect all the sources to the DVI inputs on the 4x4 DVI Matrix, using the supplied cables. 2 Connect the HDMI/DVI displays to the outputs on the 4x4 DVI Matrix. 3 Connect the power supply to the 4x4 DVI Matrix 4 Controlling the 4x4 DVI Matrix using the RMT16-IR: Pressing Buttons... 1-4 5-8 9-12 13-16 Switches...
RMT16-IR Installation 1. Remove battery cover from the back of the RMT16-IR remote. 2. Verify that dip switches 1 & 2 are in the down (OFF) position. 3. Insert the battery, hold the battery so that you can see the positive side facing up. The side that is not marked must be facing down. 4. Test the RMT16-IR remote by pressing ONLY one button at a time. The indicator light on the remote will flash once each time you press a button.
IR CODES In the event of IR conflicts, please do the following: 1. Remove the battery cover from the back of the RMT16-IR remote. 2. Locate the Dip Switches above the batteries 3. Switch the Dip Switches on the RMT16-IR to any of the combinations pictured below. 4. Dip Switches 1 and 2 in the RMT16-IR correspond with Dip Switches 1 and 2 inside the 4x4 DVI Matrix respectively. Switch the switches inside the 4x4 DVI Matrix to match the same Remote Channel as the RMT16-IR.
DIP SWITCH GUIDELINES Underneath the 4x4 DVI Matrix are two banks of Dip Switches. Below is a table describing their functions. By default, the Bank of 8 switches are set of to the Off position and the other bank of 4 switches are set to ON. The bank of 4 dip switches are service switches and should not be changed from their ON position.
RS-232 INTERFACE Binary Table ASCII Corresponding RMT16-IR Button 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 Binary ASCII Corresponding RMT16-IR Button 9 9 a 10 b 11 c 12 d 13 e 14 f 15 g 16 0011 0001 0011 0010 0011 0011 0011 0100 0011 0101 0011 0110 0011 0111 0011 1000 Binary 0011 1001 0110 0001 0110 0010 0110 0011 0110 0100 0110 0101 0110 0110 0110 0111 RS232 Settings Bits per second ....................................................................................... 19200 Data bits ........................
4x4 DVI MATRIX RACK MOUNT DIAGRAM 9
SPECIFICATIONS Video Amplifier Bandwidth .................................................................1.65 Gbps Input Video Signal ......................................................................... 1.2 volts p-p Input DDC Signal .................................................................... 5 volts p-p (TTL) DVI Connector..................................................DVI-I 29 pin female (digital only) Single Link Range .............................................................
TROUBLESHOOTING If there is any video noise that appears on your output displays, you can resolve them by using the methods described in this section. AUTO EQUALIZATION Auto equalization is set to ON by default, but in some cases you may have to manually equalize the incoming source signal to eliminate video noise that occurs.
1 2 3 4 1 2 3 4 5 Equalization Trim Pot Display 1 Equalization Trim Pot Display 2 Equalization Trim Pot Display 3 Equalization Trim Pot Display 4 6 7 8 TROUBLESHOOTING - DIAGRAM Remove Tape Front Bottom 13 Pre-Emphasis Switches Auto Equalization Switches